Unconfigured Ad Widget

Collapse

Using lead bullets.. ? ?

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • #16
    ptroxx
    Senior Member
    • Jan 2012
    • 2259

    Ill be using 125gr 9mm and 180gr 40sw I wont be using a glock but will be using a few s&w m&p... amd hk, and a ruger ...
    Ill have to do more research on leading.. I have never used it before so not sure what to look for..
    thanks veryone for your input...

    Comment

    • #17
      stilly
      I need a LIFE!!
      • Jul 2009
      • 10685

      Originally posted by gemoose23
      You can ask for a sample of bullets from most lead bullet manufacturers.

      Then you can slug your barrel with the bullet to confirm fitment and eliminate leading.

      You would be surprised the amount of people that shoot lead cast bullets. I have reached Power Factor 170 easily with Cast bullets. Enough speed for me.
      splain this to a noob please. Is it simply a nice short way of stating that a certain weight of bullet hits a certain speed to give it a knockdown energy or FT-LB of energy to hit something with? AND if so then what is 170? 170 ft-lbs?
      7 Billion people on the planet. They aint ALL gonna astronauts. Some will get hit by trains...

      Need GOOD SS pins to clean your brass? Try the new and improved model...



      And remember- 99.9% of the lawyers ruin it for the other .1%...

      Comment

      • #18
        tiller
        Senior Member
        • Jun 2011
        • 794

        Originally posted by Bill Steele
        I generally still use the cheap Glock barrels. I have a few not cheap KKM, but ironically their tight throats and chambers lead to all sorts of chambering issues. The roomy Glocks have no such problems.



        Depends on the leading you get, but the most common will look like Stilly described above, dark grey skid marks, how thick depends on how bad the bullet fit (how much too small in diameter).

        Bullet fit is most important, lube is second. If I am pushing some serious pressure, I use gas checked lead (i.e. mainly in 10mm for me these days)


        Ok thanks... I'm going to be buying lead bullets...

        Can you guys recommend a good company? Also you say leading happens when bullets are too small... Should I be getting into .356 or . 357 for 9mm? Should I stay away from .355?
        .223 & .308 brass processing

        Comment

        • #19
          Colt562
          Calguns Addict
          • Jun 2012
          • 5271

          I was going to order my cast boolits from missouri bullet company.
          Originally posted by bruceflinch
          Tis Better, to be Overworked & Underpaid,
          Than Oversexed & Underlaid...

          Comment

          • #20
            Bill Steele
            Calguns Addict
            • Sep 2010
            • 5028

            Originally posted by tiller
            Ok thanks... I'm going to be buying lead bullets...

            Can you guys recommend a good company? Also you say leading happens when bullets are too small... Should I be getting into .356 or . 357 for 9mm? Should I stay away from .355?
            I like SNS Casting, IMO a cut above Missouri Bullet Company, although I have loaded and shot a lot of MBC's. Another good one is Penn Bullets.

            You definitely want to go bigger than .355. It is best to slug your barrel and get an accurate measure, it can save some trial and error. I had a Beretta 92FS that needed .358 to keep leading away (it slugged at .357").

            Another approach would be to see if they will send you a handfull of .356, .357, etc. and give them a try. Any leading will be pretty obvious after a few magazines.

            A little too big is better than a little too small.

            Good luck, have fun.
            When asked what qualities he most valued in his generals, Napoleon said, "give me lucky ones."

            Comment

            • #21
              Colt562
              Calguns Addict
              • Jun 2012
              • 5271

              Originally posted by Bill Steele
              I like SNS Casting, IMO a cut above Missouri Bullet Company, although I have loaded and shot a lot of MBC's. Another good one is Penn Bullets.

              You definitely want to go bigger than .355. It is best to slug your barrel and get an accurate measure, it can save some trial and error. I had a Beretta 92FS that needed .358 to keep leading away (it slugged at .357").

              Another approach would be to see if they will send you a handfull of .356, .357, etc. and give them a try. Any leading will be pretty obvious after a few magazines.

              A little too big is better than a little too small.

              Good luck, have fun.
              Dont mean to thread jack, but how do you slug a barrel for the correct fit.
              Originally posted by bruceflinch
              Tis Better, to be Overworked & Underpaid,
              Than Oversexed & Underlaid...

              Comment

              • #22
                ptroxx
                Senior Member
                • Jan 2012
                • 2259

                Originally posted by Colt562
                Dont mean to thread jack, but how do you slug a barrel for the correct fit.
                Your not jacking the thread.... this is all great info coming from great questions.. Im new to the lead bullets so it all helps...

                Comment

                • #23
                  Colt562
                  Calguns Addict
                  • Jun 2012
                  • 5271

                  Originally posted by ptroxx
                  Your not jacking the thread.... this is all great info coming from great questions.. Im new to the lead bullets so it all helps...
                  ok, yeah Im researching lead bullets as well.
                  Originally posted by bruceflinch
                  Tis Better, to be Overworked & Underpaid,
                  Than Oversexed & Underlaid...

                  Comment

                  • #24
                    IrishJoe3
                    Veteran Member
                    • Feb 2009
                    • 3804

                    I use lead cast in my 1911A1 .45 ACP and .40 S&W XD, as well as .45-70. Shoots great through all, MUCH cheaper to load. The only issue has been leading, which really isn't much of an issue. Looking down the bore it looks a little like a crayon smear. All it takes is a little more elbow grease and you're good to go.

                    Speaking of which....my local gun shop told me Bear Creek is out of business, is that true?!

                    Edit to add : last time I bought lead cast, they ran me $45 for 500. Plated were $70ish for 500. Jacketed were over $100 for 500.
                    Urban legends are a poor basis for making public policy.

                    Comment

                    • #25
                      gemoose23
                      Senior Member
                      • Jun 2009
                      • 1079

                      Originally posted by stilly
                      splain this to a noob please. Is it simply a nice short way of stating that a certain weight of bullet hits a certain speed to give it a knockdown energy or FT-LB of energy to hit something with? AND if so then what is 170? 170 ft-lbs?
                      Power Factor is a metric USPSA/IPSC uses for point scoring, grouped into Major (165) or Minor (125).

                      Originally posted by stolen from power factor (pistol) wiki
                      The power factor is calculated by multiplying bullet weight (in grains, 7,000 to the pound) by muzzle velocity (in feet per second), then dividing by 1000. As of 2008, a value of 165 or greater is considered major, while values below 165 are minor
                      In laymans terms... lead if sized correctly, will not lead barrels and can have sufficient fps to play gun games.

                      Fellas are hunting with their Cast boolits over on that website, shooting much faster fps with gas checks etc. Lead is your friend, if you explore lead options for practice, target, gun games, paying 30-40 bucks for 500 .45ACP 200gr SWC might turn the tide.
                      Last edited by gemoose23; 04-30-2013, 10:48 PM.
                      Hornady LnL, Dillon Precision, RCBS, Lee Precision and Lyman User
                      If You want Match or Leadless hunting Ammo check out Monolithic Munitions Yes I am a shill, friends with the owners.

                      Comment

                      • #26
                        tiller
                        Senior Member
                        • Jun 2011
                        • 794

                        So to slug it... I just take one of there bullets and pound it in my barrel? And then measure the bullet diameter?
                        .223 & .308 brass processing

                        Comment

                        • #27
                          Bill Steele
                          Calguns Addict
                          • Sep 2010
                          • 5028

                          Originally posted by Colt562
                          Dont mean to thread jack, but how do you slug a barrel for the correct fit.
                          There are a number of ways to do it, depending on what you are slugging, revolver, pistol, rifle, etc.

                          Youtube has a bunch of videos onto various approaches. The main thing is to start with a lead slug, fishing sinker, lead buck, etc. that is soft lead and is larger than the diameter of the grooves in your bore. You then force the lead object through the bore. The resultant diameter +.001" is a good place to start.

                          Make sense?

                          Good luck, have fun.
                          When asked what qualities he most valued in his generals, Napoleon said, "give me lucky ones."

                          Comment

                          • #28
                            tiller
                            Senior Member
                            • Jun 2011
                            • 794

                            Originally posted by Bill Steele
                            There are a number of ways to do it, depending on what you are slugging, revolver, pistol, rifle, etc.

                            Youtube has a bunch of videos onto various approaches. The main thing is to start with a lead slug, fishing sinker, lead buck, etc. that is soft lead and is larger than the diameter of the grooves in your bore. You then force the lead object through the bore. The resultant diameter +.001" is a good place to start.

                            Make sense?

                            Good luck, have fun.
                            Could this be done with a plated bullet?
                            .223 & .308 brass processing

                            Comment

                            • #29
                              gemoose23
                              Senior Member
                              • Jun 2009
                              • 1079

                              Originally posted by tiller
                              Could this be done with a plated bullet?
                              you'll want to use softer lead so that it will conform to your barrels size, after sizing in your barrel. remove and use a micrometer to measure size.

                              Try calling for bullet samples in your calibers: http://www.laser-cast.com/index.html or http://www.precisionbullets.com/

                              I have used lasercast lead bullets that I purchased from Sportsman warehouse a long time ago. After finding out slugging my barrel later on and it turned out to be a good fitment. Which explained why they never leaded my barrel.

                              Last edited by gemoose23; 04-30-2013, 11:02 PM.
                              Hornady LnL, Dillon Precision, RCBS, Lee Precision and Lyman User
                              If You want Match or Leadless hunting Ammo check out Monolithic Munitions Yes I am a shill, friends with the owners.

                              Comment

                              • #30
                                tiller
                                Senior Member
                                • Jun 2011
                                • 794

                                Originally posted by gemoose23
                                you'll want to use softer lead so that it will conform to your barrels size, after sizing in your barrel. remove and use a micrometer to measure size.

                                Try calling for bullet samples in your calibers: http://www.laser-cast.com/index.html or http://www.precisionbullets.com/

                                I have used lasercast lead bullets that I purchased from Sportsman warehouse a long time ago. After finding out slugging my barrel later on and it turned out to be a good fitment. Which explained why they never leaded my barrel.

                                Got it! Thanks
                                .223 & .308 brass processing

                                Comment

                                Working...
                                UA-8071174-1