Unconfigured Ad Widget

Collapse

New reloader with question.....

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • Lucky Scott
    Veteran Member
    • Dec 2008
    • 2612

    New reloader with question.....

    Okay, I have been moving toward reloading for a while now. Bought powder, bullets, brass, and primers. Then, got the dies.
    Wife picked up a reloading setup for me for christmas from a friend. Used, but in good condition. RCBS single stage for my 7mm Remington Mag.
    I dont have everything I need yet, but almost.

    Here is my first issue.
    I tried reloading a couple rounds without powder or primer. Just to try it out.
    I full length sized the used remington brass. De capped the primers, and seated a bullet. Sierra gameking 160 Gr. bullet. I mic'ed the OAL of the brass and I mic'ed the OAL of the bullet.

    My problem is the brass is collapsing. The shoulder of the brass is all wrinkled. It seems that pushing the bullet in is crushing the brass down. I measured and it looks like it is getting crushed about 40 thousand.

    I do not have a campher / de burr tool yet, is this the problem? What else would cause the brass to crush and wrinkle like that?
  • #2
    BigBronco also not a Cabinetguy
    Calguns Addict
    • Jul 2009
    • 7084

    The seating die body is most likely set too low. Raise the body up about two turns then re adjust the seating stem down to achieve the proper OAL
    "Life is a long song" Jethro Tull

    Comment

    • #3
      J-cat
      Calguns Addict
      • May 2005
      • 6626

      The seater die also crimps. Crimping is what collapses the shoulder as there is no cannelure in the bullet where the case mouth can roll into. So back off the die until it does not crimp. The way to do this is to screw the die down on an empty case. It will bottom out against the case mouth. Now back out the due half a turn. Adjust the seater stem as needed to achieve the OAL you want.

      Comment

      • #4
        Stockton
        Vendor/Retailer
        • Oct 2007
        • 1316

        If you read the instructions that came with your dies it will explain how to set them properly. Insert your shell holder. Bring your stroke all the way up. Turn your die down until it touches shell holder. Lower your stroke. Turn die down 1/4 turn and set lock ring. Bring stroke back up and it should cantilever slighty over till it stops. At that point make adjustments with seater screw.
        http://youtu.be/7Ii2kyQP-Is

        Comment

        • #5
          Lucky Scott
          Veteran Member
          • Dec 2008
          • 2612

          More info......
          Looks like the shoulder of the brass is crimped when I am using the full length die, and then gets worse when I seat the bullet. However, when I seat a bullet on brass without using the full length die, it still crushed the brass. It just did it in a more uniform pattern.

          Comment

          • #6
            Enfield47
            Calguns Addict
            • Sep 2012
            • 6385

            Originally posted by J-cat
            The seater die also crimps. Crimping is what collapses the shoulder as there is no cannelure in the bullet where the case mouth can roll into. So back off the die until it does not crimp. The way to do this is to screw the die down on an empty case. It will bottom out against the case mouth. Now back out the due half a turn. Adjust the seater stem as needed to achieve the OAL you want.
            ^^^This
            I once set up a seater die by screwing it down until it touched the shell holder, when I tried to seat the bullet, it collapsed the neck down completely. Needless to say it was a moment of D'oh! that I won't repeat again. It's part of the learning experience.

            Comment

            • #7
              Stockton
              Vendor/Retailer
              • Oct 2007
              • 1316

              Yep that seater adjustment is what throws a lot of people off first time around. Especially when dies come with crimping. He'll figure out and smooth sailing from there.
              http://youtu.be/7Ii2kyQP-Is

              Comment

              • #8
                kurac
                Veteran Member
                • Dec 2005
                • 2917

                also make sure you chamfer the case mouth, if you have a heavy burr sometimes that can cause the problem you describe. It sounds like you need to back out the seating die quite a bit though.
                www.culinagrips.com
                "custom grips for shooters by shooters"

                Comment

                • #9
                  Lucky Scott
                  Veteran Member
                  • Dec 2008
                  • 2612

                  " once set up a seater die by screwing it down until it touched the shell holder, when I tried to seat the bullet, it collapsed the neck down completely. Needless to say it was a moment of D'oh! that I won't repeat again. It's part of the learning experience."

                  That may be it. i thought you were supposed to seat the die to the shell holder, and then give it an extra 1/8 turn IN to take up slack. Instead, I should turn it OUT........

                  The whole process is a learning experience. That is okay with me, I dont mind learning. That is part of the fun. It sure is nice to get help from Cal Gunners.

                  Comment

                  • #10
                    J-cat
                    Calguns Addict
                    • May 2005
                    • 6626

                    Originally posted by Lucky Scott

                    That may be it. i thought you were supposed to seat the die to the shell holder, and then give it an extra 1/8 turn IN to take up slack.
                    That's the procedure for setting up the SIZING die. The seater die is the opposite.

                    Comment

                    • #11
                      Stockton
                      Vendor/Retailer
                      • Oct 2007
                      • 1316

                      J-cat is right on.
                      http://youtu.be/7Ii2kyQP-Is

                      Comment

                      • #12
                        Lucky Scott
                        Veteran Member
                        • Dec 2008
                        • 2612

                        "The seater die is the opposite."

                        So, after using the full length seater die, will I see crimps or distortion on the brass, is this normal?

                        Comment

                        • #13
                          J-cat
                          Calguns Addict
                          • May 2005
                          • 6626

                          If you are seeing dents in the shoulder after full length sizing, then you are using too much lube. The lube pools and exerts hydraulic pressure against the brass. The brass gives and you see dents in the shoulder. Use a minimum amount of lube.

                          Comment

                          • #14
                            J-cat
                            Calguns Addict
                            • May 2005
                            • 6626

                            The seater die should not be marking the brass at all. It should not be touching it. The seater should slide over the case and line up the seater stem over the case neck, that's it.

                            Comment

                            • #15
                              stilly
                              I need a LIFE!!
                              • Jul 2009
                              • 10685

                              Originally posted by Lucky Scott
                              "The seater die is the opposite."

                              So, after using the full length seater die, will I see crimps or distortion on the brass, is this normal?
                              NO!

                              Full length is a SIZER, not a SEATER.

                              A Seater pushes the bullet down and in some/most cases, crimps as well.

                              I am not familiar with 7mm so I do not know that it crimps, It sounded like it did

                              If there are TWO knobs on top, the very top/middle knob will be your bullet depth/seater stem control.

                              The lower knob will usually be your crimp adjustment, at least for pistol dies and some rifle dies as well. it is possible to have your seater up too high and crimp too hard and will buckle your brass. It is also possible to have your seater too low and your crimp turned off (or just too high) and your brass might buckle or it might just press the bullet WAY down. So you read the DIE instructions for installing it, but leave the seater knob all the way high, then with the shell in the die you slowly turn the bullet seater until you feel the resistance. then back it out and have a look, need to seat a little deeper? turn the seater down a little more and repeat until the depth is good. Then turn the crimper knob a little bit while holding the seater knob from moving and then run the shell through. Adjust as needed.

                              IF I am completely wrong, then I will delete this post since it will only confuse.

                              But there is NOTHING that I know of called a FULL LENGTH SEATER. NOTHING. The only full length ANYTHING is a sizer, and that refers to your brass forming. And once you fire brass in your bolt gun, you only need to neck size it, which will get rid of the full length sizer...
                              7 Billion people on the planet. They aint ALL gonna astronauts. Some will get hit by trains...

                              Need GOOD SS pins to clean your brass? Try the new and improved model...



                              And remember- 99.9% of the lawyers ruin it for the other .1%...

                              Comment

                              Working...
                              UA-8071174-1