Unconfigured Ad Widget

Collapse

odd issue with sizing 9mm

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • kielbasavw
    Senior Member
    • Aug 2011
    • 1611

    odd issue with sizing 9mm

    First time reloading 9mm and first time using a carbide die.

    Im getting odd teeth marks on the very edge of the brass sfter sizing. Im not sure if its an issue with a fluted chamber from my p7m8, or what.

    I set the die 1/8 turn away from shell holder, almost every brass gets the marks, I messed around with the die, and I very seldom get the marks while 3/4 turns out away from shell holder. Unsure if this will cause chambering problems, or if the marks on the brass will be a problem to begin with.

    Using rcbs carbide die, but the carbide is a little different then most dies, its a full length sleeve piece of carbide, instead of the little short ring.



  • #2
    XVIga_Rob
    Senior Member
    • May 2012
    • 2354

    Have you checked for debris in the die? I would remove the decapping pin and inspect/clean the inside of the die.

    Per the instructions, the die should just touch the top of the shell holder, when it is at the top of the stroke.

    I use the same die's and have never had this issue.

    Comment

    • #3
      kielbasavw
      Senior Member
      • Aug 2011
      • 1611

      Per instructions carbide die should never touch shell holder

      Comment

      • #4
        Bastard
        • Jul 2009
        • 2209

        my guess would be that the brass is hitting the top of the die, possibly the decapping rod is too far down but I would have to look at the die & the set up.

        does your press cam over, are you setting you die with the arm all the way down or are you verifying that the ram is at the top of its upward stroke?

        I am also using the RCBS carbide die for my 9mm & was having issues not removing the case bulge from not being able to set the die low enough in my progressive. the solution that I use it the Lee carbide factory crimp die... but then again I always crimp as a separate stage anyway


        I would just pull the die apart & clean it, the reset the die from the beginning to start with & go from there
        Last edited by Bastard; 01-30-2014, 9:40 AM.

        Comment

        • #5
          kielbasavw
          Senior Member
          • Aug 2011
          • 1611

          Its in a rcbs rs press. Ram is up all the way. Decapping pin is set just enough to pop primers out.

          Comment

          • #6
            Bastard
            • Jul 2009
            • 2209

            watch the ram & make sure that it doesn't go back down just slightly at the end of the stroke, also know as cam over. I know that some presses do & if you are unaware it could result in the die being set wrong. or you could just load at 3/4 turn out & "plop test" your barrels which you should do anyway

            Comment

            • #7
              kielbasavw
              Senior Member
              • Aug 2011
              • 1611

              Never done a chamber check, I could do it bare brass, or should It have a bullet in it?

              Comment

              • #8
                Bastard
                • Jul 2009
                • 2209

                it should have a bullet in it, but assuming that you haven't expanded the case mouth... no on second though, seated & crimped then plop tested

                Comment

                • #9
                  mark501w
                  Senior Member
                  • Apr 2011
                  • 1699

                  Pull your decamping rod & look inside your die.

                  Comment

                  • #10
                    kielbasavw
                    Senior Member
                    • Aug 2011
                    • 1611

                    Would whats happening cause any issues if I just left it? Think it could be because the brass was shot with a flutted chamber?

                    I dont see how it would be bottoming out inside the die

                    Comment

                    • #11
                      mark501w
                      Senior Member
                      • Apr 2011
                      • 1699

                      Here's mine P7 reloads a little nicked up but, nothing unusual . Do they look like that before sizing?
                      Last edited by mark501w; 06-19-2014, 11:27 AM.

                      Comment

                      • #12
                        Bastard
                        • Jul 2009
                        • 2209

                        the more I think about it, the more I think there is something in the die... like mark said pull the decapping rod look inside - take a qtip & clean it out as well

                        Comment

                        • #13
                          mark501w
                          Senior Member
                          • Apr 2011
                          • 1699

                          Heading for range to shoot those reloads to see if fluting splits cases. Be back on in a few.
                          E

                          Comment

                          • #14
                            kielbasavw
                            Senior Member
                            • Aug 2011
                            • 1611

                            I have no split cases from flutting of my p7m8.

                            My brass looks normal before sizing (other then fluting marks)

                            Comment

                            • #15
                              mark501w
                              Senior Member
                              • Apr 2011
                              • 1699

                              Then it's something in your die.

                              Comment

                              Working...
                              UA-8071174-1