Unconfigured Ad Widget

Collapse

Reloading 45 acp problem

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • rlewpolar
    Senior Member
    • Mar 2014
    • 1447

    Reloading 45 acp problem

    Been reloading 9mm for the last several months and things have gone very smoothly.

    Started reloading 45 acp and something seems weird to me. When I seat the bullet, feels very rough. Almost like the bullet is scraping when going into the brass.

    I dissembled some finished rounds and sure enough, the bullet is scraped, to the point that it is taking some of the copper plating off. Will this present a problem when shooting these reloads? Haven't yet tried them out yet.

    Using Berry's bullets, 230 grain, RN.

    Been using Berry's for the 9 mm also and don't get this scraping feeling.

    Using Lee dies for both calibers also.

    The only difference is that I've been using range brass for the 9mm but bought some very nice once fired 45 mm brass. Could it be that the brass is too good and not beat up like the range brass I've been using for the 9mm?

    Tried to expand the case mouths more than usual on the 45 brass but it didn't seem to help.

    Any input? Guess my real concern is the scraped copper plating on the bullets. Will it affect accuracy or worse, cause problems in the gun itself? Thanks.


    Sent from my iPhone using Tapatalk
  • #2
    f4tweet
    Senior Member
    • Oct 2005
    • 2022

    My guess is you are not belling enough, or you are seating and crimping on the same station.
    I found it best for me to seat and crimp on separate stations.
    Hope that helps.

    Comment

    • #3
      rlewpolar
      Senior Member
      • Mar 2014
      • 1447

      Reloading 45 acp problem

      I do seat and crimp in separate steps. I use a Lee die as the final step to crimp. I also belled enough so that the bullet starts easily and I also deburr the case mouth. Frankly, I'm stumped.


      Sent from my iPhone using Tapatalk
      Last edited by rlewpolar; 10-17-2015, 3:00 PM.

      Comment

      • #4
        9mmepiphany
        Calguns Addict
        • Jul 2008
        • 8075

        Weakening the integrity of the plating (breaking through it) will indeed affect the accuracy as it engages the rifling.

        The rule of thumb, if you feel additional resistance during seating, is that the case mouth isn't expanded enough.

        I wouldn't think it would be an issue with once fired, but when dealing with factory new brass, it isn't a bad idea to chamfer the inside of the case mouth before loading
        ...because the journey is the worthier part...The Shepherd's Tale

        Comment

        • #5
          9mmepiphany
          Calguns Addict
          • Jul 2008
          • 8075

          Originally posted by rlewpolar
          I also belled enough so that the bullet starts easily
          If you place a bullet into an expanded case, will the bullet stay in place when you invert the case?

          Frankly, I'm stumped.
          Have you tried the Lyman M-Expanding die?
          Last edited by 9mmepiphany; 10-17-2015, 3:12 PM.
          ...because the journey is the worthier part...The Shepherd's Tale

          Comment

          • #6
            rlewpolar
            Senior Member
            • Mar 2014
            • 1447

            Ok, tried to expand the mouth even more and it did indeed take care I the problem. Thanks. Now the question is, should I just shoot the 200 rounds I reloaded with scraped bullets or start over?


            Sent from my iPhone using Tapatalk

            Comment

            • #7
              9mmepiphany
              Calguns Addict
              • Jul 2008
              • 8075

              If you don't care about where the bullets hit the target, it is likely safe to shoot.

              I don't think it will damage your barrel. I guess it might depend on the quality of your barrel and how you feel about it.

              I'd likely just pull the bullets and reuse the ones where the plating hadn't been compromised
              ...because the journey is the worthier part...The Shepherd's Tale

              Comment

              • #8
                orangeusa
                • Jul 2009
                • 9055

                Get some calipers (Harbor Freight has them for like $12 I think).

                Measure the bullet diameter and the ID/OD of the case, the info is in Lee's book and many others.

                Take a picture of the seated bullet before crimping. That allows the smarter guys here to help. You might be surprised how some of the more expert reloaders here -J-Cat, Divernhunter, BigBronco can solve these things with a few photos.

                I have a LCT and have loaded a lot of 45ACP without issue. I always had to fiddle with crimping, but flairing - just enough to allow insertion of the bullet. New brass, old brass.

                Oh - this is new brass, are you resizing before loading? I know that sounds opposite of your problem, but try a round or two.

                Reloading is fun and relaxing. I like loading larger rounds than 9mm. They are easier to see..

                .

                Comment

                • #9
                  orangeusa
                  • Jul 2009
                  • 9055

                  Originally posted by 9mmepiphany
                  If you place a bullet into an expanded case, will the bullet stay in place when you invert the case?


                  Have you tried the Lyman M-Expanding die?
                  Good point on inverting the round.

                  WRT dies - he shouldn't need anything other than the dies he has to load 45ACP, in my opinion. Yiur suggestion might be a better die, I don't know, but 45ACP is an easy round to load.

                  .

                  Comment

                  • #10
                    f4tweet
                    Senior Member
                    • Oct 2005
                    • 2022

                    Remember, If you disassemble the cartridge, you will scrape the bullet.

                    Comment

                    • #11
                      9mmepiphany
                      Calguns Addict
                      • Jul 2008
                      • 8075

                      Originally posted by orangeusa
                      WRT dies - he shouldn't need anything other than the dies he has to load 45ACP, in my opinion. Yiur suggestion might be a better die, I don't know, but 45ACP is an easy round to load.
                      I agree, the .45ACP is much easier to reload than the 9mm.

                      I was only offering another option for folks reading. The Lyman M-die really caters to loaders of lead bullets.

                      Speaking of better dies...for folks who might be interested in other options. A friend who exclusively loads .45ACP is a huge proponent of the Redding Dual Ring Resizing die and their Micrometer Seating die
                      ...because the journey is the worthier part...The Shepherd's Tale

                      Comment

                      • #12
                        orangeusa
                        • Jul 2009
                        • 9055

                        Originally posted by 9mmepiphany
                        I agree, the .45ACP is much easier to reload than the 9mm.

                        I was only offering another option for folks reading. The Lyman M-die really caters to loaders of lead bullets.

                        Speaking of better dies...for folks who might be interested in other options. A friend who exclusively loads .45ACP is a huge proponent of the Redding Dual Ring Resizing die and their Micrometer Seating die
                        You always have good info. Thanks.

                        .

                        Comment

                        • #13
                          rlewpolar
                          Senior Member
                          • Mar 2014
                          • 1447

                          Ok, here are a few pics. The first is a typical bullet, notice a little scraping off the plating. This is typically what I am getting.

                          [IMG]http://images.tapatalk-cdn.com/15/10/17/18cbf4ea4c5c799c33a7156b86d47c22.jpg[/IM

                          The next one is an extreme case:



                          This one is what the final round looks like after crimping.




                          Sent from my iPhone using Tapatalk

                          Comment

                          • #14
                            rlewpolar
                            Senior Member
                            • Mar 2014
                            • 1447

                            Not sure first pic came through. Here it is:




                            Sent from my iPhone using Tapatalk

                            Comment

                            • #15
                              f4tweet
                              Senior Member
                              • Oct 2005
                              • 2022

                              It looks like the bullet was scraped in seating.
                              I normally open the case mouth to bell .010-.12.
                              Do what you have to do to seat the bullet cleanly.
                              Last edited by f4tweet; 10-17-2015, 4:03 PM.

                              Comment

                              Working...
                              UA-8071174-1