I started on a little RCBS Pardner, bit the bullet (sorry...) and got a dillon RL550B to make all of my volume ammo, and just bought a Lee Classic Cast Turret to replace the RCBS (going to become my mobile press)... It'll make at least as accurate ammo as the worn out old RCBS, but has the convenience of keeping all the tooling in the turret set up for next time like the Dillon.
Unconfigured Ad Widget
Collapse
|
|
|
|
|
|
|
|
Done with Progressive reloading
Collapse
X
-
For all you ever needed to know to run your Lee Pro 1000 correctly.
Comment
-
I'd like to watch some of the fumblers set up and operate their progressive press. I've seen a few, and there was something obvious, to me at least, that they were doing something wrong.
Lightweight table that bounced around, check.
Running crimped primer brass without removing the crimp, check.
Letting the primer feed go empty, check.
Adjusting the dies so one was lower than the rest, (not supposed to be), check.
Not cleaning the shell plate and priming attachment when needed. check.
Yanking on the lever to force the ram over whatever was in the way. check.
Not doing full up and down strokes on the ram. check.
Not doing a smooth, pause at either end, stroke of the ram. check.
Not pretreating the powder measure to remove static electricity. check
I got more, but you get the idea. I ran my Loadmaster with the original primer slider for around 7,000 rounds. That's the part the fumblers buy by the gross. There really are a LOT of people that shouldn't go near reloading, they just don't have a clue what is important. And probably never will.Comment
-
I did looked at Lee's Pro 1000 at one time. Watch a few videos, but it just seems to require a lot shacking to the primer feeder and powder to drop to work correctly. I'm sure once you get into the flow of things, it works well. But, I decided to go with Hornady instead.
With that said, I do own a Lee Classic Single stage press and a couple of their dies and accessories. They all work well, but the quality of construction is definitely a grade below all others on the market. But, again, Lee is also the lease inexpensive of all. So, I still think they are good value. Just don't expect a turn-key solution when buying Lee.
.Comment
-
-
+1For all you ever needed to know to run your Lee Pro 1000 correctly.
http://www.sanfranciscoliberalwithagun.com/pro1000.html
This link should be included with every 1000 sold.
That was my first press. I bought it and started loading .223 with it. That was the WRONG load to start my reloading career with! Especially on 1000! I came across the link above and was able to get my machine running as smooth as well oiled sewing machine.
After thousands of rounds reloaded with the 1000.......I saw the light and bought a dillon 650. Now that's a whole different kind of smooth machine!
I still have have the 1000. It now serves as a backup. I'd have no problem putting it back into service if needed.Originally posted by meIt's all about standards. You have yours and I have mine. Mine just happen to be higher.Comment
-
I bought a pro 1000, figured I could skip the single stage....well I ended up buying a single stage anyhow, and wantd to throw the pro 1000 out the window every time I used it.
Then one day it just clicked, and I got everything running great. I can really knock out the ammo with it.
That said, right now that auto case feeder is busted, the primer lever got un attached during a shell plate change, but it does actually work.
It's served its purpose. i've done thousands of rounds of 223 and 9mm on it, when I finally get tired of it I'll joyously chuck it in the trash and switch to something better. In all honesty though, it does actually work just fine, often for *tens* of minutes at a time! ;-)
I should probably just keep it and leave it set up for .223, since I hand prime those anyhow.
None of the problems with it are insurmountable, just mildly annoying and pile up if you let them.
haha yes a wobbly table will drive you nuts, especially iwth the shell feeder full! Another thing that works great, but isn't particularly robust.
Honestly the problems I had with it were my own fault and inexperience. I'd force things, let primers run out, not check cases to make sure they had powder, not properly set the powder chain, etc etc etcComment
-
Buy a real press and come back to the dark side. Buying a Lee pro 1,000 is like marrying a liberal, you can try to make it work but it will only lead frustration then separation.se carga el diablo de la pistola...
.223, .25acp, 25-20win, 9mm, 38spl/.357, 10mm .308, 8mm M, 7mm Rem Mag, 45acp, .475 Wildey mag
On 2 Hornady LnL AP & Dillon Super 1050Comment
-
That's funny
I enjoy the Lee turret but really LOVE my 550...
For rifle rounds, RC rocks.
WTB S&W 29/629 - 44mag 4" / Colt Commander 70 series
"If we make enough laws, we can all be criminals." -Jeff Snyder
"I will be spending the weekend studying...oh, and paying my taxes so they can continue to keep us safe from zombies, ghosts and goblins."
Ollshooter32
[/I]Comment
-
Originally posted by meIt's all about standards. You have yours and I have mine. Mine just happen to be higher.Comment
-
I use both.
I'm not going to do a caliber conversion on a Dillon 650 to load 20 rounds of 7.65 Agentine.
Comment
-
Statement of facts is "fighting words"? By definition, half of the population is below average in mechanical ability/reasoning. I've seen the results of that half when they try to do something difficult; like change a flat tire.
Or a light bulb, or use a ladder. It's pathetic, and yet they are allowed to purchase reloading equipment. There ought'a be a law or something!!
Comment
Calguns.net Statistics
Collapse
Topics: 1,870,902
Posts: 25,177,339
Members: 358,862
Active Members: 5,395
Welcome to our newest member, 1776 Arms.
What's Going On
Collapse
There are currently 31379 users online. 138 members and 31241 guests.
Most users ever online was 239,041 at 11:39 PM on 02-14-2026.

Comment