Here's my homemade recipe for an ultrasonic cleaner. Two drops of dawn dish soap, one part vinegar and three parts water. This will clean off the heavy powder and grime/oil. This is all done in hot water, 95* plus temp. When the brass comes out it will dry off quickly due to the hot water evaporating. Then off to the tumbler for a final polish. Brass always comes out clean and bright. Hope this helps you.
Unconfigured Ad Widget
Collapse
|
|
|
|
|
|
|
|
Sonic cleaner question
Collapse
X
-
So I dry them before I lube and resize, then how do you recommend I get the lube off? Back in the cleaner and repeat the process again?
As for drying the brass, is it safe to put them in the oven when there is still lead/carbon residue on and in them?Comment
-
Now what.
One thing leads to another!
This is becoming a hassle. I found this white corrosion inside the primer pockets only. Is this bad? I took a pic of only 1case but they pretty much all have this stuff, and only in the primer pockets. The ones that are almost 100% clean in the primer pocket do not have this corrosion. Oh and I used the Hornady one shot solution.
Edit: just confirmed it's inside the cases as well. It seems as if maybe the solution is still attacking the carbon?Last edited by selfshrevident; 07-10-2020, 10:31 AM.Comment
-
1/2oz solution per 20oz of water (according to the bottle). I admit that I ballpark it though. Just pour in a "splash"Comment
-
I use the Hornady One Shot Sonic Cleaner solution mixed to spec. I just bought a measuring cup for the reloading area and some jugs of distilled water and just mix a whole gallon or so at a time. No problem so far with clean out the the primer pockets but I save this process for precision ammo I am building.
I still tumble all the major crap off with a tumbler and then resize and then tumble the lube off before the sonic cleaner bath.
I use 24 grit walnut media from Harbor Freight mixed with mineral spirits and nu finish. Haven't had any stuck media issues since I switched to 24 grit. Its like 25 bucks for 25 lbs and works pretty well. They have 12 grit that I bought as well but hardly use due to media stuck in primer pockets.
When I sonic clean the brass using the Hornady stuff a quick turn with a primer pocket brush gets the last of the gunk out before I rinse and then dry.
I use a food dehydrator to dry the brass on the trays.
Kinda of a long process with tumble - lube - resize - tumble - sonic clean - rinse - dry but they look good to me and the inside and primer pockets are clean enough for me.
Once I am done with all that I pack them in bags until I am ready to load them up. Might toss them in the tumbler really quick to get them shiny again if I need to but not for too long.Comment
-
I used 50/50 water and lemon juice in my Harbor Freight ultrasonic. warm water to start and heater on for 3 x 8 minute cycles. Dump into fresh water and rinse. towel dry and let air out for a day or two. Came out very nice and insides are quite clean.

My neighbor used 100% lemon juice in his Thumler Tumbler and his results were even nicer.They say nothing is impossible. Well heck! I do the impossible everyday...
Comment
-
Having Pretty Good Luck With Ultrasonic and Baney's Best Recipe
I'm pretty new to reloading, and opted to go with an ultrasonic unit for cleaning the brass, since 1) I can use the unit for other needs, and 2) I don't have a workspace I can dedicate for reloading/cleaning/etc. Harbor Freight had a good deal at the time. I deprime before I clean, and Baney's Best recipe for cheap and clean (http://www.6mmbr.com/ultrasonic.html) works pretty well for me.
I've read some posts about using beakers in the ultrasonic unit, and I've had good luck using the 2/2.5 lb Costco containers (for mixed nuts, chocolate caramels, etc.) to hold the cases. They're no cost, and if one breaks I just toss it. They fit into the unit with plenty of side clearance.
I load my cleaning solution and the brass into the Costco container, cap it, set it in the ultrasonic unit and add clean water to the tank to roughly match the fluid height in the container. Using the container is convenient for rinsing out the different solutions, and it keeps the ultrasonic unit clean.
For pistol, I usually run around 100 cases at a time. For rifle, I run around 20 to 30 cases per batch.
I found that about 16 oz. of liquid for the initial cleaning (8 oz. each of water and vinegar) is about the right volume. Then I just add fresh water to cover the batch for each of the other steps.
I haven't yet tried anything to brighten/polish the brass, but am planning to try Lemi-Shine or other to see how they work for me.Comment
-
I also use Baney's Best cheap and clean. It works really well for me. Before I clean, I wipe down the cases with a green scotch brite pad with a little case lube on it. This allows me to resize and decap before cleaning. Cleaning removes the lube and a dehydrator from harbor freight works well or you can always use the wife's hair dryer.Comment
-
I have both a vibratory tumbler and ultrasonic cleaner, and have since began using a stainless tumbler and the results are hands down the best imo when factoring in time and labor and fits a ton of brass 100 pieces of 338 lapua and still had room. Then toss them into a cheap food dehydrator for a few hrs.Comment
Calguns.net Statistics
Collapse
Topics: 1,870,971
Posts: 25,178,133
Members: 358,862
Active Members: 5,382
Welcome to our newest member, 1776 Arms.
What's Going On
Collapse
There are currently 39589 users online. 39 members and 39550 guests.
Most users ever online was 239,041 at 11:39 PM on 02-14-2026.

Comment