Unconfigured Ad Widget

Collapse

80% 2011 frames.

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • #46
    MeanJeep
    Junior Member
    • Jan 2015
    • 3

    Just my observation. Not ruffling feathers here.

    Comparing a KTO 80% frame to the 2011 80% frame, its hard to justify anything near $400 in terms of getting what you pay for. For what is put into the 2011 frame I'd SWAG $40 in bar stock material. In a production run maybe 1 hr or so of process time to 80% and 2hrs at 100% finishing etc. Not that I begrudge people a living, but that looks like one heck of a markup for 80%.

    The KTO frame is made from a billet in 2 halves and brazed together. Nice looking frame and quite obvious the mfg process and chunk of material was not cheap. Yet the price and goofy braze line don't make up for its good looking profile either. $360 is still reasonable acknowledging what it took to produce from 0%.

    Tactical Machining frame is looking pretty good too for $159. Cast and forged frames don't compare since minimal machining is designed in to reduce overall cost to the end user. Hard to beat the price point here. This or a 0% casting may be my first build.

    Decisions, decisions.

    Comment

    • #47
      sturgefish
      Junior Member
      • Nov 2011
      • 88

      Make them and sell them cheaper then Smart guy

      Comment

      • #48
        sturgefish
        Junior Member
        • Nov 2011
        • 88

        Oh wait, you cant. Im done with this thread.

        Comment

        • #49
          Gringo Bandito
          Senior Member
          • Apr 2006
          • 1835

          Originally posted by sturgefish
          Oh wait, you cant. Im done with this thread.
          Was that the online forum version of a "mic drop"? I'm out *itches!!!!....

          Comment

          • #50
            Michael Ehline

            Originally posted by cedew
            My biggest complaint is the overall cost to build. It's like a $2000 AR versus a $500 AR, only a high end shooter is going to notice or care about the difference. So, the high end stuff ends up being for like 1% of the user base and is less interesting for the vast majority. I know it's not fully about the money and more about the build, it's just that 1911/2011 builds aren't anywhere near that price point, for me (and I imagine plenty of others), where it's worth spending double to have that experience. It's one of the reasons AR builds are great, you'd almost never lose money versus buying complete. I think the biggest key to selling 1911/2011 80% frames has less to do with the frame itself and more to do with price/availability/variety of build kits. Just my 2c from what I think is an average Joe perspective.
            Man. I don't know if I am an average Joe or not. But I love having tricked out rigs. It is fun.

            Comment

            • #51
              MeanJeep
              Junior Member
              • Jan 2015
              • 3

              Sincere apologies there Sturge. Like I said; I was not trying to ruffle any feathers and nothing in my observation was meant as a personal attack. That also means there may be many out there that will take you up on your offer as fair trade as have also responded.


              Originally posted by sturgefish
              Make them and sell them cheaper then Smart guy
              I am not out here to manufacture in the market place. My opinion is only as a potential smart customer you propositioned to part with hard earned money. Not that I claim to be either....being frugal is in the eye of the beholder?


              Originally posted by sturgefish
              Oh wait, you cant. Im done with this thread.
              If I couldn't, I would not be looking at 0-80% projects and would not have made the observation as I did. At the $400 price I am motivated to start at 0% and enjoy the project. Again, Sorry that this offended you.
              Last edited by MeanJeep; 02-15-2015, 9:21 AM.

              Comment

              • #52
                Fozzie TheBear
                Senior Member
                • Mar 2013
                • 616

                Sorry, little off topic, but am I crazy for wanting to do one of these without a mill? Possibly use the rotor table method I've seen others use for 1911s.

                Comment

                • #53
                  MeanJeep
                  Junior Member
                  • Jan 2015
                  • 3

                  Fozz, it's not crazy that you want to.



                  The problem is Murphy's Law taking over where the risks are higher if you cannot maintain control of the cut in a precision manner on 3 planes at the same time. When the unforeseen happens, no amount of swear words will fix it. At least get a chunk of cold rolled steel scrap 3/4 thick stock 4-5" long to practice on and get comfortable cutting to size before committing to any frame.

                  One detail I have not read so far is where someone is cutting the frame rails on a dremel table with no mention of whether the frame top had been decked as a reference surface everything else will be relative to. Obviously success has been achieved we hear about. How many would admit their failures is anyone's guess.

                  Drilling holes should not be a problem using a fixture. Anything short of a fixture without a DRO on a mill, the risks can be exponential. I've seen the drill transfer method from one frame to another. Still cringe worthy. Even with a fixture, I'd question if the drill is intended to cut to size. Preferably the drill fixture just gets an undersized hole in the right place and is reamed to size afterwards.

                  Then again, if there is a will - there is a way.

                  Comment

                  • #54
                    bigcalidave
                    CGN/CGSSA Contributor - Lifetime
                    CGN Contributor - Lifetime
                    • Jan 2009
                    • 4489

                    Originally posted by sturgefish
                    Make them and sell them cheaper then Smart guy
                    Originally posted by sturgefish
                    Oh wait, you cant. Im done with this thread.

                    Are you kidding me?
                    ...

                    Comment

                    • #55
                      foxtrotuniformlima
                      Veteran Member
                      • Nov 2008
                      • 3465

                      you know, $ 400 isn't too bad a price if they come with a grip, trigger, mag release, etc...........
                      Anyone press will hear the fat lady sing.

                      Originally posted by Vin Scully
                      Don't be sad that it's over. Smile because it happened.
                      Originally posted by William James
                      I cannot allow your ignorance, however great, to take precedence over my knowledge, however small.
                      Originally posted by BigPimping
                      When you reach the plateau, there's always going to be those that try to drag you down. Just keep up the game, collect the scratch, and ignore those who seek to drag you down to their level.
                      .

                      Comment

                      • #56
                        ZIPP1
                        Member
                        • Jul 2012
                        • 181

                        Originally posted by sturgefish
                        Oh wait, you cant. Im done with this thread.
                        what happen?

                        Comment

                        • #57
                          MONAJI
                          Member
                          • Feb 2014
                          • 138

                          Originally posted by ZIPP1
                          what happen?
                          Long story lol,
                          no but long story short sturgefish I believe was feeling attacked when he thought he was bringing something to the table for others from a manufacturer he found and/or knows that has high quality 2011 80%ers, the impression I got is he's not doing it for profit or gain but something for fellow calgunners, even in his post he spoke of the manufacturer not himself as the provider, it wasn't the last post solely I believe but the combination of the few

                          maby he was having a particularly bad day in addition to all that, not sure but I hope that has not discouraged him from helping fellow members with information of another viable option for 2011 80%ers

                          Comment

                          • #58
                            bigcalidave
                            CGN/CGSSA Contributor - Lifetime
                            CGN Contributor - Lifetime
                            • Jan 2009
                            • 4489

                            Personally, and as the person who handles the vendor relationships of this website, it sure looks like a person trying to sell these frames. I see it all the time. If he just knew of a manufacturer, he could have posted the info.
                            ...

                            Comment

                            • #59
                              sturgefish
                              Junior Member
                              • Nov 2011
                              • 88

                              Personally I hate this forum. The mods waste their time on stuff like this.

                              Comment

                              • #60
                                Dr69er
                                Member
                                • Jan 2012
                                • 203

                                Sign me up ! I like the 2011 STI versions have been waiting a long time for this type of product to show up in a 80% version...This would make
                                a fine project for me & my son for a precision build(s)...

                                I would be Interested in a least 1 steel, 1 alloy version (maybe 2) and 1 jig/fixture for final assembly.

                                Great work on getting this off the ground.

                                Thanks.

                                Dr69er-NH/Y
                                Last edited by Dr69er; 04-09-2015, 9:53 AM.
                                **************************************************
                                Developer of the 6.5mm & 6.8mm Patriot Combat Cartridge .
                                **************************************************
                                It is up to us to defend the US Constitution & the American Way !

                                Comment

                                Working...
                                UA-8071174-1