Unconfigured Ad Widget
Collapse
|
|
|
|
|
|
|
|
Noob getting into reloading..
Collapse
X
-
-
I'm also looking at getting into reloading soon and have a similar shopping list. Powder seems to be the rate limiting factor, so I'm in no hurry.
Just a heads up on harbor freight, I have one next to my work. Everything I have ever bought there over the past few years broke after a few uses. I'm not saying it's all bad, just beware.sigpicComment
-
if this is an offer to sell to anyone then ill take it!I don't know where Rancho Cordova is but if you can you drive to San Diego I'll sell you a fully loaded LCT with every upgrade they make for $100. I think I have around $185 into it. I've loaded maybe 100 rounds on it. Probably closer to 50. I bought I simply to see if all the internet rumors where true. They are. It's a great press. I'll even through in some 9mm/45/223 brass for you
Comment
-
Buy a Dillon 550 and complete tool heads {Dillon dies are great} for each caliber. A Balance beam scale and a tumbler of some kind to clean the brass.
I have had my 550 since 1991 and the cost per year is chump change, buy once and cry once.California's politicians and unionized government employees are a crime gang that makes the Mexican drug cartels look like a Girl Scout Troop in comparison.Comment
-
Single stage does tend to get old for pistol reloading but it depends on if you enjoy the reloading. I really like it and I like the quality control. They're so inexpensive I recommend starting with one. If you decide you want to get something else later you still have a backup or you can resell it and barely take a hit.
Thank being said, I would be caseful with what you skimp on to begin with because if you end up enjoying reloading you'll end up upgrading nearly everything.
RCBS uniflow powder measure over the Lee Perfect Powder Measure. I guess the lee powder measures with the discs on the turrets/progressives must measure better than the $20 model you get on its own because I would never trust my lee perfect powder measure without weighing every 3rd or 4th load. I'll get 5.4 grains consistently for 5 charges then suddenly get 6.1 or 4.8. Sometimes it can be fixed with a quick adjustment, other times I'm spending 5 minutes or more going back and forth trying to get back to my desired charge.Comment
-
A year ago I was in the position you are now. Except I just went with the Lee starter kit, and you are right, I did waste my money on the crappy starter pieces. I have now replaced most of the items that came with a starter kit. The only things that have run fine so far are the press and the Lee Dies.
First one to go was the balance scale. I replaced it with a Frankford Arsenal Digital scale.
Next was the Lee trimmer. The one that pops in the Drill. Replaced it with a Forster Original Case Trimmer.
I just recently replaced the powder measure. The Lee one broke the handle about 3 months after using it, which I then fixed. It started leaking a few months after that . Just replaced it with a Hornady Powder Measure. So much better. Just dont like that you cant lock the hopper off. Oh well.
Good luck and happy reloading.Comment
-
It is kinda like going to jail, "Just drop the soap ONCE in the shower for us and we will respect you after that..."
OP:
To answer your questions:
1. I dunno WTF a 3/4 stage turret is. A turret is a turret. OH, I get it. Referring to the Lee classic turret in 4 hole vs lee precision turret at 3 hole. Yeah go with the Classic 4 hole cast turret, it looks like an arrow, NOT the aluminum one. ELSE you can consider getting a more expensive turret with 6-7 holes from Redding or Lyman. They are good too, but not as fast and certainly not as cheap as a Lee Classic Turret (4 hole).
2. Scale for measuring powder I use the American Weigh Milligram scale and at $23.00 on amazon it is hard to beat for its precision and list of excellent features. I have an RCBS 5-0-5 as a backup and it works nicely, but I found mine for $65 minus the powder pan.
3. Powder dispensing is best with a Hornady Lock N Load dropper if you compare it against the RCBS Uniflow or the Lee Auto Disk Pro dropper. Although the Lee aint so bad if you do not mind a flake or two of powder on your hands.
4. Case trimmers, talk to Bronco. He found an excellent set of trimmers that are very easily changed out for calibers. Cheaply affordable as well.
In all honesty, if you want to start smart and not break the bank then there are TWO things you can do.
1. Get the RCBS Master Jedi kit for around $300-$400 and then just get a digital scale (American Weigh) if you want to. The RCBS kit has 99.9% of the things that you will need with minimal flab. They include a lube pad in it, but there is no need for that if you get the Hornady Unique or Imperial Sizing Wax. The only thing you should have to get is a set of calipers (HF special for $15.00) and the dies for your calibers I think. This will get you an excellent somewhat heavy duty press to learn on although making ammo will be slower in comparison to choice 2.
OR
2. Piece together a kit of your own like I and others like to do. But get the Lee Classic Turret and since you get to pick and choose here, get a Hornady lock & Load powder dropper with case activated linkage, American Weigh digital milligram scale, Calipers, Lee Carbide 3-die sets for your pistol calibers, RCBS Dies for your Rifle sets, then evaluate and see if you want to prime on the press or hand prime and as far as cleaning your brass goes you can decide dry or wet process. Dry process has an initial low startup in cost, but you pay for it by how messy it can be along with dust and not having clean primer pockets. Wet process costs more, but is quieter and does not leave dust anywhere. This approach will get you in the door for an initial startup of around $200-$300 with one-two die sets. You can pick up other things as you need to later on. This will start you with an excellent press that is the FASTEST you can buy without going progressive (expensive yet fastest period). You can also look for a used single stage press and go this route too and chop off about $75 from this price also. OR you can buy a different turret press such as a T-mag or T-7 but you will be back around the $400+ mark then.
Personally speaking, the Diva in me likes to shop and shop I did. When you piece together a set using the Lee Classic Turret, you get maximum speed and savings.
Just know this, no matter WHAT you decide to get, most if not ALL reloaders have a single stage, but NOT all reloaders have a progressive. In fact, not even MOST reloaders have a progressive press unless they have to crank out a ton of ammo.
AND now that I have typed this out I see that you have already put together a list and possibly made a purchase. Damn I am slow. Not to shabby though.
If you are reloading for an AR or ANY type of semi auto .223/.308 then that hornady trimmer will last you about 50 rounds before you toss it and buy a faster one. There aint no way in HELL I would ever sit long enough to load up 3000+ cases to be trimmed at 10+ seconds each... Oh and then deburred and chamferred too? HELL NO. we talking 13 hours vs 3 hours of work...
OH, one thing that I would do would be to drop the Hornady book from the list and get the Modern Reloading book by Lee. IT has more caliber recipes then all others.
And you will love that turret. If you need any help setting it up you know where to go...
I think you should leave the sonics for gun parts. For cleanign shells, dry or wet process, you wanna save money on startup, go for dry processing, you want better longer lasting stuff, go with wet processing...Last edited by stilly; 07-27-2014, 8:50 AM.7 Billion people on the planet. They aint ALL gonna astronauts. Some will get hit by trains...
Need GOOD SS pins to clean your brass? Try the new and improved model...

And remember- 99.9% of the lawyers ruin it for the other .1%...Comment
-
Yes I have heard that RCBS Uniflow dispenser does a lot better than the Lee Perfect Powder Measure. It makes me reconsider buying any kit and instead buying each part individually, or I might just go back and forth between the RCBS Supreme Master Reloading kit and the damn Lee Classic Turret kit. Either way I am looking at having to replace the lee balance, and lee powder dispenser most likely for more accurate and more reliable parts, which kind of defeats the purpose of buying the kit. Might as well just buy the dang press, scale, dispenser all separately.Single stage does tend to get old for pistol reloading but it depends on if you enjoy the reloading. I really like it and I like the quality control. They're so inexpensive I recommend starting with one. If you decide you want to get something else later you still have a backup or you can resell it and barely take a hit.
Thank being said, I would be caseful with what you skimp on to begin with because if you end up enjoying reloading you'll end up upgrading nearly everything.
RCBS uniflow powder measure over the Lee Perfect Powder Measure. I guess the lee powder measures with the discs on the turrets/progressives must measure better than the $20 model you get on its own because I would never trust my lee perfect powder measure without weighing every 3rd or 4th load. I'll get 5.4 grains consistently for 5 charges then suddenly get 6.1 or 4.8. Sometimes it can be fixed with a quick adjustment, other times I'm spending 5 minutes or more going back and forth trying to get back to my desired charge.Comment
-
I am thinking of going with a piece together kit from individual parts.It is kinda like going to jail, "Just drop the soap ONCE in the shower for us and we will respect you after that..."
OP:
To answer your questions:
1. I dunno WTF a 3/4 stage turret is. A turret is a turret. OH, I get it. Referring to the Lee classic turret in 4 hole vs lee precision turret at 3 hole. Yeah go with the Classic 4 hole cast turret, it looks like an arrow, NOT the aluminum one. ELSE you can consider getting a more expensive turret with 6-7 holes from Redding or Lyman. They are good too, but not as fast and certainly not as cheap as a Lee Classic Turret (4 hole).
2. Scale for measuring powder I use the American Weigh Milligram scale and at $23.00 on amazon it is hard to beat for its precision and list of excellent features. I have an RCBS 5-0-5 as a backup and it works nicely, but I found mine for $65 minus the powder pan.
3. Powder dispensing is best with a Hornady Lock N Load dropper if you compare it against the RCBS Uniflow or the Lee Auto Disk Pro dropper. Although the Lee aint so bad if you do not mind a flake or two of powder on your hands.
4. Case trimmers, talk to Bronco. He found an excellent set of trimmers that are very easily changed out for calibers. Cheaply affordable as well.
In all honesty, if you want to start smart and not break the bank then there are TWO things you can do.
1. Get the RCBS Master Jedi kit for around $300-$400 and then just get a digital scale (American Weigh) if you want to. The RCBS kit has 99.9% of the things that you will need with minimal flab. They include a lube pad in it, but there is no need for that if you get the Hornady Unique or Imperial Sizing Wax. The only thing you should have to get is a set of calipers (HF special for $15.00) and the dies for your calibers I think. This will get you an excellent somewhat heavy duty press to learn on although making ammo will be slower in comparison to choice 2.
OR
2. Piece together a kit of your own like I and others like to do. But get the Lee Classic Turret and since you get to pick and choose here, get a Hornady lock & Load powder dropper with case activated linkage, American Weigh digital milligram scale, Calipers, Lee Carbide 3-die sets for your pistol calibers, RCBS Dies for your Rifle sets, then evaluate and see if you want to prime on the press or hand prime and as far as cleaning your brass goes you can decide dry or wet process. Dry process has an initial low startup in cost, but you pay for it by how messy it can be along with dust and not having clean primer pockets. Wet process costs more, but is quieter and does not leave dust anywhere. This approach will get you in the door for an initial startup of around $200-$300 with one-two die sets. You can pick up other things as you need to later on. This will start you with an excellent press that is the FASTEST you can buy without going progressive (expensive yet fastest period). You can also look for a used single stage press and go this route too and chop off about $75 from this price also. OR you can buy a different turret press such as a T-mag or T-7 but you will be back around the $400+ mark then.
Personally speaking, the Diva in me likes to shop and shop I did. When you piece together a set using the Lee Classic Turret, you get maximum speed and savings.
Just know this, no matter WHAT you decide to get, most if not ALL reloaders have a single stage, but NOT all reloaders have a progressive. In fact, not even MOST reloaders have a progressive press unless they have to crank out a ton of ammo.
AND now that I have typed this out I see that you have already put together a list and possibly made a purchase. Damn I am slow. Not to shabby though.
If you are reloading for an AR or ANY type of semi auto .223/.308 then that hornady trimmer will last you about 50 rounds before you toss it and buy a faster one. There aint no way in HELL I would ever sit long enough to load up 3000+ cases to be trimmed at 10+ seconds each... Oh and then deburred and chamferred too? HELL NO. we talking 13 hours vs 3 hours of work...
OH, one thing that I would do would be to drop the Hornady book from the list and get the Modern Reloading book by Lee. IT has more caliber recipes then all others.
And you will love that turret. If you need any help setting it up you know where to go...
I think you should leave the sonics for gun parts. For cleanign shells, dry or wet process, you wanna save money on startup, go for dry processing, you want better longer lasting stuff, go with wet processing...
Parts List (Updated):
Lee Classic Turret press - Amazon for $112
RCBS 10-10 Balance Scale - Amazon for $144
Lee Precision Safety Primer Feed Large and Small - Amazon for $23
Hornady Lock N Load Powder Measure - Amazon for $66
Hornady case activating linkages - Amazon for $58
Frankford Arsenal Quick-n-Ez Case Tumbler - Amazon for $39
Frankford Arsenal Quick-n-Ez Impact Bullet Puller - Amazon $15
Lee Precision Universal Press Shell Holder Set - Amazon for $27
In addition added Lee Shotshell reloading for 12gauge:
Lee Precision II Shotshell Reloading Press 12 Gauge - Amazon for $51
MTM 50 round shotshell tray - Amazon for $5
Books:
Lyman Shotshell Handbook 5Th Edition - Amazon for $18
Lyman 49Th Edition Reloading Handbook - Amazon for $18
The Beginner's Guide to Reloading Ammunition - Amazon for $10
Lee Precision Modern Reloading 2nd Edition - Amazon for $20
Grand Total: $653.72 (w/ CA tax %7.875 local + state, and with free amazon prime shipping)
I also did see harbor freight have nice dial calipers for around $20ish. I really do worry about the precision with a slide caliper.Comment
-
Still too much money!!!I am thinking of going with a piece together kit from individual parts.
Parts List (Updated):
Lee Classic Turret press - Amazon for $112
RCBS 10-10 Balance Scale - Amazon for $144
Lee Precision Safety Primer Feed Large and Small - Amazon for $23
Hornady Lock N Load Powder Measure - Amazon for $66
Hornady case activating linkages - Amazon for $58
Frankford Arsenal Quick-n-Ez Case Tumbler - Amazon for $39
Frankford Arsenal Quick-n-Ez Impact Bullet Puller - Amazon $15
Lee Precision Universal Press Shell Holder Set - Amazon for $27
In addition added Lee Shotshell reloading for 12gauge:
Lee Precision II Shotshell Reloading Press 12 Gauge - Amazon for $51
MTM 50 round shotshell tray - Amazon for $5
Books:
Lyman Shotshell Handbook 5Th Edition - Amazon for $18
Lyman 49Th Edition Reloading Handbook - Amazon for $18
The Beginner's Guide to Reloading Ammunition - Amazon for $10
Lee Precision Modern Reloading 2nd Edition - Amazon for $20
Grand Total: $653.72 (w/ CA tax %7.875 local + state, and with free amazon prime shipping)Keep it simple!Comment
-
Reloading is a HOBBY of it's own. Spending time reloading is relaxing (unless it's 2am the morning of a match and you still have to drive 4 hours to the range). Progressive presses are great for straight walled cartridges and can work OK for bottle necked cartridges as long as the reloader does brass prep prior to loading. Personally, I believe every reloading bench should have at least one single stage press on it. So, IMHO, starting with a SS is the way to go.
For a balance, a beam balance is always going to be both precise and accurate. Electronic balances can have issues with all sorts of outside influences which will cause readings to float or just be wrong. You need to let them warm up for hours/days prior to use. A cell phone, fluctuations in household current, florescent lighting, stereo speakers, etc. can all cause very dangerous errors in the way an electronic balance reads.
For dispensing powder, a basic powder dispenser from Redding, RCBS, Hornady, etc will all work fine. Some people even swear by Lee. I don't have experience with Lee powder measures so, I can't give an educated opinion on them.
As far as trimmers go, There are three basic types. Ones that use the case head to index on. Ones that use the inside of the case head as an index point and ones that index off the shoulder. All three have pros and cons. While I have and use all three types, I prefer those that use a datum point on the shoulder like the Giruard, Trim-It, Possum Hollow, WFT, etc. But, you need a dedicated bushing or trimmer for each different cartridge. Lathe type trimmers are the most versatile. One's choice in trimmers should be based on individual needs and wants. I will never get rid of my Lyman lathe trimmer because, it's the best choice for me when trimming small runs (50-200) rounds of odd cartridges like 7.35 Carcano. Also, while you need dedicated pilots for each caliber, the same caliber pilot works with many different cartridges. A basic .308 caliber pilot works for 30-30, .308, 30-06, 7.5 swiss, and just about any .30 caliber cartridge.NRA Certified Pistol, Rifle, Shotgun and Metallic Cartridge Reloading Instructor
California DOJ Certified Fingerprint Roller
Ventura County approved CCW Instructor
Utah CCW Instructor
Offering low cost multi state CCW, private basic shooting and reloading classes for calgunners.
sigpic CCW SAFE MEMBERSHIPS HERE
KM6WLVComment
-
Hey thanks. Yea I have been trying to find a good set of case trimmers that won't take forever to trim and deburr each case but won't cost an arm and a leg.Reloading is a HOBBY of it's own. Spending time reloading is relaxing (unless it's 2am the morning of a match and you still have to drive 4 hours to the range). Progressive presses are great for straight walled cartridges and can work OK for bottle necked cartridges as long as the reloader does brass prep prior to loading. Personally, I believe every reloading bench should have at least one single stage press on it. So, IMHO, starting with a SS is the way to go.
For a balance, a beam balance is always going to be both precise and accurate. Electronic balances can have issues with all sorts of outside influences which will cause readings to float or just be wrong. You need to let them warm up for hours/days prior to use. A cell phone, fluctuations in household current, florescent lighting, stereo speakers, etc. can all cause very dangerous errors in the way an electronic balance reads.
For dispensing powder, a basic powder dispenser from Redding, RCBS, Hornady, etc will all work fine. Some people even swear by Lee. I don't have experience with Lee powder measures so, I can't give an educated opinion on them.
As far as trimmers go, There are three basic types. Ones that use the case head to index on. Ones that use the inside of the case head as an index point and ones that index off the shoulder. All three have pros and cons. While I have and use all three types, I prefer those that use a datum point on the shoulder like the Giruard, Trim-It, Possum Hollow, WFT, etc. But, you need a dedicated bushing or trimmer for each different cartridge. Lathe type trimmers are the most versatile. One's choice in trimmers should be based on individual needs and wants. I will never get rid of my Lyman lathe trimmer because, it's the best choice for me when trimming small runs (50-200) rounds of odd cartridges like 7.35 Carcano. Also, while you need dedicated pilots for each caliber, the same caliber pilot works with many different cartridges. A basic .308 caliber pilot works for 30-30, .308, 30-06, 7.5 swiss, and just about any .30 caliber cartridge.Comment
-
If you don't want to chamfer and debur each case, you'll want a 3 way trimmer. Trim-It is a new company and is introducing a 3 way trimmer soon. I will be getting one of the first ones soon and evaluating it on a 50BMG case. I will compare it to my CH4D, K&M, and Giraud trimmers that I've used for 50BMG. However, one issue with 3 way cutting heads is the need to adjust them for each caliber where a flat cutting head doesn't require that adjustment. Three way cutters also tend to cost more than flat cutters.NRA Certified Pistol, Rifle, Shotgun and Metallic Cartridge Reloading Instructor
California DOJ Certified Fingerprint Roller
Ventura County approved CCW Instructor
Utah CCW Instructor
Offering low cost multi state CCW, private basic shooting and reloading classes for calgunners.
sigpic CCW SAFE MEMBERSHIPS HERE
KM6WLVComment
Calguns.net Statistics
Collapse
Topics: 1,870,743
Posts: 25,175,400
Members: 358,862
Active Members: 5,389
Welcome to our newest member, 1776 Arms.
What's Going On
Collapse
There are currently 29252 users online. 161 members and 29091 guests.
Most users ever online was 239,041 at 11:39 PM on 02-14-2026.


Comment