Unconfigured Ad Widget

Collapse

Reloading 45 acp problem

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • #16
    rlewpolar
    Senior Member
    • Mar 2014
    • 1447

    To answer one of the questions above, it is once fired brass and I do resize it.


    Sent from my iPhone using Tapatalk

    Comment

    • #17
      rlewpolar
      Senior Member
      • Mar 2014
      • 1447

      Originally posted by f4tweet
      It looks like the bullet was scraped in seating.

      Exactly. They are all doing that. Just tried seating a few dummy rounds after further increasing the flair and I'm still getting the problem. Think it's a problem with the seating die itself?


      Sent from my iPhone using Tapatalk

      Comment

      • #18
        orangeusa
        • Jul 2009
        • 9055

        Can you please take a picture of a flared round before crimping? With a bullet in it just before crimping?

        Comment

        • #19
          rlewpolar
          Senior Member
          • Mar 2014
          • 1447

          Ok, here is one before crimping.




          Sent from my iPhone using Tapatalk

          Comment

          • #20
            rlewpolar
            Senior Member
            • Mar 2014
            • 1447

            Top view.




            Sent from my iPhone using Tapatalk

            Comment

            • #21
              rlewpolar
              Senior Member
              • Mar 2014
              • 1447

              Quick question: do you chamfer the mouth before or after flaring? On the 9mm, always did it before and never had a problem. Wonder if deburring AFTER flaring here would help.


              Sent from my iPhone using Tapatalk

              Comment

              • #22
                Divehobo
                Senior Member
                • Apr 2010
                • 1271

                I am going to assume you are using a progressive press. Are you using the same turret block/caliber conversion kit and swapping dies or do you have one for 9mm and one for 45 acp? Issue looks like not enough belling of case. Projectile is getting shaved during seating process. You can break the loaded case apart and reuse the components less the bullet. It is likely junk. You can drop test loaded cartridge or use case gauge prior to taking to range and see if chambering is even possible. If puckered copper plating is severe, doubtful you will pass drop test.
                NRA Pistol, Rifle, CCW and Metallic Reloading instructor

                Comment

                • #23
                  rlewpolar
                  Senior Member
                  • Mar 2014
                  • 1447

                  I'm using a single stage press. I'm wondering now if the bullets themselves are out of spec. They were on sale. Wonder if somehow the plating is too thick. I've belled as far as I can with the expander die I have and the bullet goes very far in by hand.


                  Sent from my iPhone using Tapatalk

                  Comment

                  • #24
                    rlewpolar
                    Senior Member
                    • Mar 2014
                    • 1447

                    By the way, I have a case gauge here and all the rounds have all passed the drop test. This is really aggravating. I am starting to think it's either the bullet or the die itself.


                    Sent from my iPhone using Tapatalk

                    Comment

                    • #25
                      pacrat
                      I need a LIFE!!
                      • May 2014
                      • 10287

                      Bigger Fuzzier pictures would help.

                      OK, just being a jackhole.

                      Measure the expander portion of stem. It should be only .001/.002" smaller than your bullet dia.

                      Comment

                      • #26
                        LowThudd
                        Veteran Member
                        • Dec 2011
                        • 3608

                        Just thinking outside, is it possible they are .454 bullets and not .452? Did you measure them?

                        Comment

                        • #27
                          rlewpolar
                          Senior Member
                          • Mar 2014
                          • 1447

                          Originally posted by LowThudd
                          Just thinking outside, is it possible they are .454 bullets and not .452? Did you measure them?

                          Good thought. Just measured them, they are .452.




                          Sent from my iPhone using Tapatalk

                          Comment

                          • #28
                            rlewpolar
                            Senior Member
                            • Mar 2014
                            • 1447

                            Solved it! The lockring that holds the die to the press is missing a rubber O ring. The die was shifting slightly in the press and causing the bullet to go in slightly at an angle. Used the lockring from my 9mm die and it worked perfectly. That would explain the scraping. Thanks to all for trying to troubleshoot this.


                            Sent from my iPhone using Tapatalk

                            Comment

                            • #29
                              stephewc
                              Senior Member
                              • Nov 2007
                              • 1078

                              Only time I get problems like that is when I do not bell the mouth of the case enough. I had to experiment with it a few times to get my Xtreme bullets to seat without scrapping too much.

                              I found a random pic on the web of the bell/flare I'm talking about. The one on the far right is a little too much I think, but I try to just get enough bell/flare before it starts to scrape.



                              As for the messed up bullets, I just toss them into my recycling bin for brass/lead since there is no point in trying to salvage it.

                              Comment

                              • #30
                                stevec223
                                Senior Member
                                • Jul 2011
                                • 1620

                                I would just check the 200 bullets already loaded for copper flakes and clean them off... Then shoot them up.. Since you might have alittle exposed lead showing just clean your barrel well after shooting them up.. Break down 200 bullets--- hellllll nooooo... Cheers...

                                Comment

                                Working...
                                UA-8071174-1