Unconfigured Ad Widget

Collapse

Redding G-RX

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • oso grande
    Senior Member
    • Jun 2008
    • 869

    Redding G-RX

    Can this die be used for 10MM?

    OG
    Last edited by oso grande; 02-06-2014, 12:44 AM.
  • #2
    stilly
    I need a LIFE!!
    • Jul 2009
    • 10685

    Yes, but why?

    I just took a Lee carbide FCD in .40 cal and attached it to a single stage press after removing the top and crimper with a single roll of paper on the inside to cover the threads and it works like a champ. I "deglocked" about 600+ shells the other night.

    I used my .357 resizer ram to push the shells up. and a soda bottle or lee die bottle to catch the shells as they pop out the top.

    If you bought a Lee .40 cal carbide FCD (they are all carbide) AND a Lee .357 or .358 resizer, you are STILL only spending about $35 for a very similar tool and you will get a bottle that fits on top of the die already.
    7 Billion people on the planet. They aint ALL gonna astronauts. Some will get hit by trains...

    Need GOOD SS pins to clean your brass? Try the new and improved model...



    And remember- 99.9% of the lawyers ruin it for the other .1%...

    Comment

    • #3
      oso grande
      Senior Member
      • Jun 2008
      • 869

      Thanks stilly, I'm gonna give that a try.

      OG

      Comment

      • #4
        at_liberty
        Senior Member
        • Jun 2010
        • 699

        Originally posted by stilly
        Yes, but why?

        I just took a Lee carbide FCD in .40 cal and attached it to a single stage press after removing the top and crimper with a single roll of paper on the inside to cover the threads and it works like a champ. I "deglocked" about 600+ shells the other night.

        I used my .357 resizer ram to push the shells up. and a soda bottle or lee die bottle to catch the shells as they pop out the top.

        If you bought a Lee .40 cal carbide FCD (they are all carbide) AND a Lee .357 or .358 resizer, you are STILL only spending about $35 for a very similar tool and you will get a bottle that fits on top of the die already.
        Part of the reason "why" is because the G-Rx has the distinct advantage of pushing the case all the way through to the catch bottle. The Lee requires risking case mouth damage to push the previous case through to the bottle and out of the way of the following case.

        The G-Rx also has a cup for the case guide, so that there is less risk of getting fingers pinched and a greater opportunity for safely increasing input speed and then productivity.

        The advantage of the Lee is not only its price but that it can be used for 45 ACP also.

        Comment

        • #5
          thomashoward
          In Memoriam
          • Jan 2009
          • 1991

          Originally posted by oso grande
          Can this die be used for 10MM?

          OG
          yes
          http://i1150.photobucket.com/albums/...0fa5fefab1.jpghttp://i1150.photobucket.com/albums/...Untitled-2.jpghttp://i1150.photobucket.com/albums/...tar76148_1.jpg
          "Everyone has two lives,the second one starts when you realize you only have one "

          Comment

          • #6
            stilly
            I need a LIFE!!
            • Jul 2009
            • 10685

            Originally posted by at_liberty
            Part of the reason "why" is because the G-Rx has the distinct advantage of pushing the case all the way through to the catch bottle. The Lee requires risking case mouth damage to push the previous case through to the bottle and out of the way of the following case.

            The G-Rx also has a cup for the case guide, so that there is less risk of getting fingers pinched and a greater opportunity for safely increasing input speed and then productivity.

            The advantage of the Lee is not only its price but that it can be used for 45 ACP also.
            Sounds like you have not done it with a Lee FCD...

            I will test a couple of 10mm but if I put them in with the shell over the ram (.40 anyways) there is nary an issue. but if I put them in so that the case mouth goes FIRST, it is weird, but still clears that carbide pass through ring.
            7 Billion people on the planet. They aint ALL gonna astronauts. Some will get hit by trains...

            Need GOOD SS pins to clean your brass? Try the new and improved model...



            And remember- 99.9% of the lawyers ruin it for the other .1%...

            Comment

            • #7
              J-cat
              Calguns Addict
              • May 2005
              • 6626

              The GRX is a refined push-through die. It is well made. The Lee is a half-arsch measure.

              Comment

              • #8
                at_liberty
                Senior Member
                • Jun 2010
                • 699

                Originally posted by J-cat
                The GRX is a refined push-through die. It is well made. The Lee is a half-arsch measure.
                The Lee works for a lot less money. If you want only functionality and value, get the Lee.

                Comment

                • #9
                  at_liberty
                  Senior Member
                  • Jun 2010
                  • 699

                  Originally posted by stilly
                  Sounds like you have not done it with a Lee FCD...
                  I have both Lee and Redding but might be confusing head first with mouth first. Mouth first is definitely best and I believe as intended. It's been about three years because I did a bucket full of 40 at one time.
                  Last edited by at_liberty; 02-07-2014, 11:40 AM.

                  Comment

                  • #10
                    fizux
                    Senior Member
                    CGN Contributor - Lifetime
                    • Apr 2012
                    • 1540

                    The issue with glocked .40 is that the brass gets pushed down a little at a time, but even a FL resize die can't reach the very bottom. The bottom gets fatter, and can't be handled on a progressive.

                    There are four generally accepted solutions, in order of initial cost:
                    1. Pitch the bulged brass;
                    2. Lee FCD w/ Bulge Buster Kit;
                    3. Redding GRX; and
                    4. Case Pro.

                    The Lee FCD and Redding GRX solutions involve pushing the case through the die -- some folks prefer to do it backwards (base first), which extrudes the excess fat back towards the mouth of the case.

                    If you are going to do a lot, get the Case Pro. I don't own one, but everyone I know who does tells me its awesome and to get one. The cost is so obscene that my entire post would be censored if i repeated it here, but lets just say that a Dillon 650 is cheaper. I usually use method #1 -- pitched into bucket #3,217 for whenever I do get a Case Pro (or need brass desperately enough to go back to the FCD/GRX solution).
                    Last edited by fizux; 02-09-2014, 12:56 AM.
                    Nationwide Master List of Current 2A Cases, courtesy of Al Norris @ TFL.

                    Reloading Clubs: SF, East Bay

                    Case Status: (Handgun Roster). SF v. 44Mag (Mag Parts Kits). Bauer v. Harris (DROS Fees). Davis v. LA (CCW policy). Jackson v. SF (Ammo/Storage). Teixeira (FFL Zoning). First Unitarian v. NSA (Privacy). Silvester (Waiting Period). Schoepf (DROS Delay). Haynie (AW ban). SFVPOA v. SF (10+ mag possession ban). Bear in Public: Drake (3CA); Moore (7CA); Richards, Peruta, McKay (9CA).

                    Comment

                    • #11
                      stilly
                      I need a LIFE!!
                      • Jul 2009
                      • 10685

                      Yeah, When I do base first it goes in smooth, but mouth first it pops instead of being nice. Makes the whole bench thump too...
                      7 Billion people on the planet. They aint ALL gonna astronauts. Some will get hit by trains...

                      Need GOOD SS pins to clean your brass? Try the new and improved model...



                      And remember- 99.9% of the lawyers ruin it for the other .1%...

                      Comment

                      Working...
                      UA-8071174-1