Unconfigured Ad Widget

Collapse

Ears are ringing....

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • #16
    pdq_wizzard
    Veteran Member
    • May 2008
    • 3813

    Originally posted by ElDub1950
    May I ask what primers you were using?

    I crunched 2 primers early on that apparently dropped in sideways but they just got smashed up.
    I would like to know this also, I have mangled primers so bad that they fall apart but (knocks on wood) I have never had one go off.

    and I don't know but I think everyone of these has been on a Dillon.
    Q: What was the most positive result of the "Cash for Clunkers" program?
    A: It took 95% of the Obama bumper stickers off the road.

    Originally posted by M. Sage
    More what? More crazy?
    You live in California. There's always more crazy. It's a renewable resource.

    Comment

    • #17
      Jeymz
      Member
      • Nov 2012
      • 292

      I had a primer go off during seating due to a crimped primer pocket that I missed (shame on me). This was a LRP for 308. I wear glasses so eye protection was good. But no ear protection so my ears rang for a good 5-10mins.
      I was scared my neighbors would think a shot went off.
      They know I lift weights so I started banging my 45lb plates around to make it seem like I dropped something lol.

      Comment

      • #18
        gixxnrocket
        Member
        • Jan 2011
        • 407

        Good morning.. err.. (12 hours later)
        Ears are still ringing a little bit.

        The primers were Winchester Large Pistol. I've never had an issue with these.

        Comment

        • #19
          Sunday
          Calguns Addict
          • Jan 2010
          • 5574

          The process didn't feel different?
          California's politicians and unionized government employees are a crime gang that makes the Mexican drug cartels look like a Girl Scout Troop in comparison.

          Comment

          • #20
            knucklehead0202
            Veteran Member
            • Aug 2008
            • 4087

            In a Dillon? Impossible!

            Comment

            • #21
              CGT80
              Veteran Member
              • Jul 2008
              • 2981

              I have smashed or dented a number of primers on a 550 buck luckily haven't set any off. I don't force the press, and I have been lucky. I have worn my electronic muffs with my phone plugged into them for music, since the case-feeders can be a bit noisy right above my ears. I have sensitive ears anyway and have enough hearing damage already. My over the ear headphones block some sound, but I don't know if it would make much difference if a primer went off. They do take the edge off the brass rattling around. They sound better than the muffs for audio quality.

              My ears started to ring 15 years ago and have only gotten worse, so I know how that feels. Ear protection is not a bad idea. For a reloading press, you will only likely need it about as often as you actually need a seat belt in a car, but you never know when an accident may have a lasting effect on you. It would have really been bad to blow a whole tube of primers. I use mostly CCI, Winchester, and wolf/tula primers.
              He who dies with the most tools/toys wins

              Comment

              • #22
                Jet Setter
                Calguns Addict
                • Aug 2012
                • 5348

                Good thing you had your 'eyes' on. It has happened to a friend of mine on an Hornady AP. It certainly gets your blood flowing. Glad you are OK.
                *********************
                WTS:
                1. PW 800+ Hydro Multispeed (just the hydraulic unit that also works with Spolar press)
                2. PW 800B converted to 800C (12 gauge) with lots of accessories and upgrades
                3. Hornady 366 (12 gauge)

                Comment

                • #23
                  bigedp51
                  Member
                  • Dec 2009
                  • 263

                  I have been reloading for over 46 years and still have my 1973 Rockchucker press I got after getting out of the military. And I seat my primers the old fashioned way one at a time and never had a single problem with a primer.



                  And I thought the RCBS priming tool was a step up from from the old Lee tools.



                  I also drive a Ford Escape with the smallest four cylinder engine made with a six speed transmission and I get over 28 miles to the gallon.. (speed kills)

                  Slow down and get out of the fast lane and be a cool cat............

                  And don't listen to Rap music when you reload.
                  (the reason your primer went off was because you lost the beat and pulled the handle out of tempo)



                  Or you can turn back the clock and reload to Iron Butterfly "In A Gadda Da Vida" and prime your cases during the drum solo.



                  1968 was a very good year for Bali-Hai-Wine‎..........but our M16 rifles were still jamming during the South East Asian War Games.

                  Last edited by bigedp51; 03-16-2014, 3:44 AM.

                  Comment

                  • #24
                    Sticky
                    Junior Member
                    • Dec 2013
                    • 92

                    One of the reasons I still load old school on a rockchucker, priming by hand one at a time. It gives me better 'feel' of each step along the way and I've never had a primer detonate in the Lee Autoprime... lol
                    Jack of all trades, master of few. Latest endeavor is building guns.. dang this is fun!!

                    Lifetime NRA Member
                    Avid archer and firearm enthusiast

                    Comment

                    • #25
                      bruce381
                      Senior Member
                      • Feb 2009
                      • 2454

                      make sure a Small primered case did not slip into your stash, blew 2 on my dillion from Small primer pockets.

                      Comment

                      • #26
                        Wrangler John
                        Senior Member
                        • Oct 2009
                        • 1799

                        I gave up trying to prime on progressive presses, except the RCBS Pro 2000 that uses the primer strips. My Hornady L&L was a complete disaster when it came to priming, jams, squashed primers, broken feed parts, even a broken drive dog. Those indexing pawls would get out of adjustment and not place the case in line with the primers - another squash. (All the progressives have one or more deficiencies no matter the brand.) So, I prime on the RCBS with new unprimed cases, but prefer to size and deprime fired brass on a single stage, then clean pockets and tumble clean the brass (I use Hornady's One Shot Lube even to size with a carbide die), then prime using an RCBS APS Hand Priming Tool.

                        I do not use any priming tool that has a tubular feed for several reasons. The tubes place the column of primers atop one another making a chain detonation easier. The tubes themselves are prone to collect primer residue that can flash under just the right circumstances, and unless the press and all its parts are grounded to an earth ground, static electricity can build up and discharge. You do not want to walk across a carpeted floor and touch a loaded primer tube for obvious reasons. That's why we also ground ourselves when installing computer mainboards and CPU's, etc, a little static discharge goes a long way. Hornady includes a safety tube to place over the primer feed tube to direct a detonation upward, a concession to the possibilities.

                        For the same reasons I do not use priming tools with large plate type primer flippers that feed loose primers into the tool.

                        That's also why the cautious handloader always puts the plastic or rubber cover on the powder measure reservoir. A primer detonation that reaches an open powder measure could compound the problems. After filling the reservoir, cap the powder canister and remove it from the bench, preferably to a powder magazine or covered box.

                        Those CCI Primer Strips hold each primer separately, with a degree of isolation of the next in-line primer provided by the feed mechanism, which reduces chances of a mass detonation. The plastic strips are themselves electrical insulators, unlike aluminum or other metallic tubes. The strips are also loaded individually containing 25 primers, with the ability to couple another strip before the first is depleted. That way no more than a maximum of 50 primers are exposed at any one time. Contrast that with a loaded tube that contains up to several hundred. The strips can be loaded with any brand, size or strength of primers.

                        So there's my nanny advice for the day.

                        Comment

                        • #27
                          stilly
                          I need a LIFE!!
                          • Jul 2009
                          • 10685

                          Originally posted by Wrangler John
                          I gave up trying to prime on progressive presses, except the RCBS Pro 2000 that uses the primer strips. My Hornady L&L was a complete disaster when it came to priming, jams, squashed primers, broken feed parts, even a broken drive dog. Those indexing pawls would get out of adjustment and not place the case in line with the primers - another squash. (All the progressives have one or more deficiencies no matter the brand.) So, I prime on the RCBS with new unprimed cases, but prefer to size and deprime fired brass on a single stage, then clean pockets and tumble clean the brass (I use Hornady's One Shot Lube even to size with a carbide die), then prime using an RCBS APS Hand Priming Tool.

                          I do not use any priming tool that has a tubular feed for several reasons. The tubes place the column of primers atop one another making a chain detonation easier. The tubes themselves are prone to collect primer residue that can flash under just the right circumstances, and unless the press and all its parts are grounded to an earth ground, static electricity can build up and discharge. You do not want to walk across a carpeted floor and touch a loaded primer tube for obvious reasons. That's why we also ground ourselves when installing computer mainboards and CPU's, etc, a little static discharge goes a long way. Hornady includes a safety tube to place over the primer feed tube to direct a detonation upward, a concession to the possibilities.

                          For the same reasons I do not use priming tools with large plate type primer flippers that feed loose primers into the tool.

                          That's also why the cautious handloader always puts the plastic or rubber cover on the powder measure reservoir. A primer detonation that reaches an open powder measure could compound the problems. After filling the reservoir, cap the powder canister and remove it from the bench, preferably to a powder magazine or covered box.

                          Those CCI Primer Strips hold each primer separately, with a degree of isolation of the next in-line primer provided by the feed mechanism, which reduces chances of a mass detonation. The plastic strips are themselves electrical insulators, unlike aluminum or other metallic tubes. The strips are also loaded individually containing 25 primers, with the ability to couple another strip before the first is depleted. That way no more than a maximum of 50 primers are exposed at any one time. Contrast that with a loaded tube that contains up to several hundred. The strips can be loaded with any brand, size or strength of primers.

                          So there's my nanny advice for the day.
                          This is the exact reason why I purchased the RCBS APS universal handprimer setup and the aps strip loader and strips. Aint used it yet, but today is the day hopefully...
                          7 Billion people on the planet. They aint ALL gonna astronauts. Some will get hit by trains...

                          Need GOOD SS pins to clean your brass? Try the new and improved model...



                          And remember- 99.9% of the lawyers ruin it for the other .1%...

                          Comment

                          • #28
                            gixxnrocket
                            Member
                            • Jan 2011
                            • 407

                            Good God! Rap... really? Sorry not my cup of tea to say the least.
                            Reloading music is another thread.
                            Anytime I'm throwing powder I prefer silence anyway.
                            My current pistol reload process is:
                            1. decap on a single stage
                            2. Wet tumble
                            3. Finger lube every 4th to 8th case
                            4. Size/powder/seat/crimp
                            5. Clean/plug and final inspect
                            6. Shoot
                            Rinse/repeat
                            Am I correct to assume dillons priming system is still not fixed? This is the first time I've had this issue. I'd also prefer not to repeat the experience. Is there any fix outside of hand priming the brass before the progressive? I'm touching and inspecting the brass several times as it is. Any more and I could probably lose the time savings and go back to the single stage.
                            More weight on the plastic pushrod? I currently have a .45 acp case on top. I could push a bullet down to the flash hole I guess. Thoughts?

                            Comment

                            • #29
                              bigedp51
                              Member
                              • Dec 2009
                              • 263

                              Originally posted by gixxnrocket
                              Good God! Rap... really? Sorry not my cup of tea to say the least.
                              Reloading music is another thread.
                              Let me guess, you were abducted by little gray aliens and they removed your funny bone and the humor portion of your cerebral cortex.

                              IT WAS A JOKE

                              Comment

                              • #30
                                M1NM
                                Calguns Addict
                                • Oct 2011
                                • 7966

                                Picture 3 looks like the primer was sitting flat but it or the shell were out of alignment. The press should have been harder to operate while crushing the primer than when just seating it.

                                Comment

                                Working...
                                UA-8071174-1