Unconfigured Ad Widget

Collapse

Px4 Storm Issues

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • jcalabria
    Junior Member
    • Feb 2013
    • 7

    Px4 Storm Issues

    Has anyone seen this before? My Px4 will not make it through a magazine without a FTE or a Stovepipe. The last round does not even eject from the gun after being fired. Any thoughts? Could the extractor be too tight, maybe needing to be filed down?

  • #2
    bigbearbear
    Calguns Addict
    • Jun 2011
    • 5378

    I don't have too much experience with the PX4 yet, but the PX4 9mm I rented at Reed's last Sunday worked flawlessly with their ammo (I think they were Blazer?). I shot off the entire box of 50 rounds and liked it so much I went to the counter and bought one on the spot.

    If you list the caliber and ammo brand you're using, others here might have a better idea.

    Comment

    • #3
      tenclip
      Member
      • Feb 2013
      • 245

      How new? What is the ammo? Hollowpoint or FMJ? Did you break it down after buying it and clean and re-lube everything with quality lube? At first glance without knowing any of the above, looks like a stiff recoil spring bringing it back too fast (or not getting back enough) before the round gets fully on the ramp. The PX4 system (non-compact) doesn't tilt the barrel down to meet the round like other guns so the round has a steep jump up the ramp.

      If indeed new, re-lube everything, let it sit overnight with the slide locked back to ease in the recoil spring. Then go shoot it with hot ammo (any quality hollow points or NATO or Lawman or even some Euro S&B) for 100 rounds or so and let everything relax before you go and shoot light (115gr.) non-HD rounds.
      Last edited by tenclip; 09-02-2013, 6:56 PM.
      IDPA - SSP/ESP/CCP | USPSA - Production/L10 | Personal Handgun Instructor

      Comment

      • #4
        fredridge
        Senior Member
        • Sep 2012
        • 1090

        take it in..... had same problem... everyone kept saying it was me.... took it in and my lgs had same problem. Tried it for a few weeks, then sent it in to Beretta. still waiting to get it back. been almost 2 months now.

        Comment

        • #5
          jcalabria
          Junior Member
          • Feb 2013
          • 7

          tenclip: The gun was purchased in February, and I have taken it out twice, cleaned prior to each use. I put about 100 rounds through it each trip, having to stop every 3 or 4 shots to clear the jam makes that a painful day at the range. I have tried WWB, Blazer Brass and Aluminum, and PMC ammo. Unfortunately it is not real easy to just go to the LGS and pickup many kinds of ammo these days. Ammo was 9mm FMJ 115 gr. target ammo. Between range trips I stored the gun with the slide locked open for several days at a time to try and ease the recoil spring, but that did not seem to make a difference.

          I am going to reach out to Beretta customer support like fredridge has and see where that gets me, I hate to be without it for several months, but that may just push me to go buy something else. Can't have too many guns in the safe.

          Thanks for the input guys.

          Comment

          • #6
            BrassCase
            CGN/CGSSA Contributor
            CGN Contributor
            • Dec 2011
            • 3194

            I've had mine for a couple of years in 40 SW. I've probably put 3000+ rounds through it without an issue and I've shot a variety of ammo through it includes imports. I will say though that I did notice some ammo leaves more carbon buildup around the extractor which I mechanically removed. I did have one misfire which I also later tried it in my CZ and it still wouldn't go so it is an ammo issue not a gun issue.

            Please let us know what happened so we can watch for it as well.
            I'd agree with you but then we'd both be wrong...
            NRA Certified:

            Chief Range Safety Officer
            Instructor: Basic Pistol Shooting
            Instructor: Personal Protection Inside the Home

            Comment

            • #7
              baggss
              CGN/CGSSA Contributor - Lifetime
              • Mar 2013
              • 3439

              Doesn't sound normal for the PX-4 in my experience. I have about 600 or 700 rounds of .40 through mine and never had an issue. Take it back as recommended.

              NRA Lifetime Member : CalGuns Lifetime Member : GOA Lifetime Member

              Comment

              • #8
                jimmythebrain
                Member
                • Dec 2007
                • 425

                Clean under the extractor hook really well.

                Get a good moly lube grease and grease up the block that mates with the barrel and causes the barrel to rotate. The PX4 needs a lot of grease in this area at first.

                Shoot some 124 grain 9 MM for a few hundred rounds.

                The PX4 line seems to have a very tight chamber. I have owned one in 9 MM and currently own one in 40 Caliber. When I reload I have to use my smallest diameter resizing die (of my three sets of 40 cal) to prevent failure to extract.

                Does your extracted brass have any scratch marks? These would be indications of rough spots in the barrel.

                You can try removing the barrel from the gun and seeing how easily your factory rounds drop into the barrel and then drop back out with just gravity. If there is any drag then use some Flitz type polish on the chamber. Buy a small container of Flitz as it goes a long way. Do NOT use a dremmel to reshape your barrel. Just use a smaller diameter barrel brush with some cleaning patches wrapped around the brush- put this in a low speed drill, add Flitz to the patch and polish away. I just had to do this to a Sig 1911. It solved my issues with FTF and FTE.

                I would try these first before sending my pistol back to the Beretta black hole of repairs. They can take forever sometimes to get a gun back to you.
                Last edited by jimmythebrain; 09-02-2013, 11:14 PM.

                Comment

                • #9
                  Massan
                  Senior Member
                  • Jul 2010
                  • 1042

                  Dont take this the wrong way but whats your experience as a handgunner?

                  Some novices experience a variety of malfunctions and falsely attribute it to the gun itself. I recommend having couple other people try it out, if a variety of people all experience the same/similar issue then its time to start looking at the hardware.

                  Check your magazines also. If they were not factory magazines(eg cheap gun show purchases) the springs may not be to spec and wear out faster causing misfeeds.

                  Comment

                  • #10
                    pontiacpratt
                    Senior Member
                    • Sep 2009
                    • 1663

                    I've tried to make my Storm fail: ran it dry, purposely limp wristed it, didn't clean it, etc.I cannot for the life of me get it to fail. I'm sorry you've had such a bad experience. I sent my NEOS into Beretta for warranty/recall work and had it back within a month.
                    A mugger, even an armed one, can only make a successful living in a society where the state has granted him a force monopoly.
                    -Marko Kloos

                    Comment

                    • #11
                      A-J
                      Veteran Member
                      • Dec 2011
                      • 2586

                      The only time I've had feed issues with my storm, they were all lube related. As in not enough.
                      It was not a threat. It was an exaggerated response to an uncompromising stance. I was taught never to make a threat unless you are prepared to carry it out and I am not a fan of carrying anything. Even watching other people carrying things makes me uncomfortable. Mainly because of the possibility they may ask me to help.

                      Comment

                      • #12
                        fredridge
                        Senior Member
                        • Sep 2012
                        • 1090

                        let me just say again.... I received similar advice that you are getting.

                        it is you... it is the ammo.... these guns are great... you don't understand how to use a gun etc. - while all those may or may not be true, it turned out the gun was the problem.

                        I had 6 months of serious frustration because I was told by so many it could not be the gun. I had my wife try it, same problems. Figured maybe she had shooting issues and was limp wristing it. Had the range guy try it, same problem. Was told again it was probably me.

                        Finally it was until I went out with a group of 8 people and had several of them try it with the same results that I took it in.

                        My LGS - told me I had too much grease (Froglube) and that was probably the problem, but they would take a look at it. I told them I use that much just to see if I could get the thing to work right. I was trying anything to make sure it wasn't me.

                        After 3-4 weeks of having it, cleaning, testing, and trying different things they determined it was the gun.

                        I am not saying that it is definitely the gun in your case and that your ammo or style of use isn't the problem.

                        What I am saying is that IT IS POSSIBLE FOR THE GUN TO BE THE PROBLEM.

                        have a few others try it and then if still a problem take it in.

                        Comment

                        • #13
                          SilverTauron
                          Calguns Addict
                          • Jan 2012
                          • 5699

                          Originally posted by jcalabria
                          Has anyone seen this before? My Px4 will not make it through a magazine without a FTE or a Stovepipe. The last round does not even eject from the gun after being fired. Any thoughts? Could the extractor be too tight, maybe needing to be filed down?

                          http://www.youtube.com/watch?v=YZxQf...ature=youtu.be
                          My Beretta 92FS has 1100 rounds though it with precisely zero failures to date.A malfunctioning weapon may be acceptable for a 1911s with less then 500 rounds,but not a Beretta.Send that defective piece back to Maryland for service forthwith.
                          Last edited by SilverTauron; 09-03-2013, 10:44 AM.
                          The more prohibitions you have, the less virtuous people will be.
                          The more subsidies you have, the less self reliant people will be.
                          -Lao-Tzu, Tau Te Ching. 479 BCE

                          The 1911 may have been in wars for 100 years, but Masetro Bartolomeo Beretta was arming the world 400 years before John Browning was ever a wet dream.

                          Comment

                          • #14
                            fredridge
                            Senior Member
                            • Sep 2012
                            • 1090

                            I laughed...but seriously - is that common with new 1911's? haven't owned one yet, but planning on it down the road

                            Originally posted by SilverTauron
                            A malfunctioning weapon may be acceptable for a 1911s with less then 500 rounds

                            Comment

                            • #15
                              Intimid8tor
                              Calguns Addict
                              • Apr 2007
                              • 6607

                              It could be the gun. All mfg put out rough ones once in a while. Have someone else shoot it and if the problem persists try a couple different kinds of ammo. If it still happens, call Beretta and get it sent back so they can make it right.
                              Starve the beast, move to a free state.

                              Bwiese: "You are making the assumption the law is reasonable/has rationale."

                              Comment

                              Working...
                              UA-8071174-1