Unconfigured Ad Widget

Collapse

ar-15 trigger reset issue

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • philc
    Member
    • Mar 2011
    • 480

    ar-15 trigger reset issue

    Not sure if this it the proper forum, feel free to move as necessary....

    I'm a Newbie with an ar-15 (and newbie with terminology) who is having some issues. My trigger doesn't reset after firing. After the first shot, the bolt cycles properly, the next round gets chambered, but the trigger doesn't reset.

    One thing that I noticed (hopefully this will help to diagnose); If I hold the trigger down while pulling back on the charging handle, the trigger does not reset. But when I take my finger off of the trigger and pull the charging handle, the trigger resets properly. The issue only seem to be when I pull and hold the trigger.

    Any idea what could be causing this? If you need pictures or anything, let me know what type and I'll see if I can post them...
    United Sportsmen Range Safety Officer
    (Volunteer)
  • #2
    tujungatoes
    Calguns Addict
    • Dec 2006
    • 7942

    You have hammer follow. The disconnector is not catching the hammer when the trigger is depressed, and it's allowing the hammer to follow the bolt back into battery. Do not shoot your rifle until this is resolved. Double check your fire controll group you are probably missing the disconnector spring or have the wrong spring installed.
    Last edited by tujungatoes; 11-18-2011, 3:13 PM.
    sigpic
    Originally posted by Dr. Elky
    If your a man who wears white sunglasses, your probably a douche bag
    Originally posted by CSACANNONEER
    I've been know to cross dress and go the other way at certain events.

    Comment

    • #3
      bohoki
      I need a LIFE!!
      • Jan 2006
      • 20826

      yea its hammer follow the disconnector is not working

      i just installed one that did that occasionally i had to file a little off the bottom of the front for it to catch better

      not sure of your mechanical proficency so good luck

      Comment

      • #4
        mrdd
        Senior Member
        • Jan 2009
        • 2023

        Originally posted by philc
        Not sure if this it the proper forum, feel free to move as necessary....

        I'm a Newbie with an ar-15 (and newbie with terminology) who is having some issues. My trigger doesn't reset after firing. After the first shot, the bolt cycles properly, the next round gets chambered, but the trigger doesn't reset.

        One thing that I noticed (hopefully this will help to diagnose); If I hold the trigger down while pulling back on the charging handle, the trigger does not reset. But when I take my finger off of the trigger and pull the charging handle, the trigger resets properly. The issue only seem to be when I pull and hold the trigger.

        Any idea what could be causing this? If you need pictures or anything, let me know what type and I'll see if I can post them...
        Can you describe exactly what you mean by "the trigger does not reset"? There are two different situations:

        1) The hammer does not catch on the disconnector and follows the bolt carrier back forward
        2) The hammer does catch on the disconnector, but is not released back to the trigger engagement when you release the trigger.

        Comment

        • #5
          General Urko
          Junior Member
          • Apr 2011
          • 66

          Sounds more like it doesn't even have a disconnector in it at all let alone weak or missing spring.
          If he cycles it by hand slowly and it still doesn't catch... yeah.
          Sometimes people forget all the parts needed if they haven't built one before.
          EZ fix. put necessary parts in, done.

          Comment

          • #6
            Seesm
            Calguns Addict
            • Nov 2008
            • 7812

            If you make it to the Auburn area... I will fix it for you within a few minutes.

            Comment

            • #7
              negolien
              Veteran Member
              • Sep 2010
              • 4829

              sounds familiar..

              I had a similar issue with my AR-15 when I purchased it from a member here. I assumed he ground on it trying to lighten the trigger pull but /shrug might have been a bad batch of whatever cheap PoC FCG he purchased. I took it apart and reinstalled several times thinking a spring was on backwards. It wasn't. I ended up buying a SD3G trigger for $170 because I wasn't sure if it was just a cheap part or not. Works like a champ now .

              As a side note it sounds exactly like my issue. The only way you could tell without firing it was to break it in half and cycle it by hand making sure not to let the hammer smack the frame and imitating the effects of live fire if you follow me. If you didn't it would act like it was fine but if you cycled it by hand making sure the trigger was depressed while the hammer fell as it would if fired it would not reset. Since when you fire the weapon the actions faster than you can let go of the trigger if you follow me holding the trigger depressed imitates this action.
              Last edited by negolien; 11-19-2011, 3:07 AM.
              "Men sleep peacefully in their beds at night because rough men stand ready to do violence on their behalf."

              George Orwell

              http://www.AnySoldier.com

              Comment

              • #8
                philc
                Member
                • Mar 2011
                • 480

                Thanks for all of the replies. I love the community!

                Originally posted by mrdd
                1) The hammer does not catch on the disconnector and follows the bolt carrier back forward
                2) The hammer does catch on the disconnector, but is not released back to the trigger engagement when you release the trigger.
                Pulled the charging handle while holding the trigger then seperated the upper and lower: the hammer was in the "fired" position as if it "followed". So, i guess #1.

                If the symptom was #2 would the hammer still be in the "fired" position?

                Originally posted by negolien
                I assumed he ground on it trying to lighten the trigger pull
                Grounded on what part? The lower was used and fully assembled when I got it. So, maybe I should look for grinding signs and maybe replaice parts (or look for a missing dissconnector spring like tujungatoes suggested)?

                Per the second part of your post; works perfectly fine if I cycle the hammer by hand while the upper is off. The issue completely goes away without the upper attached.
                United Sportsmen Range Safety Officer
                (Volunteer)

                Comment

                • #9
                  mrdd
                  Senior Member
                  • Jan 2009
                  • 2023

                  Most likely the disconnector or disconnector spring are modified, missing or installed incorrectly.

                  Less likely the hammer is defective or modified.

                  Have you disassembled all of the fire control parts from the lower to make sure nothing is missing? Pay special attention to the disconnector and the disconnector spring.

                  Comment

                  • #10
                    philc
                    Member
                    • Mar 2011
                    • 480

                    Newbie, being a wuss. Want to make sure it is necessary before i start taking things apart. Sounds like it is a must do though. So, off to youtube i go!
                    United Sportsmen Range Safety Officer
                    (Volunteer)

                    Comment

                    • #11
                      Seesm
                      Calguns Addict
                      • Nov 2008
                      • 7812

                      Send me a pic of the trigger group... I have a idea what it may be... Is the group stainless steel?

                      Comment

                      • #12
                        creampuff
                        • Jan 2006
                        • 3730

                        I posted these awhile ago:

                        Comment

                        • #13
                          negolien
                          Veteran Member
                          • Sep 2010
                          • 4829

                          Ya take it apart first take. Take all the fire control group apart. Make sure the springs are on right. When I said he might have ground on it I meant the bottom of the hammer where the little notch is. No reason taking your upper off should have anything to do with the issue btw unless I' am missing something. I think the RRA FCG are pretty inexpensive if you have to go that way. I heard all the same stuff and tried it all but it wasn't until I replaced it with a whole new trigger group that it worked properly. Make sure when your testing it you keep the trigger depressed to simulate real world conditions as when it cycles under live fire it's so fast you don't let go of the trigger befor it resets if you follow. Wish I had a video camera or heck even a camera lol.

                          If I recall with it broken in half and holding the hammer so when you pull the trigger it doesn't smack the lowers frame let it go forward. Keep the trigger depressed manually move the hammer back to the rear till it locks then release the trigger. This should simulate a cycle. This should simulate your malfunction and shouldn't be reseting for you..
                          "Men sleep peacefully in their beds at night because rough men stand ready to do violence on their behalf."

                          George Orwell

                          http://www.AnySoldier.com

                          Comment

                          • #14
                            wash
                            Calguns Addict
                            • Aug 2007
                            • 9011

                            A two stage trigger is not the solution to hammer follow.

                            It might "fix" the problem but if an AR won't function with a standard trigger group, something is wrong.

                            Check your disconector spring. It should have one flared out end and that end should be pushed inside the trigger so that the spring sticks in there. If your disconnector spring does not have the flared end, you are using the wrong spring. I like to stone the edges and sides of my disconnector just enough to make sure there isn't anything sharp to hang up anywhere (this shouldn't be necessary but I do it any way). There shouldn't be any extra grinding done on any of the engagement surfaces unless someone attempted to do a trigger job. If you understand what and why they do in a trigger job, you can figure out if any of it is causing your hammer follow problem.

                            It might take some thinking to understand the problem but it is good to understand how your rifle works and how it goes together.
                            sigpic
                            Originally posted by oaklander
                            Dear Kevin,

                            You suck!!! Your are wrong!!! Stop it!!!
                            Proud CGF and CGN donor. SAF life member. Former CRPA member. Gpal beta tester (it didn't work). NRA member.

                            Comment

                            • #15
                              philc
                              Member
                              • Mar 2011
                              • 480

                              Originally posted by mrdd
                              Less likely the hammer is defective or modified.
                              PlumCrazy polymer hammer was modified to fit a CMMG 9 MM BCG.

                              Replaced entire trigger group using this thread. All seems ok now. Thanks for the help. The pics and instructions were excellent!
                              Last edited by philc; 11-28-2011, 4:17 PM.
                              United Sportsmen Range Safety Officer
                              (Volunteer)

                              Comment

                              Working...
                              UA-8071174-1