Unconfigured Ad Widget

Collapse

ar15 selector switch problem-HELP!

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • #16
    ar15barrels
    I need a LIFE!!
    • Jan 2006
    • 57198

    Originally posted by LCU1670
    Was reading some other threads, people wrote that sometimes you need to stone the front part of the disconnector, where it meets the flat part of the trigger, to lift the back of the trigger up, so it is closer to the selector.

    Is this correct.
    That is part of disconnector TIMING.
    Don't try to re-time the disconnector unless you FULLY understand how it's supposed to interact with ALL the other parts of the fire control group.
    Stoning on the underside of the disconnector in front increases disconnecter engagement to the hammer when there is not enough.
    Stoning on the front face of the disconnector hook reduces disconnector engagement to the hammer when there is too much.
    Optimum disconnector engagement is when the hook will JUST BARELY clear the hammer when the trigger is released.
    Last edited by ar15barrels; 01-01-2014, 10:04 PM.
    Randall Rausch

    AR work: www.ar15barrels.com
    Handguns: www.handgunbarrels.com
    Bolt actions: www.700barrels.com
    Foreign Semi Autos: www.akbarrels.com
    Most work done while you wait on a scheduled shop visit.

    Comment

    • #17
      6mmintl
      Veteran Member
      • Apr 2008
      • 4822

      Put a bead of weld on the trigger or safety and file to insure safety works.

      Comment

      • #18
        LCU1670
        Veteran Member
        • Mar 2010
        • 2865

        Originally posted by ar15barrels
        That is part of disconnector TIMING.
        Don't try to re-time the disconnector unless you FULLY understand how it's supposed to interact with ALL the other parts of the fire control group.
        Stoning on the underside of the disconnector in front increases disconnecter engagement to the hammer when there is not enough.
        Stoning on the front face of the disconnector hook reduces disconnector engagement to the hammer when there is too much.
        Optimum disconnector engagement is when the hook will JUST BARELY clear the hammer when the trigger is released.
        Great explanation, thanks!
        sigpic Waterborne!

        Former: Knight of Front Sight &
        Gold Star Member

        Comment

        • #19
          LCU1670
          Veteran Member
          • Mar 2010
          • 2865

          Originally posted by 6mmintl
          Put a bead of weld on the trigger or safety and file to insure safety works.
          Thanks, I don't have a welder, so that is why I was thinking of using the jp adjustable selector switch.
          sigpic Waterborne!

          Former: Knight of Front Sight &
          Gold Star Member

          Comment

          • #20
            ar15barrels
            I need a LIFE!!
            • Jan 2006
            • 57198

            Originally posted by 6mmintl
            Put a bead of weld on the trigger or safety and file to insure safety works.
            Expanding on this for other's benefit:
            The test for proper safety engagement is that there is almost no trigger movement with the selector on SAFE.
            The weld should be added and fitted if the trigger can move more than about 0.010" while the selector is on SAFE.
            This gets done BEFORE any disconnector timing work.
            Randall Rausch

            AR work: www.ar15barrels.com
            Handguns: www.handgunbarrels.com
            Bolt actions: www.700barrels.com
            Foreign Semi Autos: www.akbarrels.com
            Most work done while you wait on a scheduled shop visit.

            Comment

            • #21
              dchang0
              Veteran Member
              • Jul 2008
              • 2772

              Originally posted by LCU1670
              Thanks, where can you safely download a blueprint? I tried a couple of times by googling, each one had some sort of spyware and had to uninstall a bunch of junk!
              This is a direct link to the original Army Ordnance print for the M16:



              Focus just on the measurements you need--locations of the three holes from the center of the front pivot pin hole. You'll probably get enough info to diagnose your problem just getting the vertical distances from the top of the lower.

              Comment

              • #22
                ar15barrels
                I need a LIFE!!
                • Jan 2006
                • 57198

                This:

                Originally posted by dchang0
                You'll get enough info to diagnose your problem just getting the vertical distances from the top of the lower.
                Randall Rausch

                AR work: www.ar15barrels.com
                Handguns: www.handgunbarrels.com
                Bolt actions: www.700barrels.com
                Foreign Semi Autos: www.akbarrels.com
                Most work done while you wait on a scheduled shop visit.

                Comment

                • #23
                  LCU1670
                  Veteran Member
                  • Mar 2010
                  • 2865

                  Originally posted by dchang0
                  This is a direct link to the original Army Ordnance print for the M16:



                  Focus just on the measurements you need--locations of the three holes from the center of the front pivot pin hole. You'll probably get enough info to diagnose your problem just getting the vertical distances from the top of the lower.
                  Thanks, picked up a caliper at harbor freight, hope its accurate.
                  sigpic Waterborne!

                  Former: Knight of Front Sight &
                  Gold Star Member

                  Comment

                  • #24
                    dchang0
                    Veteran Member
                    • Jul 2008
                    • 2772

                    Grab a calculator too--you've got a lot of simple adding and subtracting to do to translate the blueprint values into measurements you can easily take with calipers.

                    Comment

                    • #25
                      LCU1670
                      Veteran Member
                      • Mar 2010
                      • 2865

                      Measured from top: selector (top edge) ~0.529-0.528
                      tigger pin top: ~0.88-0.90
                      hammer pin top edge: ~ 0.57-0.55

                      not easy to measure with calipers, did repeatedly, this was the average.

                      Got replacement selctors from Midway USA, no help. Since I don't weld, nor do I want to try something I am unfamiliary with doing, I ordered the JP Rifles adjustable selector, heres hoping!!
                      sigpic Waterborne!

                      Former: Knight of Front Sight &
                      Gold Star Member

                      Comment

                      • #26
                        kcstott
                        I need a LIFE!!
                        • Nov 2011
                        • 11796

                        A better way to do this is to insert your pins and measure across the top and the pin then subtract half the pin diameter.

                        it looks like your selector pin is fine but your hammer and trigger pin are low.

                        Your trigger pin should be .861" to the top edge of the pin. Hammer pin should be .547" to the top of the pin.

                        Comment

                        • #27
                          dchang0
                          Veteran Member
                          • Jul 2008
                          • 2772

                          Using the blueprint I sent you and a calculator, here are the measurements from top edge of receiver (someone correct me if my calculations are incorrect):

                          selector top .526 (+/- 0.0015 of hammer pin hole)
                          trigger top .861 (+/- 0.0015 of hammer pin hole)
                          hammer top .547 (+/- 0.005 of top of receiver)

                          The tolerances for the other two holes have to be calculated off of the hammer pin hole, after the hammer pin hole has been located.

                          Selector looks good in relation to the top edge, and the hammer pin hole could just barely be good in relation to the top edge if it is actually 0.550 and not 0.570, BUT the trigger pin hole is nowhere near good in relation to the top edge and therefore puts the whole group out of spec when in relation to each other.

                          You could say the trigger pin hole is too low by: (0.88+0.90)/2=0.89, 0.89-0.861 = 0.029"

                          Now that you know what's actually wrong and how much to fix it by, you can get on with fixing it accurately. If it were me, I'd fix the trigger pin hole by having someone weld it up and re-drill it, IF the hammer pin hole is really at 0.550 and not greater than 0.552. IF the hammer pin hole is too low, then I'd weld up and redrill the selector hole at some sort of Frankensteined location so that it functions with any in-spec selector.

                          Actually, I'd recommend you take measurements in the horizontal axis too before doing anything else. There is the possibility that the receiver got rotated in the jig or something similar so that the horizontal measurements are out of spec too. (IOW, maybe your group of holes got drilled at a diagonal in relation to the top edge of the receiver.)

                          ---

                          bohoki called it first, FTW!
                          Last edited by dchang0; 01-04-2014, 10:44 AM.

                          Comment

                          • #28
                            LCU1670
                            Veteran Member
                            • Mar 2010
                            • 2865

                            Thanks for the replies. What you are saying makes sense. What a pain with my first builds, BUT I am learning a lot!!!!

                            Hapy New Year!!
                            sigpic Waterborne!

                            Former: Knight of Front Sight &
                            Gold Star Member

                            Comment

                            • #29
                              kcstott
                              I need a LIFE!!
                              • Nov 2011
                              • 11796

                              If it's a forged 7075 lower I sure as hell wouldn't weld on it. do more damage then good.

                              if it's 6061 fine weld away.
                              Last edited by kcstott; 01-17-2014, 4:23 PM.

                              Comment

                              • #30
                                LCU1670
                                Veteran Member
                                • Mar 2010
                                • 2865

                                its a billet 7075, do you think the JP Rifles adjustable selctor could make up for this?? I noticed the disconnector just passes the back of the hammer.
                                sigpic Waterborne!

                                Former: Knight of Front Sight &
                                Gold Star Member

                                Comment

                                Working...
                                UA-8071174-1