Unconfigured Ad Widget

Collapse

Ejector Fitting Problems

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • #16
    ar15barrels
    I need a LIFE!!
    • Jan 2006
    • 57200

    Originally posted by rplaw
    The rail on that side is coming in around .102-.103" depending on where I check it. At the back it's .102"

    The roll pin is oval and slightly Z-shaped now. It measure .064" across the long axis of the oval and .055" across the flat sides. I'm going to assume that means it should be about .060" - .062" in diameter if undamaged.

    I'm wondering if I'm going to have to order the pins or if I can source them locally. We have a fairly decent bearing supply place but it's for industrial applications (meaning big stuff) and I don't know if they stock or can get the tiny pins.
    Local pins are fine.
    If you were local to me, i would give them to you for free as I have a box of 100 that I'll probably not use up in my lifetime.
    Replace the pin and get a 2nd shorter one as well for the rear.
    They will measure larger than 1/16" as they have to have tension in the 1/16" hole that you drill.
    You can also use 1/4" long pins for both of them and not worry about the pin going across the disconnector hole.
    Some pins have been clearanced when the pin bisects the disconnector hole so if you have a frame with that problem, it's better to run a shorter pin than to install a pin and then clearance it for the disconnector.
    Randall Rausch

    AR work: www.ar15barrels.com
    Handguns: www.handgunbarrels.com
    Bolt actions: www.700barrels.com
    Foreign Semi Autos: www.akbarrels.com
    Most work done while you wait on a scheduled shop visit.

    Comment

    • #17
      divingin
      Veteran Member
      • Jul 2015
      • 2522

      1/16" roll pins: McMaster-Carr, Fastenal, Grainger.

      You'll probably end up with a few extras.

      Comment

      • #18
        rplaw
        Senior Member
        • Dec 2014
        • 1808

        Did some file work, the ejector now drops in by hand and no longer needs to be tapped in and pried out. Grab and give it a little wiggle and it'll come out.

        By clamping it at the back I can get it to fully seat with only the tiniest of gaps at the very rear edge. I don't like having to add pressure from a clamp to get it to go all the way down so I'm going to work on it some more until I can use just finger pressure to get it to seat. Once I get it to that point, I'll clamp and drill for the rear pin.


        What's the thinking on me using some sort of bedding compound to fill the divot up at the front? I can mask off the area and use either plastic or a release compound on the underside of the ejector and use just a drop of compound in the depression to fill it, then push the ejector in place until it hardens. I'd have full support underneath that way.
        Some random thoughts:

        Somebody's gotta be the mole so it might as well be me. Seems to be working so far.

        Evil doesn't only come in black.

        Life is like a discount bakery. Usually everything is just what you ordered. But, occasionally you come face to face with an unexpected fruitcake. Surprise!

        My Utubery

        Comment

        • #19
          ar15barrels
          I need a LIFE!!
          • Jan 2006
          • 57200

          Originally posted by rplaw
          Did some file work, the ejector now drops in by hand and no longer needs to be tapped in and pried out. Grab and give it a little wiggle and it'll come out.

          By clamping it at the back I can get it to fully seat with only the tiniest of gaps at the very rear edge. I don't like having to add pressure from a clamp to get it to go all the way down so I'm going to work on it some more until I can use just finger pressure to get it to seat. Once I get it to that point, I'll clamp and drill for the rear pin.


          What's the thinking on me using some sort of bedding compound to fill the divot up at the front? I can mask off the area and use either plastic or a release compound on the underside of the ejector and use just a drop of compound in the depression to fill it, then push the ejector in place until it hardens. I'd have full support underneath that way.
          You are over-thinking it.
          Once you have both legs pinned in, it's going to be so solid that the epoxy in the front won't really be doing anything other than causing you problems when you want to remove the ejector next time.
          Randall Rausch

          AR work: www.ar15barrels.com
          Handguns: www.handgunbarrels.com
          Bolt actions: www.700barrels.com
          Foreign Semi Autos: www.akbarrels.com
          Most work done while you wait on a scheduled shop visit.

          Comment

          • #20
            rplaw
            Senior Member
            • Dec 2014
            • 1808

            Where we are this morning:

            I made a hardwood block as a work holder. Using the block I can remove material from the inner side where it's hitting the slide. The Dyechem is so I'll know that I'm working the face flat instead of rounding it or thinning at an angle.



            After a few minutes of slow sanding, letting it cool, checking, and repeating, this is the result. Remember this is rough fit and I still have to polish it and then blue it again before I can drill for the rear pin. Plus I still need to get the pins.




            The slide runs without any interference so removing a little bit more material while polishing and rounding the corners will give me plenty of clearance in the channel.

            I almost made the nose too short. The wobbly ejector was a slight extension over the factory ejector. This one is at about the length of the wobbly ejector or maybe just a little red hair shorter.

            So, on to stoning and polishing.
            Last edited by rplaw; 10-02-2022, 7:21 AM.
            Some random thoughts:

            Somebody's gotta be the mole so it might as well be me. Seems to be working so far.

            Evil doesn't only come in black.

            Life is like a discount bakery. Usually everything is just what you ordered. But, occasionally you come face to face with an unexpected fruitcake. Surprise!

            My Utubery

            Comment

            • #21
              rplaw
              Senior Member
              • Dec 2014
              • 1808

              Originally posted by ar15barrels
              You are over-thinking it.
              Once you have both legs pinned in, it's going to be so solid that the epoxy in the front won't really be doing anything other than causing you problems when you want to remove the ejector next time.
              Understood.

              I know that some manufacturers didn't pin their ejectors. (I assume those were press fit.) That tells me that while there's some stress on the part, the shock load should be taken up by the base of the body where it sits on the frame. The pins are only there to keep it from falling out. Which, by the way, this one now does if I invert the frame and shake it.
              Some random thoughts:

              Somebody's gotta be the mole so it might as well be me. Seems to be working so far.

              Evil doesn't only come in black.

              Life is like a discount bakery. Usually everything is just what you ordered. But, occasionally you come face to face with an unexpected fruitcake. Surprise!

              My Utubery

              Comment

              • #22
                ar15barrels
                I need a LIFE!!
                • Jan 2006
                • 57200

                Originally posted by rplaw
                I know that some manufacturers didn't pin their ejectors.
                (I assume those were press fit.)
                The non-pinned ones were glued in.
                Randall Rausch

                AR work: www.ar15barrels.com
                Handguns: www.handgunbarrels.com
                Bolt actions: www.700barrels.com
                Foreign Semi Autos: www.akbarrels.com
                Most work done while you wait on a scheduled shop visit.

                Comment

                • #23
                  rplaw
                  Senior Member
                  • Dec 2014
                  • 1808

                  Saturday morning update:


                  I finally found some roll pins. I also had to buy some blueing solution, mine was dried up. The part is Parkerized but I'm not set up for that so blueing the surfaces I worked on is my only option.

                  I might be able to find some time this afternoon to get going on it again. If so, it should be back in commission by tomorrow.

                  Accurately locating the center of that rear pin hole is going to be a bear. I have to offset the pin hole center .014" behind the rear edge of the leg hole for the ejector. Too far away and the pin won't bisect the leg and it'll all be a waste. Too close and the hole will be too deep and there won't be any leg left below it. Of the 2 possibilities, this is preferred because I can always buy an extended rear leg ejector (IF I can find one) and redo the fitting to the slide.

                  No pressure!
                  Some random thoughts:

                  Somebody's gotta be the mole so it might as well be me. Seems to be working so far.

                  Evil doesn't only come in black.

                  Life is like a discount bakery. Usually everything is just what you ordered. But, occasionally you come face to face with an unexpected fruitcake. Surprise!

                  My Utubery

                  Comment

                  • #24
                    Beelzy
                    Calguns Addict
                    • Apr 2008
                    • 9225

                    That ejector looks like toast with that pug nose.
                    "I kill things for a living, don't make yourself one of them"

                    Comment

                    • #25
                      rplaw
                      Senior Member
                      • Dec 2014
                      • 1808

                      Originally posted by Beelzy
                      That ejector looks like toast with that pug nose.
                      It's actually almost twice the length of the factory ejector and mimics the wobbly ejector's length.

                      The factory ejector tossed the brass into my face. The wobbly one threw it up over my head and to the side. Of the 2, I'll take high and right every time.
                      Some random thoughts:

                      Somebody's gotta be the mole so it might as well be me. Seems to be working so far.

                      Evil doesn't only come in black.

                      Life is like a discount bakery. Usually everything is just what you ordered. But, occasionally you come face to face with an unexpected fruitcake. Surprise!

                      My Utubery

                      Comment

                      • #26
                        ar15barrels
                        I need a LIFE!!
                        • Jan 2006
                        • 57200

                        With the ejector removed from the frame, the top of the frame is flat so you can just clamp it in the mill vise.
                        Set a stop on the mill vise to locate the frame so you can remove and reinstall to the same location.
                        After that, measure from the stop surface to your ejector leg hole.
                        Then add/subtract your offset and that's where you drill.
                        It's a LOT easier with a DRO but still pretty simple if you only have handwheel scales to work with.

                        Center drill to precisely locate the starting hole and then drill.

                        Originally posted by rplaw
                        Saturday morning update:


                        I finally found some roll pins. I also had to buy some blueing solution, mine was dried up. The part is Parkerized but I'm not set up for that so blueing the surfaces I worked on is my only option.

                        I might be able to find some time this afternoon to get going on it again. If so, it should be back in commission by tomorrow.

                        Accurately locating the center of that rear pin hole is going to be a bear. I have to offset the pin hole center .014" behind the rear edge of the leg hole for the ejector. Too far away and the pin won't bisect the leg and it'll all be a waste. Too close and the hole will be too deep and there won't be any leg left below it. Of the 2 possibilities, this is preferred because I can always buy an extended rear leg ejector (IF I can find one) and redo the fitting to the slide.

                        No pressure!
                        Last edited by ar15barrels; 07-10-2021, 5:36 PM.
                        Randall Rausch

                        AR work: www.ar15barrels.com
                        Handguns: www.handgunbarrels.com
                        Bolt actions: www.700barrels.com
                        Foreign Semi Autos: www.akbarrels.com
                        Most work done while you wait on a scheduled shop visit.

                        Comment

                        • #27
                          rplaw
                          Senior Member
                          • Dec 2014
                          • 1808

                          Hooray, it's done!!!

                          After blueing. It's a horrible job and I have no idea what caused the rough areas. The surface went from being shaped on the sanding wheel to a coarse wetstone then to a medium stone and finally to a smooth finish on a soft Arkansas stone then steel wool for prepping to blue. Degreased with lacquer thinner and blued. This is my usual method and normally it works perfectly. This time I get what looks like rust bubbles. All I can think of is that Birchwood Casey changed their formula or something.

                          Anyway, it worked. Kind of.



                          Setting up for drilling. Once I had the drill where I wanted it, I drilled the hole first, then put the ejector in, clamped it, and redrilled to notch the leg. Worked perfectly.



                          Installed. I beveled the hole then used my dremel to cut the roll pins to size after starting them. Then I drove them home. I had to do the front one twice because I cut it long. No big deal because I could punch from the other side and cut it again. The back one I had to drive in until it was flush on the inside of the hammer notch, mark it with a scratch, then pull it out with pliers and cut shorter than the mark. Worked ok and it's shorter than the hammer notch is wide.



                          Inside view of the rear pin.



                          The ejector is solid with no wiggle at all. All in all, it wasn't too difficult and a I want to give a HUGE shout out and thanks to ar15barrels for his helpful advice.


                          However, the saga isn't over yet. While doing this I discovered that my plunger tube is loose. Anyone in Ventura, or close by, who has a plunger staking tool I can borrow? If not, I'll buy one. Let me know please.
                          Last edited by rplaw; 10-02-2022, 7:21 AM.
                          Some random thoughts:

                          Somebody's gotta be the mole so it might as well be me. Seems to be working so far.

                          Evil doesn't only come in black.

                          Life is like a discount bakery. Usually everything is just what you ordered. But, occasionally you come face to face with an unexpected fruitcake. Surprise!

                          My Utubery

                          Comment

                          • #28
                            rplaw
                            Senior Member
                            • Dec 2014
                            • 1808

                            Originally posted by ar15barrels
                            With the ejector removed from the frame, the top of the frame is flat so you can just clamp it in the mill vise.
                            Set a stop on the mill vise to locate the frame so you can remove and reinstall to the same location.
                            After that, measure from the stop surface to your ejector leg hole.
                            Then add/subtract your offset and that's where you drill.
                            It's a LOT easier with a DRO but still pretty simple if you only have handwheel scales to work with.

                            Center drill to precisely locate the starting hole and then drill.
                            Mill? Digital Readout? You must think I have a machine shop or something.

                            I did this by scribing crossing lines where the hole should be then mounting the frame on a platform that I could clamp in my drill press. Before doing that I triple checked that the table was square to the drill column then stuck the clamping platform into the vise.

                            Tap, tap, tap, tap with a small hammer. Adjust, adjust, adjust. Tap, tap, tap some more until I get it where it should be located when I lower the bit and touch the frame. Throw a prayer to heaven and drill. Worst comes to worst, I'll have a hole in my frame that does nothing. And I can always try again in front of the leg if I screw up.

                            Luckily, fortune favored an old fool this time.

                            This is my drill press and vise where I did all the work on this. Note all the sawdust and junk everywhere, this is definitely NOT a "machine shop."

                            Dig those wooden washers on the bolts holding the vise down? $29.95 plus shipping and handling and I'll make you a set of 4 for your very own. They even come in tactical black as an option.

                            Last edited by rplaw; 10-02-2022, 7:21 AM.
                            Some random thoughts:

                            Somebody's gotta be the mole so it might as well be me. Seems to be working so far.

                            Evil doesn't only come in black.

                            Life is like a discount bakery. Usually everything is just what you ordered. But, occasionally you come face to face with an unexpected fruitcake. Surprise!

                            My Utubery

                            Comment

                            • #29
                              ar15barrels
                              I need a LIFE!!
                              • Jan 2006
                              • 57200

                              Originally posted by rplaw
                              After blueing. It's a horrible job and I have no idea what caused the rough areas. The surface went from being shaped on the sanding wheel to a coarse wetstone then to a medium stone and finally to a smooth finish on a soft Arkansas stone then steel wool for prepping to blue. Degreased with lacquer thinner and blued. This is my usual method and normally it works perfectly. This time I get what looks like rust bubbles. All I can think of is that Birchwood Casey changed their formula or something.

                              Anyway, it worked. Kind of.

                              Try brake cleaner instead.
                              Lacquer thinner can be slightly oil based and any oil stops bluing from working.
                              Randall Rausch

                              AR work: www.ar15barrels.com
                              Handguns: www.handgunbarrels.com
                              Bolt actions: www.700barrels.com
                              Foreign Semi Autos: www.akbarrels.com
                              Most work done while you wait on a scheduled shop visit.

                              Comment

                              • #30
                                ar15barrels
                                I need a LIFE!!
                                • Jan 2006
                                • 57200

                                Originally posted by rplaw
                                I did this by scribing crossing lines where the hole should be then mounting the frame on a platform that I could clamp in my drill press. Before doing that I triple checked that the table was square to the drill column then stuck the clamping platform into the vise.

                                Tap, tap, tap, tap with a small hammer. Adjust, adjust, adjust. Tap, tap, tap some more until I get it where it should be located when I lower the bit and touch the frame. Throw a prayer to heaven and drill.
                                Next time, take a center punch to your crossed lines so you have a nice solid dimple.
                                When you drop the spinning drill bit into the center punch mark, the drill bit will pull towards the CENTER of the center punch mark (hence why it's called a center punch!).
                                Use the movement of the spinning drill bit as an indicator on which direction you need to tap-tap-tap the drill press vise until you are NOT getting any dril bit deflection as the drill bit touches down.
                                Randall Rausch

                                AR work: www.ar15barrels.com
                                Handguns: www.handgunbarrels.com
                                Bolt actions: www.700barrels.com
                                Foreign Semi Autos: www.akbarrels.com
                                Most work done while you wait on a scheduled shop visit.

                                Comment

                                Working...
                                UA-8071174-1