Unconfigured Ad Widget

Collapse

CASE TRIMMER

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • emy
    Senior Member
    • Jan 2011
    • 901

    CASE TRIMMER

    member that uses WFT , does it debur the case or you have to do the two extra step
  • #2
    huckberry668
    Senior Member
    • Feb 2007
    • 1502

    I have 2 of them, 1 in 223 and 1 in 308. I used power drill and drill press with various speeds. it doesn't debur at all and it doesn't dispense the chips very well either. Dont' believe the claim that it cuts so cleanly that you don't need to debur. the sharp edge cuts bullet jacket when you seat them. which is why I bought a Giraud.

    I alo have a RCBS Power Trimmer with 3 way cutters that does all 3 steps in one. It trims to the OAL. It's slow, noisy and the pilots don't fit every case so sometimes you have problems with the keeping brass straight or wearing out the rubber drive shaft coupling. Giraud is the best of all 3.
    GCC
    NRA Certified Pistol Instructor
    Don't count your hits and congratulate yourself, count your misses and know why.

    Comment

    • #3
      emy
      Senior Member
      • Jan 2011
      • 901

      Thank you huckberry, i was about to order two for the same caliber. I will have to save some more and just get the Giraud

      Comment

      • #4
        freonr22
        I need a LIFE!!
        • Dec 2008
        • 12955

        didnt need to debur with possumhollow for 223 in cheapy drill press @ 3000 rpm...
        sigpic
        Originally posted by dantodd
        We will win. We are right. We will never stop fighting.
        Originally posted by bwiese
        They don't believe it's possible, but then Alison didn't believe there'd be 350K - 400K OLLs in CA either.
        Originally posted by louisianagirl
        Our fate is ours alone to decide as long as we remain armed heavily enough to dictate it.

        Comment

        • #5
          huckberry668
          Senior Member
          • Feb 2007
          • 1502

          The point is, a trimmer capable of chamferring is better than the drill mount type that doesn't. saves time, bullets and fingers.
          GCC
          NRA Certified Pistol Instructor
          Don't count your hits and congratulate yourself, count your misses and know why.

          Comment

          • #6
            2shotjoe
            CGN/CGSSA Contributor
            CGN Contributor
            • Feb 2011
            • 26753

            ^ i just put my debur I'm my drill.

            Bruce wished he owned a Droid RAZR.
            Originally posted by Kestryll
            ..you're kind of a sad excuse for an attorney...
            Originally posted by Libertarian777
            ...Don't pick either side....

            Comment

            • #7
              stilly
              I need a LIFE!!
              • Jul 2009
              • 10685

              Originally posted by huckberry668
              The point is, a trimmer capable of chamferring is better than the drill mount type that doesn't. saves time, bullets and fingers.
              Yeah I am liking the idea of those all in one little power centers. zip zip done...
              7 Billion people on the planet. They aint ALL gonna astronauts. Some will get hit by trains...

              Need GOOD SS pins to clean your brass? Try the new and improved model...



              And remember- 99.9% of the lawyers ruin it for the other .1%...

              Comment

              • #8
                Psychbiker
                Senior Member
                • Jul 2009
                • 1671

                CTS trimmers are pretty great. Drill press or hand drill. Smooth cut maybe kit chamfering depending on bullets used.

                A giraurd is nice but $400+ and you still need to handle each piece of brass? I'd get a dillon 1500 trimmer (new model coming out) and mout to a press with case feeder. Granted only needed if processing large quantities. Then again if only processing small batches a $400 trimmer seems over kill in my mind.

                I plan on modding my Hornady lnl to accept the new dillon which will be $300ish. It's a beefier motor designed to convert 223 down to blackout so it's going to last.

                Comment

                • #9
                  wecf
                  Member
                  • Dec 2009
                  • 287

                  I use the WFT then hit the case on my RCBS case prep center, easier than finding/waiting/paying for the Giraud. I would love to have one though.

                  Comment

                  • #10
                    1HitaQuita
                    Member
                    • Dec 2013
                    • 251

                    I just use a drill press then my lyman case prep center. press probably takes just as long as the giraud but at 1/4 the cost. HF $69 variable speed press

                    Comment

                    • #11
                      yoitsbruce
                      Senior Member
                      • Oct 2010
                      • 766

                      i use the wtf. it leaves a slight bur i can feel but after i clean the brass of the lube through the tumbler its gone

                      Comment

                      • #12
                        bigdawg86
                        Veteran Member
                        • Mar 2012
                        • 3554

                        I just did 500 300 BLK with my WFT last night... not bad once you get the damn thing to trim to the right length. I still am looking at the Dillon as an option.

                        Question for the Giraud crowd...

                        Do you get case length variations with mixed brass since it indexes off of the shoulder?

                        My WFT was pretty ballpark but occasionally would get a wild variation (ATI stamped brass seemed to be the offender)

                        Comment

                        • #13
                        • #14
                          damndave
                          I need a LIFE!!
                          • Oct 2008
                          • 10858

                          I have owned a Forster with 3-way cutter, RCBS with 3-way cutter, WFT, CTS and Gracey trimmers.

                          I got the Gracey used and did the upgrades to it. In it for about $250 now. Best investment I could make as it blows all of those other trimmers out of the water. I couldn't bring myself to buy a $500 Giraud.

                          To answer your question, the WFT and CTS do not cut clean enough at a consistent basis to not chamfer/deburr.

                          Comment

                          • #15
                            Ferrum
                            Janitors Mop
                            CGN Contributor - Lifetime
                            • Aug 2011
                            • 4431

                            Originally posted by AlliedArmory
                            I have owned a Forster with 3-way cutter, RCBS with 3-way cutter, WFT, CTS and Gracey trimmers.

                            I got the Gracey used and did the upgrades to it. In it for about $250 now. Best investment I could make as it blows all of those other trimmers out of the water. I couldn't bring myself to buy a $500 Giraud.

                            To answer your question, the WFT and CTS do not cut clean enough at a consistent basis to not chamfer/deburr.
                            Ditto...

                            Did the mods to my Gracey and couldn't be happier! The trim length is very consistent, it's quick, doesn't kill your fingers and caliber swaps are easy.

                            No knock on Giraud... In my opinion its like comparing two high end cars, you won't go wrong with either.

                            Comment

                            Working...
                            UA-8071174-1