Unconfigured Ad Widget

Collapse

HELP! Buffer tube threads

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • #16
    ar15barrels
    I need a LIFE!!
    • Jan 2006
    • 57201

    Originally posted by kcstott
    Most likely the threads are not cut incorrectly they were just cut prior to anodizing.
    I have lapped many lowers where the anodizing tightened up the receiver extension thread fit beyond acceptable clearance.
    A little 320 grit clover goes a long way on this job...
    Randall Rausch

    AR work: www.ar15barrels.com
    Handguns: www.handgunbarrels.com
    Bolt actions: www.700barrels.com
    Foreign Semi Autos: www.akbarrels.com
    Most work done while you wait on a scheduled shop visit.

    Comment

    • #17
      kcstott
      I need a LIFE!!
      • Nov 2011
      • 11796

      Originally posted by ar15barrels
      I have lapped many lowers where the anodizing tightened up the receiver extension thread fit beyond acceptable clearance.
      A little 320 grit clover goes a long way on this job...
      Same here. That hard anodize grows the threads enough where the tube won't even start.

      Comment

      • #18
        Rock6.3
        Senior Member
        • Nov 2010
        • 2431

        I've seen one where the lower threads are so tight that a milspec buffer/extension will only go in 1/2 turn before it locks up.

        Comment

        • #19
          bohoki
          I need a LIFE!!
          • Jan 2006
          • 20826

          do a little work with a needle file and a razor knife to clean them down to size?

          use the razor knife (one of the small snap off blade types to chase the thread all the way down then poke the needle file in to clean up any slips go slow dont expect it to work the first go around

          Comment

          • #20
            kcstott
            I need a LIFE!!
            • Nov 2011
            • 11796

            I use a tap and lapping compound

            Comment

            • #21
              ar15barrels
              I need a LIFE!!
              • Jan 2006
              • 57201

              Originally posted by bohoki
              do a little work with a needle file and a razor knife to clean them down to size?
              There is a reason that the tribesman don't build AR's in caves with rocks and flints...
              Randall Rausch

              AR work: www.ar15barrels.com
              Handguns: www.handgunbarrels.com
              Bolt actions: www.700barrels.com
              Foreign Semi Autos: www.akbarrels.com
              Most work done while you wait on a scheduled shop visit.

              Comment

              • #22
                bohoki
                I need a LIFE!!
                • Jan 2006
                • 20826

                Originally posted by ar15barrels
                There is a reason that the tribesman don't build AR's in caves with rocks and flints...
                i saw the pic and now realize the person who threaded it did not go deep enough with the tap

                Comment

                • #23
                  wecf
                  Member
                  • Dec 2009
                  • 287

                  I'm in Calabasas and have a tap if that helps.

                  Comment

                  • #24
                    kcstott
                    I need a LIFE!!
                    • Nov 2011
                    • 11796

                    Originally posted by bohoki
                    i saw the pic and now realize the person who threaded it did not go deep enough with the tap
                    Most production guns (if not all) are not taped they are thread milled and where the threads end makes no difference to thread milling

                    Comment

                    • #25
                      kcstott
                      I need a LIFE!!
                      • Nov 2011
                      • 11796

                      Originally posted by ar15barrels
                      There is a reason that the tribesman don't build AR's in caves with rocks and flints...
                      Yeah but an AR barrel can be machined down to fit anAK trunnion I've done it.

                      Eugene Stoner was an aerospace engineer. No wonder the AR is aluminum and composite

                      Comment

                      Working...
                      UA-8071174-1