Unconfigured Ad Widget

Collapse

First Reloading Experience. Comments Welcome.

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • #31
    brettkeating
    Member
    • Oct 2013
    • 295

    So an update... After trying twice to get replacement parts for the RCBS hand priming tool that came with my kit, and no improvement to my issue, I finally just broke down and picked up the universal hand priming tool. That priming tool worked great, and I loaded up 50 rounds.

    Accurate's data says min load behind 150gr bullet is 48.0, and max load is 51.0. I loaded 10 each of 48.5, 49, 49.5, 50 and 50.5. I figure 10 rounds would be good to figure out around which load to fine tune. I plan to take them to the range on Wednesday morning. I'll let you all know how it goes.

    Comment

    • #32
      J-cat
      Calguns Addict
      • May 2005
      • 6626

      Originally posted by brettkeating
      I got into reloading in order to save money on ammo for my Arisaka T99. So that was the first round I attempted to reload for as well. Here is the story of my first ever reloading attempt with my RCBS rock chucker kit, plus caliper and case trimmer.

      I bought some purpose-made brass, and primed 50 of them with Remington 9.5 large rifle primers. Then on a whim, I checked the case length… and what the heck, they were 0.015" too long! Brand new brass from prvi, is there any excuse for that? So I had to trim all the cases.


      Did you check the chamber length? You didn't have to trim them


      The only powder I could find was Accurate 2700. Luckily they had reloading data for my cartridge. However, the COAL seemed all wrong. There was no way 3.175" was correct. The bullets I was loading were from Hornady (150 grain soft point), and luckily I had that manual. They claimed the COAL should be 3.000". Both must have been wrong… Loading dummy rounds with no primers or powder, I couldn't imagine how anything other than 3.075" was correct, given where the stipple cannelure was located. I went with that.

      Different bullets/different OAL. Did you establish the max OAL for your rifle using a slit case?

      The load range for AA2700 was 48.5 to 51.0, according to Accurate's data. Comparing it against the Hornady load manual, I noticed another Accurate powder was listed (4530) and Accurate's numbers seemed conservative. In any case, I aimed to load mine at around 49.7 grains of powder.

      I tried to use my RCBS powder dispenser, but I was having a lot of trouble getting better than +/- 0.4 grains of accuracy with the dispensing. Fortunately this was within range of Accurate's data, so I went with it, but I'm pretty disappointed in the consistency of this dispenser. I may need to manually weigh each charge instead in the future. But 49.7 +/- 0.4 grains should be safe.

      I attached a picture of one of my reloads vs. a Norma factory 7.7x58mm load. Any comments on the story is appreciated. Great to have this forum.
      Powder measures are not very precise. I prefer electronic dispensers like the RCBS Chargemaster.

      Comment

      • #33
        brettkeating
        Member
        • Oct 2013
        • 295

        I ended up using dippers and a trickler for this batch.

        Comment

        • #34
          brettkeating
          Member
          • Oct 2013
          • 295

          Just noticed your bold comments... boy you learn something new here every day I didn't bother with trying to get the bullet real close to the lands when seating, was just trying to use published data on case length, used a dummy round to check chambering when seating to the crimping groove, and did a visual comparison against factory loads that work well in the rifle to make sure I'm not totally off. That's the extent of how I decided on my bullet seating depth

          However, I'm intrigued by the idea of using a slit case to find a more optimal bullet seating depth... I like how it's a hacky method that doesn't require buying any new tools... but looking into it a bit more using some google-fu, I had some questions about optimizing this...

          I ended up finding a lot of folks extolling the virtues of bullet comparators, OAL gauges, etc. but I was wondering if anyone could comment on the following idea...

          Suppose I seat a bullet in the slit case using the rifle, and I measure the length from rim to tip. Then suppose I take that case, put it in the press, and adjust my seating die to just touch. Then I start lowering the seating die, pushing the bullet in a little further a bit at a time, and taking new rim-to-tip measurements until I'm happy with the distance I've backed the bullet off from the lands, like 0.02-0.04" or so. Then I lock the seating die and voila I'm ready to go. Anything wrong with that?

          Comment

          • #35
            Capt.Dunsel
            Senior Member
            • May 2011
            • 1199

            First , is your Arisaka un-molested ? ( no rechamber/rebore of chamber)
            Arisakas have really long throats , you may find that you can't even touch the lands and seat the bullet. Just the way they are. If you seat to touch the lands you might also find that they won't fit in the magazine or may not feed reliably from the magazine.

            sounds to me your on the right track , take it easy, take it slow and you'll get there.
            Bweise says "I have to say the situation was not at all helped by 22 yr old former Airsoft douches who kept touting here, "But possession is not illegal!" "

            Fighting on the internet is like being in the special Olympics , everybody wins but your still retarded.

            Librarian " Calguns is not a 'general discussion board".

            Comment

            • #36
              Witch Hunter
              Member
              • Oct 2013
              • 174

              You can do that, yes. Use a sharpie to mark the bullet, seat it to touch the lands. adjust your seater die to this length. Use an unslitted case and seat a marked bullet, does it touch? Adjust die until the bullet JUST touches the lands. Measure. Set your die to this minus .020 to start. You may have to use several cases to accomplish this, just pull em when you are done. Be advised that you will show pressure if you are touching the lands. I would bet that COL will be too long for your magazine. If so, use the mag length minus .025 as your maximum COL. Good luck.

              Comment

              • #37
                brettkeating
                Member
                • Oct 2013
                • 295

                Yes, it has not been rechambered and it shoots factory ammo from Norma fairly well. It has the chrome lined bore which is a feature of the better-made earlier ones.

                Yeah I'm not totally concerned with optimizing seating depth yet, so long as I end up with something reasonable compared to published guidelines. Basics first, but it would be a fun thing to experiment with later on.

                Comment

                • #38
                  brettkeating
                  Member
                  • Oct 2013
                  • 295

                  Alright so I shot my batch of 50 and it was a great success! The only problem I encountered was one dud primer. All the remaining 50 did very well, and I didn't see any signs of pressure issues for any of them. I shot the best group with the 50.5gr load, so on my next trip I am probably going to fine tune around that.

                  I'll post a picture of the 50.5gr group at 50 yards later on, and pictures of a spent shell from each of the different sub-batches compared to factory.

                  Thanks for the help! That rifle is a tank!

                  Comment

                  • #39
                    knucklehead0202
                    Veteran Member
                    • Aug 2008
                    • 4087

                    Originally posted by Capt.Dunsel
                    First , is your Arisaka un-molested ? ( no rechamber/rebore of chamber)
                    Arisakas have really long throats , you may find that you can't even touch the lands and seat the bullet. Just the way they are. If you seat to touch the lands you might also find that they won't fit in the magazine or may not feed reliably from the magazine.

                    sounds to me your on the right track , take it easy, take it slow and you'll get there.
                    good post, and totally true. while I haven't bothered to try that with my arisakas, when I was having my 8x56r trouble, I stuck a bullet in a case and chambered it, when I extracted it the damn thing fell right out, barely even touched lands! anyhow, glad you found your stride Brett and I hope you're enjoying that Jap warhorse, I love all of mine. I loaded some up with I don't remember how much BL-C(2) for a while, but I'm in love with that silly load I cooked up with the RL-17, it's a frickin' barn-burner and is right on the edge of unpleasant to shoot, but it hits right where I point it, when I can get the sights right. old rifles are a great reloading adventure that can be quite rewarding. i'll never be a match-grade shooter so I don't worry about owning match-grade rifles, although some of these old turkeys might shoot better than some of the goofy crap they're making nowadays.

                    Comment

                    • #40
                      brettkeating
                      Member
                      • Oct 2013
                      • 295

                      Here are pics of the 50-yard group at 50.5 grains, and the spent brass. From left to right is the factory round, and then 48.5, 49.0, 49.5, 50.0 and 50.5 in that order. There are sharpie markings on the primers. Blank is 48.5, then one dot, two dots, a line, and an X as you move up. Really don't see any difference among them myself.



                      Attached Files

                      Comment

                      • #41
                        brettkeating
                        Member
                        • Oct 2013
                        • 295

                        By the way, this rifle's front sights need big-time adjusting, and I already know that. To get this group close to the center I have to aim at the left edge of the black. This is with iron sights of course, the rifle doesn't have a scope and never will

                        Comment

                        Working...
                        UA-8071174-1