location? if youre close, you can drop by and check out my setup. I have single-stage and progressive presses.
Unconfigured Ad Widget
Collapse
|
|
|
|
|
|
|
|
Interested in reloading, please help!
Collapse
X
-
Buy a Dillon and in ten years when you sell it you will get more for it than you paid for it. That's a real value.
And you will shoot more, but you will save money.
Reloading is its own reward. I find it relaxing and also interesting. I also think its pretty eaqsy to turn out world class ammo once you understand what you need to do to prep your brass and what bullets to buy.
And soon Ammo will be regulated in California and the USA.
So do it now before Dillon is out 1 year on deliveries.I love America for the rights and freedoms we used to have.Comment
-
I just came up with this so it may or may not work:
For every pistol cartridge you want to reload add 1.5
For every cast bullet you are willing to use over a jacketed bullet add 1.5
For every rifle round you want to reload add 1
For every match rifle round you want to reload add 3
Manufacture Factor _____
For every hour you are willing to spend per 100 rounds add 1 (if you want more than 100 rounds per hour use a proportional decimal. ~ .25 for 400 rounds per hour)
Time Factor _____
For every $100 you are willing to spend on reloading equipment add 1
Tool Cost _____
Manufacturing Factor / Time Factor = Tool Cost
I reload .357 .45 .308 .223 and .30-06. I use cast in .357 and .45 and I want match .30-06 and match .223. So my manufacturing factor is 15. I require about a 200 rounds per hour output. My tool cost should be around $3000 and in fact that is about correct. I spent a little more over time but I also have a slightly higher output than 200 rounds per hour depending on cartridge.Last edited by milotrain; 12-15-2015, 5:57 PM.weg: That device is obsolete now. They replaced it with wizards.
frank: Wait a minute. There are more than one wizard? Is [are?] the wizard calibrated?Comment
-
It's definitely worth it. Find someone local to check it out.Comment
-
Definitely worth it
I'm a C&R guy so I started reloading to cut down on the cost of some of the more unique calibers: 6.5 carcano, 7.5 MAS, 11mm Mauser, etc. Now not only do I reload but cast my own bullets as well. This allows me to experiment with different bullet weights and loads. Today I was at the range with my enfield with some very light cast boolit plinking loads. Other days I'll go with some full power jacketed rounds. Reloading definitley give you many options at the range.
I started reloading over a decade ago with a good ol cheap Lee Anniversary Kit and although I've upgraded to an RCBS progressive for handgun and bought a digital scale, I still use the single stage press, powder measure, and other doodads in that kit for my rifle reloads.Comment
-
Comment
-
This worked!
Milo,I just came up with this so it may or may not work:
For every pistol cartridge you want to reload add 1.5
For every cast bullet you are willing to use over a jacketed bullet add 1.5
For every rifle round you want to reload add 1
For every match rifle round you want to reload add 3
Manufacture Factor _____
For every hour you are willing to spend per 100 rounds add 1 (if you want more than 100 rounds per hour use a proportional decimal. ~ .25 for 400 rounds per hour)
Time Factor _____
For every $100 you are willing to spend on reloading equipment add 1
Tool Cost _____
Manufacturing Factor / Time Factor = Tool Cost
I reload .357 .45 .308 .223 and .30-06. I use cast in .357 and .45 and I want match .30-06 and match .223. So my manufacturing factor is 15. I require about a 200 rounds per hour output. My tool cost should be around $3000 and in fact that is about correct. I spent a little more over time but I also have a slightly higher output than 200 rounds per hour depending on cartridge.
I don't quite know how you worked this out, but it's pretty accurate. At least it's accurate when I assume that "tool cost" does not include components. I've got a MF=24.5 on a single stage, therefore my TF is measured in geologic time.
BradComment
-
Brad,
I just took my setup now and pushed some numbers around until it worked. Tested it out with my single stage setup and tried some variations and it held together ok. It gets funny on the extreme ends, but then the making .38 special on a Lee classic with cast bullets is going to mess anything up.
weg: That device is obsolete now. They replaced it with wizards.
frank: Wait a minute. There are more than one wizard? Is [are?] the wizard calibrated?Comment
-
Start with this first...read it and then read it again. This will give you the background, general and specific knowledge/information and recipes for what you need (regardless of where you buy it from)Im thinking about starting a reload setup in my garage to cut cost of ammo but have no clue/experience about the process. Can anyone recommend if its worth the investment? looking to do .38,.357,5.56,9mm,.45acp,.40,.308.
Again have no knowledge what so ever on this so any comments help
Comment
-
I started reloading about 10 years ago. My motivation was sparked by the lack of 6.8spc ammo on the shelves of my local gun shops. I really liked that gun and the only way to keep it fed was to invest in a press and all the basic accessories to get started in my reloading adventure. I had no idea what I was getting myself into.
My first press was a single stage RCBS Rock Chucker. I bought as part of a kit that came with a scale, powder measure, and a few small accessories. I was set...I was trucking along with an unlimited amount of ammo for my 6.8.
Soon after my reloading started, my gun collection started to grow. I had custom chambered rifles such as my 6.5x55 ackley imp that I love to work up loads for. At that time, I added a few presses and thousands of dollars worth of accesories to my reloading bench. I even remodeled my entire garage around my reloading hobby.
Do I save money? I get that question alot and I always reply no, but I shoot alot more than I did before I started reloading. I will probalbly never see a return on my original investment from the equipment that I have chosen to purchase. However, if I had been content with my little Rock Chucker maybe it would be different.
My point is, everyone is different when it comes to reloading. You may be content with an inexpensive press and basic accessories or you may get bit by the relaoding bug as I did. It is a great hobby! Pick up the book "ABCs of Reloading" its a great place to start.Last edited by rosenbaumtravis; 12-18-2015, 2:31 AM.Comment
Calguns.net Statistics
Collapse
Topics: 1,870,997
Posts: 25,178,371
Members: 358,862
Active Members: 5,382
Welcome to our newest member, 1776 Arms.
What's Going On
Collapse
There are currently 30143 users online. 133 members and 30010 guests.
Most users ever online was 239,041 at 11:39 PM on 02-14-2026.


Comment