Unconfigured Ad Widget

Collapse

Xtreme 230gr RN problem

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • #16
    J-cat
    Calguns Addict
    • May 2005
    • 6626

    Originally posted by 1bulletBarney
    I started a thread about a week ago over a question about a OAL for a x-treme 200 grn plated RN. One of the posters replied that it wasnt neccesary to flare case mouth because said bullet was rounded/tapered at base and would fit in a unflared case.

    That poster is usually spot on but that time he was mistaken and if I would have tried to set those bullets as suggested I am sure I would have had the same results as the OP...
    I don't flare the case mouth for these bullets. I never had this problem.

    I wonder if the OP trimmed his cases and left the case mouth sharp?

    Or perhaps his seater die bore is too tight. If so, then no amount of flare will help because the bore constriction will close the case mouth right up.

    Comment

    • #17
      J-cat
      Calguns Addict
      • May 2005
      • 6626

      Originally posted by xtremetib
      I too had that same problem even with flared case mouth
      had too back my bullet seat/crimp die out more than normal and I crimp in the next station
      That's a good solution.

      Comment

      • #18
        'ol shooter
        Veteran Member
        • Mar 2011
        • 4646

        I have loaded and shot a few thousand of them without issue, they are plenty accurate if loaded properly. I bell the case mouths slightly, and swab the case mouths with dry neck sizing lube, crimp enough that they drop freely into my gauge, good to go. I have had issues in the past with Berry's wrinkling the plating if I didn't dry lube the case mouths.
        sigpic
        Bob B.
        (\__/)
        (='.'=)
        (")_(")

        Comment

        • #19
          J-cat
          Calguns Addict
          • May 2005
          • 6626

          Lubing the case mouth encourages bullet setback. Friction is desirable in metallic cartrige reloading.

          Comment

          • #20
            p1choco
            Senior Member
            • Sep 2007
            • 583

            Best solution is to trim your all your brass to the same same size. Preferably the shortest case length you have as long as it meets minimum case length. Chamfer all your cases. Setting the a uniform case length will ensure all cases get the same flare. If you were loading jackets bullets you probably wouldn't need much flare. But loading plated or cast bullets are wider diameter so those will need more flare. Just enough not too peel back the plating/lead.Seat and crimp and call it a day. Whoever says you don't need flare obvoiusly isn't seasoned enough to be giving reloading advise.

            Comment

            • #21
              J-cat
              Calguns Addict
              • May 2005
              • 6626

              Really?

              How many years of loading Xtreme bullets does it take to become seasoned enough?

              Comment

              • #22
                Bigtls1
                Senior Member
                • Sep 2012
                • 579

                2. Definitely 2.

                Comment

                • #23
                  Bigtls1
                  Senior Member
                  • Sep 2012
                  • 579

                  Just kidding J-cat

                  Comment

                  • #24
                    jumbopanda
                    Calguns Addict
                    • Aug 2006
                    • 8382

                    Let me recommend the Lyman M die.



                    Instead of flaring the case mouth, it creates a small step that is just over the bullet diameter, making it easy to set the bullet in straight, and pretty much eliminates any chance of bullet shaving.

                    You can also order additional plugs for different calibers from Lyman.
                    Mo' BBs.

                    Comment

                    • #25
                      p1choco
                      Senior Member
                      • Sep 2007
                      • 583

                      I didn't mean loading Xtteme bullets specifically. Although Xtreme does make plated and lead cast who's diameters vary. The art of hand loading isn't always cut and dry and. And because something works for you doesn't mean it's going to work for everyone. Handload long enough and you'll eventually encounter an anomaly where what has always worked for you, won't work.

                      Comment

                      • #26
                        J-cat
                        Calguns Addict
                        • May 2005
                        • 6626

                        This thread is about Xtreme bullets specifically. They have round bases that do not require a flare. A straight case mouth will allow the base of these bullets to slip through without shaving unless 1. It is sharp or 2. The die is constricting the case mouth as the bullet is seated. If that is the case then no amount of flare will help because the die will immediately close the flare. Backing out the die will sometimes help if the bore is tapered, but then you'll lave to crimp in a separate step.

                        Comment

                        • #27
                          p1choco
                          Senior Member
                          • Sep 2007
                          • 583

                          Size, bell, seat, crimp. It's obvious those cases needed flaring no matter what type of base. Especially with "Extreme" platted bullets because the plating isn't as robust as a jacketed bullet. BTW, a seating die seat will only seat and shouldn't allow the case to roll into the bullet. If seating and crimping in the same step, then the crimp shouldn't happen until the bullet is seated. Take a good look at those pictures. Those bullets were peeled back quite a ways.

                          Hk996, what die set are you using and what is your loading process?

                          Comment

                          • #28
                            J-cat
                            Calguns Addict
                            • May 2005
                            • 6626

                            How is more flare going to help if his seater is too tight?

                            Comment

                            • #29
                              'ol shooter
                              Veteran Member
                              • Mar 2011
                              • 4646

                              Originally posted by J-cat
                              Lubing the case mouth encourages bullet setback. Friction is desirable in metallic cartrige reloading.
                              In practice, I have not had any issues so far. Must be good crimps.
                              sigpic
                              Bob B.
                              (\__/)
                              (='.'=)
                              (")_(")

                              Comment

                              • #30
                                J-cat
                                Calguns Addict
                                • May 2005
                                • 6626

                                Crimp does not prevent bullet setback.

                                Comment

                                Working...
                                UA-8071174-1