Unconfigured Ad Widget

Collapse

First Reloading Experience. Comments Welcome.

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • #16
    sl0re10
    Calguns Addict
    • Jan 2013
    • 7242

    On that; I wouldn't start in the middle for load data. Start near the bottom end and work your way up (re: only make 3 of so of each step up for testing).

    I just ran into related problems yesterday. Tons of pressure signs on some ammo that was still not in the upper 1/3 of the recommended charge.

    Comment

    • #17
      brettkeating
      Member
      • Oct 2013
      • 295

      Ok I'll take that advice. I'll keep the rounds I made, but before firing those ones, I'll make another batch. 2-3 rounds at the starting load, and then incrementally increase the charge for subsequent 2-3 rounds until I reach beyond what I had loaded for the first batch. I will hand-measure the charges. If I can't make it all the way through without any problems, I'll pull the first batch. Any advice on how to mark them? Just write on the brass with a sharpie?

      Comment

      • #18
        knucklehead0202
        Veteran Member
        • Aug 2008
        • 4087

        if you're still having problems with your powder measure, consider getting a set of dippers and see if one will weight out a charge close to what you're looking for. if you're not trying to shoot matches with it, those will be consistent enough and perhaps more so than your measure. some don't like extruded powders and will cut them, that's the grittiness you're getting when dispensing. a dipper and a trickler work well if you want to be precise.

        Comment

        • #19
          krwada
          Senior Member
          CGN Contributor
          • Jun 2013
          • 1457

          As to getting more consistent throws using your uniflow powder measure; I highly recommend you go and purchase a Uniflow Powder Baffle.

          For the very best in accuracy; you should get the powder baffle and the Redding Trickler.

          I usually underthrow all my rifle charges by a couple tenths and then trickle them up using the Redding Trickler.

          As to marking your rounds. I get a sharpie marker and place a colored dot on the primer. Since the primer gets 'popped' anyway ... this gives a very good visual of the round and you do not wind up marking your brass. Sharpie markers come in various colors .... black, blue, red, green etc....

          Comment

          • #20
            sr71brd
            Junior Member
            • Jan 2008
            • 72

            Originally posted by brettkeating
            No that's fine. I was worried about squibs too so was aiming for the middle. I stayed pretty much a full grain below the max load. It's a little tough when you only have access to one powder and one data point. Hope everything works out.
            A squib is a round w/o any powder. Just a case, primer & bullet. Starting @ minimum loads will not give you a squib round. I really think you need to read the front sections of the reloading manual you have. When you're done, read them again. You are reloading for a firearm that is 60+ yrs. old. You don't know it's history, only that it's made it this far. Don't be the one that ruins it for future generations by being careless. As far as powder dispensing, you have received good advice, follow it.

            Comment

            • #21
              BruinGuy
              Senior Member
              • Apr 2011
              • 1456

              You don't say what it is you're trying to achieve. Do you want to punch paper at 100 yards, or ring a gong at 500 yards? A great load for the latter might not be good for the former and vice versa.

              If testing for accuracy, you might consider loading more than 3 of each charge and consider how much velocity you need to get to your target depending on the range at which you will be shooting. IMHO 3 rounds isn't enough to send down range to compensate for shooter error. If you pull one, your group will seem to be bad, but you may discount then your most accurate load. A relatively light load can be very accurate at 50-100, and fall off at longer ranges, but why waste powder if you're not stretching it out? I would also start at minimum or near it and work up.
              Originally posted by CSACANNONEER
              Keep in mind that you don't have a clue.

              Comment

              • #22
                brettkeating
                Member
                • Oct 2013
                • 295

                Originally posted by sr71brd
                A squib is a round w/o any powder. Just a case, primer & bullet. Starting @ minimum loads will not give you a squib round.
                A squib is a round with insufficient power to exit the barrel, powder or no powder, and can happen with factory loads as well as reloads.

                Originally posted by sr71brd
                I really think you need to read the front sections of the reloading manual you have. When you're done, read them again. You are reloading for a firearm that is 60+ yrs. old. You don't know it's history, only that it's made it this far. Don't be the one that ruins it for future generations by being careless. As far as powder dispensing, you have received good advice, follow it.
                You're making a lot of assumptions about me and what I've read, and what I know about my own firearms.

                I come to this forum to get help and advice, which is freely given, and for that I am grateful. I have respect for the knowledge and experience I am trying to leverage. However, as you might expect anyone would, I start to bristle when people make disrespectful assumptions about me, and take on an air of superiority because of their greater experience in reloading.

                I guarantee you that my expertise in several other fields far surpasses yours.

                Other than that little complaint, I thank you and everyone else for sharing their experience and offering advice. It's great to have this forum, and I really appreciate the helpfulness!

                Comment

                • #23
                  brettkeating
                  Member
                  • Oct 2013
                  • 295

                  Originally posted by BruinGuy
                  You don't say what it is you're trying to achieve. Do you want to punch paper at 100 yards, or ring a gong at 500 yards? A great load for the latter might not be good for the former and vice versa.

                  If testing for accuracy, you might consider loading more than 3 of each charge and consider how much velocity you need to get to your target depending on the range at which you will be shooting. IMHO 3 rounds isn't enough to send down range to compensate for shooter error. If you pull one, your group will seem to be bad, but you may discount then your most accurate load. A relatively light load can be very accurate at 50-100, and fall off at longer ranges, but why waste powder if you're not stretching it out? I would also start at minimum or near it and work up.
                  I was thinking this myself… I was initially considering just verifying the safety of my original loads, but then I found that I made another mistake (my primer rod was upside down and mushed the primers) so I pulled the batch anyway. Turns out the primer rod was insufficient when placed the right way in the priming tool… it was impossible to get primers below flush, and I could remove the case with the grips fully squeezed... which is probably why I flipped it around… RCBS will be sending me a new primer rod.

                  So I will start over with a few rounds, spaced out by 0.5 grains or so, and will hand measure the powder.

                  My goal is to simply be able to use this rifle as a hunting rifle if needed, and to be able to practice shooting it so I can be proficient with it, but not break the bank on $2 per round ammunition. Accuracy at around 100 yards is pretty much the goal. I also have a Nambu T14 that I would like to eventually reload for as well, in addition to a 357 magnum revolver and a 9mm Glock, in order of priority based on the costs of ammunition. But I can recover the cost of my reloading setup within about 3-4 hundred rounds on the Arisaka alone.

                  By the way, the Arisaka is in tremendous condition, and is known to be one of the strongest bolt action rifles ever made, if not the strongest. There might not be a safer rifle to get started with reloading.
                  Last edited by brettkeating; 01-22-2014, 6:17 PM.

                  Comment

                  • #24
                    CSACANNONEER
                    CGN/CGSSA Contributor - Lifetime
                    CGN Contributor - Lifetime
                    • Dec 2006
                    • 44094

                    Originally posted by sr71brd
                    A squib is a round w/o any powder. Just a case, primer & bullet. Starting @ minimum loads will not give you a squib round. I really think you need to read the front sections of the reloading manual you have. When you're done, read them again. You are reloading for a firearm that is 60+ yrs. old. You don't know it's history, only that it's made it this far. Don't be the one that ruins it for future generations by being careless. As far as powder dispensing, you have received good advice, follow it.
                    OK, after reading your first sentence, I had to stop and reread it again to make sure I was reading it right. yea, I read it correctly and now I know that you are a the type of reloader/shooter that is very dangerous. You have shown that you have some knowledge but, not enough to know what you are talking about. Please, before you try to educate anyone, do a little more learning. A squib can have a powder charge. In fact, it could even have a full powder charge that somehow does not burn properly. Of course, it could have no charge or a partial charge too. In fact, I've had squibs from super light loads that were caused by the barrel fouling up. With a clean barrel, the loads don't squib at all. So, is a squib always due to no powder? Of course not. hell, sometimes a squib can occur for reasons other than a bad powder charge. Now, I suggest going and reading the front section of YOUR reloading manuals before trying to post like your an authority on a subject that you don't seem to have a good grasp on yet.
                    NRA Certified Pistol, Rifle, Shotgun and Metallic Cartridge Reloading Instructor
                    California DOJ Certified Fingerprint Roller
                    Ventura County approved CCW Instructor
                    Utah CCW Instructor


                    Offering low cost multi state CCW, private basic shooting and reloading classes for calgunners.

                    sigpic
                    CCW SAFE MEMBERSHIPS HERE

                    KM6WLV

                    Comment

                    • #25
                      brettkeating
                      Member
                      • Oct 2013
                      • 295

                      Originally posted by Divernhunter
                      You do not "need" to resize new brass. The most I do is run the brass into the sizing die enough to round out the mouth. I have been doing this for many years and produce excellent ammo. I have never had a round that would not chamber easy. Your ammo will be fine.

                      Beware that the accurate 4350 and the 4350 in the Hornady book are two different powders. There is also a H4350 and it is different than the other 2.

                      If you want some help with the powder measure PM me.

                      Comment

                      • #26
                        chknlyps2
                        Senior Member
                        • Apr 2011
                        • 2191

                        Originally posted by CSACANNONEER
                        OK, after reading your first sentence, I had to stop and reread it again to make sure I was reading it right. yea, I read it correctly and now I know that you are a the type of reloader/shooter that is very dangerous. You have shown that you have some knowledge but, not enough to know what you are talking about. Please, before you try to educate anyone, do a little more learning. A squib can have a powder charge. In fact, it could even have a full powder charge that somehow does not burn properly. Of course, it could have no charge or a partial charge too. In fact, I've had squibs from super light loads that were caused by the barrel fouling up. With a clean barrel, the loads don't squib at all. So, is a squib always due to no powder? Of course not. hell, sometimes a squib can occur for reasons other than a bad powder charge. Now, I suggest going and reading the front section of YOUR reloading manuals before trying to post like your an authority on a subject that you don't seem to have a good grasp on yet.
                        I have some .38 special loads that shoot good through my model 28 S&W with a 4" barrel but when you shoot them in my Taurus with a 6" barrel I got 1 squib by the 4th shot, the 3 before all came out of the barrel like an under handed pitch and lobbed in and skipped on the dirt way before the target at 25 yards. I pulled 3 of them when I got home and checked the charge. They were all within 3.2 and 3.3 grains. I shot those 3 after I re seated them and got 1 squib, the bullet was less than a half inch from making it out of the barrel. The powder was Bullseye under a 158 gr cast semi wad cutter, target load was 3.3 grains. In the Lymans 47th book (and 49th which I have now) min is 3.0 gr and max is 3.5 gr. so it goes to show that even a minimum or over load can squib under the right conditions. The barrel was clean, crisp with no leading.
                        Wanted: Spent Berdan primed Yugo 7.62x39 & 7.5x55 GP11 Swiss brass

                        Comment

                        • #27
                          brettkeating
                          Member
                          • Oct 2013
                          • 295

                          Originally posted by chknlyps2
                          I have some .38 special loads that shoot good through my model 28 S&W with a 4" barrel but when you shoot them in my Taurus with a 6" barrel I got 1 squib by the 4th shot, the 3 before all came out of the barrel like an under handed pitch and lobbed in and skipped on the dirt way before the target at 25 yards. I pulled 3 of them when I got home and checked the charge. They were all within 3.2 and 3.3 grains. I shot those 3 after I re seated them and got 1 squib, the bullet was less than a half inch from making it out of the barrel. The powder was Bullseye under a 158 gr cast semi wad cutter, target load was 3.3 grains. In the Lymans 47th book (and 49th which I have now) min is 3.0 gr and max is 3.5 gr. so it goes to show that even a minimum or over load can squib under the right conditions. The barrel was clean, crisp with no leading.
                          Thank you for that. If I see my rounds at the low end of the charge range skipping along before they hit the target, I'll be sure to move to the next charge

                          Comment

                          • #28
                            fastpowerstroker
                            Member
                            • Feb 2009
                            • 420

                            I have had to trim new brass before, sometimes half the bag! Yeah they aren't incredibly long, but they were out of spec. Just trim to the minimum then you will be good for the next loading too. As far as the powder charging problems, I do as others have suggested which is set up with a light throw, then trickle in the rest. Have to weigh each charge, but I don't load to many rifle rounds at a time. (30-50)

                            Comment

                            • #29
                              knucklehead0202
                              Veteran Member
                              • Aug 2008
                              • 4087

                              the 7.7 is pretty forgiving to load for, but some are not. with rifle cartridges, especially old funny ones it sometimes takes a bit of trial and error before finding a formula that works. I've worked up a few loads for 7.7 jap that work pretty well, but my 8x56r and 6.5 carcano loads are still in the works. the first 8x56r loads I worked up were downright bizarre. no squibs or anything like that, but I had some severe hangfires due to poor ignition. case design and load density of coarse plays into this, but before changing anything else I loaded the same case, powder, and bullet but used magnum primers. now the initial ones shot consistently when I didn't flinch from the hangfires, lol, but boy were they weird! with the mag primers, no ignition problems and despite the funky sights, were hitting where they were pointed, aside from the occasional flinch. 8x56r in an m95 carbine starts to pound you after a bit. anyhow, I'm currently loading 150gr bullets in my 7.7 jap with Alliant reloder 17, which is similar to 4350 and that's the data I used in the load workup. once I get a chrono I'd love to see what they're going because they feel and sound pretty fast and hit hard on the steel targets. recoil is stiffer than some of the 30-06's I fired that day but my cases came out squeaky-clean, as did the bore and no signs of pressure problems on any of the cases. any medium-burn rate rifle powder should be easy to get decent results from the old 7.7. I've got a bunch of manuals if you need some data.

                              Comment

                              • #30
                                brettkeating
                                Member
                                • Oct 2013
                                • 295

                                Thanks knucklehead0202. I'm also loading 150gr bullets but the only powder I have is AA2700. If you see that in any manuals let me know. I have Lyman, Speer and Hornady manuals and it only appears for this cartridge on Accurate's website.

                                Comment

                                Working...
                                UA-8071174-1