MasterPieceArms

[hefedehefe]

I'll do that. I started looking around and they are kinda hard to find. Especially in 10 round. One military surplus guy even told me that a 10 round is high capacity. WTF. Seems to be an idiot or maybe something I don't know.lol

[JagerTroop]

If you're just looking for a 10rd, tapco mags aren't too bad. Its when you load them to 32, they start to bulge at the lips.

[hefedehefe]

I had that problem but with my top cocker and I got some frag in my finger, not really sure how that happened and it was only once. Check out USMachinegun.com for accessories if you haven't already. I got the mag release extension and the front strap (kinda nice but mainly for traditional looks). Also put a rear sling swivel on it and have an underarm sling harness for it. Have fun bump firing that bad boy!

Where did you get that rear swivel?

[voiceoftheright]

Where did you get that rear swivel?

They sell some on USMG but I made this one fairly easy and for a fraction of the cost. Just get a swivel nut/adapter (whatever the dome shaped adapter with a hole in it for a Mike's sling swivel is called). I put a nut on the inside of the receiver, stuck the adapter threads up through the hole already in the receiver and tightened it down, then just put on the sling swivel. It kinda rubs the back of your shooting hand but I don't notice it and am able to get the same grip without it on. The hardest part is getting the inside nut lined up with the hole so you can begin tightening it down. I just used a flathead to hold it in place before tightening it from outside.

[hefedehefe]

I'm going to try it this weekend. We should start a mac club lol

[hefedehefe]

They sell some on USMG but I made this one fairly easy and for a fraction of the cost. Just get a swivel nut/adapter (whatever the dome shaped adapter with a hole in it for a Mike's sling swivel is called). I put a nut on the inside of the receiver, stuck the adapter threads up through the hole already in the receiver and tightened it down, then just put on the sling swivel. It kinda rubs the back of your shooting hand but I don't notice it and am able to get the same grip without it on. The hardest part is getting the inside nut lined up with the hole so you can begin tightening it down. I just used a flathead to hold it in place before tightening it from outside.

Can you take a closer picture though. I'm looking at the mike's part and dont see how it is going to fit. What model did u use?

[voiceoftheright]

Can you take a closer picture though. I'm looking at the mike's part and dont see how it is going to fit. What model did u use?

I pieced it together, not sure. Check out this link. Just use a threaded sling stud and a swivel like shown. You'll need to find a nut that will work with the sling stud to put on the inside of your receiver.

http://www.cabelas.com/link-12/product/0005838220727a.shtml

[CALI-gula]

I just bought an MPA930 and love it.

Too funny: you created a thread about the Draco and this Masterpiece (side-cocker version)- I am picking up BOTH today that I DROS'ed a few weeks ago!!!

.

[hefedehefe]

Nice. I did the same(got them together) They go good together

[hefedehefe]

They are like peas and carrots

[Atlantic Firearms]

So how are these made CA Compliant ?

[Heavy_Grinder]

So how are these made CA Compliant ?

Out of state, a Titan muzzle brake is pinned/welded to the threaded barrel to get it up to minimum length for DROS in California which is 6 inches. A wooden block is then stuffed in the magwell which is held in place via rear grip screw.

Pistol is then DROS'd as single shot. After the ten days are up, buyer then can remove block and utilize pre-ban Sten Mags or Grease gun mags depending on which caliber they bought. No lock necessary whatsoever.

^^This is the sole and only reason why I purchased a MPA30 in the first place, to finally put my old Sten mags to use^^

[Atlantic Firearms]

So there is no Bullet button device required for these pistols ? The AK pistols require a Bullet button .

[SJgunguy24]

So there is no Bullet button device required for these pistols ? The AK pistols require a Bullet button .

In bold below. MPA's have been in CA for a while, PRKarms has been offering the entire line of MPA pistols and carbines since the beginning of the year.

12276.1. (a) Notwithstanding Section 12276, "assault weapon" shall also mean any of the following:

(4) A semiautomatic pistol that has the capacity to accept a detachable magazine and any one of the following:
(A) A threaded barrel, capable of accepting a flash suppressor, forward handgrip, or silencer.
(B) A second handgrip.
(C) A shroud that is attached to, or partially or completely encircles, the barrel that allows the bearer to fire the weapon without burning his or her hand, except a slide that encloses the barrel.
(D) The capacity to accept a detachable magazine at some location outside of the pistol grip.
(5) A semiautomatic pistol with a fixed magazine that has the capacity to accept more than 10 rounds.

[hefedehefe]

I need a sten mag. I only have the tapco. Where is a good place to get one?