Unconfigured Ad Widget

Collapse

Dillon 650 Casefeeder

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • Pauliedad
    CGN/CGSSA Contributor - Lifetime
    CGN Contributor - Lifetime
    • Dec 2012
    • 2095

    Dillon 650 Casefeeder

    Hi Guys,

    So Ive been running with a mouth breather built, ebay acquired, POS casefeeder on my 650 for a while now..... Yes, I'm holding my head down in shame.

    Anyway, after the 750,004th adjustment/tweak I went to my computer last night and ordered the Dillon casefeeder with the needed shellplates.

    Anything y'all can learn me about the new set up? Anything I need to be on the lookout for? I always read the directions but was looking for that little extra wisdom I've found so often only here.

    Thanks, Paul
  • #2
    joelogic
    Calguns Addict
    • May 2008
    • 6597

    You literally mount it and fill it with brass.

    Personally mine only likes 3/4 of a bin of brass but Dillon says it should feed two full bin scoops. I dont care to spend $60 on a motor until it totally goes out.
    Micro/Mini Reflex Red Dot Sight Mount for the M1, M1a/M14 platform

    Comment

    • #3
      tiller
      Senior Member
      • Jun 2011
      • 794

      Tighten the clutch and fill with brass
      .223 & .308 brass processing

      Comment

      • #4
        Divernhunter
        Calguns Addict
        • May 2010
        • 8753

        Just mount it and go. You may want to adjust the clutch but I did not need to on mine.
        A 30cal will reach out and touch them. A 50cal will kick their butt.
        NRA Life Member, NRA certified RSO & Basic Pistol Instructor, Hunter, shooter, reloader
        SCI, Manteca Sportsmen Club, Coalinga Rifle Club, Escalon Sportsmans Club, Waterford Sportsman Club & NAHA Member, Madison Society member

        Comment

        • #5
          joelogic
          Calguns Addict
          • May 2008
          • 6597

          I will give it a shot. Thanks.
          Micro/Mini Reflex Red Dot Sight Mount for the M1, M1a/M14 platform

          Comment

          • #6
            CGT80
            Veteran Member
            • Jul 2008
            • 2981

            Hornady case feed plates are supposed to work exactly the same as the dillon plates, but they are cheaper. I just picked up a large rifle plate from midway for 21 bucks and dillons is 45 bucks. I will find out for sure later this week.

            Oh yeah, the Dillon 1050 and Mr. Bulletfeeder run better under the casefeeder than the 650

            I run 9mm on the 1050 and all my other loads on the 550. I actually wish my 550 was a 650 instead, but I have way too many toolheads and caliber conversions to warrant selling and going to a 650. I managed to make my 550 casefeeder run rifle brass but it would be much better on the 650.

            Congrats on the upgrade it is worth it. Pay once, cry once, enjoy it for many years to come!
            He who dies with the most tools/toys wins

            Comment

            • #7
              damndave
              I need a LIFE!!
              • Oct 2008
              • 10858

              You can use the Hornady plates for SP and LP, but NOT SR.

              Comment

              • #8
                stilly
                I need a LIFE!!
                • Jul 2009
                • 10685

                Originally posted by Pauliedad
                Hi Guys,

                So Ive been running with a mouth breather built, ebay acquired, POS casefeeder on my 650 for a while now..... Yes, I'm holding my head down in shame.

                Anyway, after the 750,004th adjustment/tweak I went to my computer last night and ordered the Dillon casefeeder with the needed shellplates.

                Anything y'all can learn me about the new set up? Anything I need to be on the lookout for? I always read the directions but was looking for that little extra wisdom I've found so often only here.

                Thanks, Paul
                So in order to avoid crying twice, you now will be crying three times.

                There was a guy on either GB or Fleabay that sold these at a nicely discounted price, they were maybe around 200 or less or something like that. He had mentioned that the Dillon was better then the Hornady and that they were not interchangeable. :\ Sorry, that is all I got.
                7 Billion people on the planet. They aint ALL gonna astronauts. Some will get hit by trains...

                Need GOOD SS pins to clean your brass? Try the new and improved model...



                And remember- 99.9% of the lawyers ruin it for the other .1%...

                Comment

                • #9
                  Rwnielsen
                  Senior Member
                  • Oct 2009
                  • 639

                  Dillons says to adjust the clutch so the plate will slip before the motor stalls. Doing this will add years of life to the motor. I've been running mine that way for over 10 years and it has never slowed me down or given me any issues. Don't over fill it and you'll be fine.
                  NRA Lifer/Endowment/Patron Member

                  Comment

                  • #10
                    Pauliedad
                    CGN/CGSSA Contributor - Lifetime
                    CGN Contributor - Lifetime
                    • Dec 2012
                    • 2095

                    Good to hear all this. Yes, the cry once is always better. Glad to know the incoming casefeeder is plug and play.
                    Loaded a couple hundred .45 today and can tell you hand loading 21 cases at a time into the feed tube gets old.

                    Comment

                    • #11
                      XxWoodsHunterxX
                      Senior Member
                      • Nov 2009
                      • 1698

                      Originally posted by CGT80
                      Hornady case feed plates are supposed to work exactly the same as the dillon plates, but they are cheaper. I just picked up a large rifle plate from midway for 21 bucks and dillons is 45 bucks. I will find out for sure later this week.

                      Oh yeah, the Dillon 1050 and Mr. Bulletfeeder run better under the casefeeder than the 650

                      I run 9mm on the 1050 and all my other loads on the 550. I actually wish my 550 was a 650 instead, but I have way too many toolheads and caliber conversions to warrant selling and going to a 650. I managed to make my 550 casefeeder run rifle brass but it would be much better on the 650.

                      Congrats on the upgrade it is worth it. Pay once, cry once, enjoy it for many years to come!

                      2
                      questions
                      Did the plate work from Hornady and how did you get rifle to work in the 550 that's the only thing that has stopped me from buying for my 550. Can you send me pictures of it. By chance

                      Charles

                      Comment

                      • #12
                        CGT80
                        Veteran Member
                        • Jul 2008
                        • 2981

                        Originally posted by XxWoodsHunterxX
                        2
                        questions
                        Did the plate work from Hornady and how did you get rifle to work in the 550 that's the only thing that has stopped me from buying for my 550. Can you send me pictures of it. By chance

                        Charles
                        The large rifle plate worked pretty well. I did have an issue with the brass sometimes hanging up on the edge of the casefeeder right before it would get to the dump area on the front. I don't know if this is due to the plate or if it is just the way the machine is shaped. I may be able to smooth out that edge or put a deflector on it. I do have the 550 case feeder, and I don't know if it is any different than the 650 or 1050 versions, in this area.

                        On the 550, you will need the colored plastic adapters that the 650 uses. I just looked in the parts list for the 650 and bought those from dillon. They drop right in just like the 550 parts. The aluminum tracks are another story. The 650 version is longer. I did take a couple and grind them down, carefully, to match the 550 version. It wasn't real difficult, but it took time. A belt sander, angle grinder with a flap wheel, bench grinder, or die grinder may all work. Needle files will help get the burrs out of the track. The plastic parts and the tracks are about 16 bucks each . Sometimes the track for a particular caliber doesn't even fit much better than a track that I had for pistol brass. So, try the tracks that you do have already. 45 acp works with 243, 308, 30-06, and 30-30. 223 might work with 9mm IIRC.

                        You will of course need the right shell plate for the collator. 223 needs small rifle. 30-06, 30-30, 460 S&W mag, all used the large rifle. The last issue will be getting the brass to push into the shell plate before the ram gets high enough to allow the case mouth to hit the frame of the press or edge of the first die. The cam plate controls this. It is just a flat steel plate the a leg off the bottom that attaches to the right two mounting bolts for the press. You adjust the plate and then tighten those 7/16 head mounting bolts. I made a new plate that has a different angle. You could modify the existing plate, but I would only do that if you bought an extra. I had to switch back to the stock plate for loading pistol rounds. My cam plate moved the brass too fast and it would catch on the corner of the shell plate.

                        The casefeed system for the 550 and the 550 were not made to feed rifle brass from a casefeeder. It does not work perfect for me. It may be possible to do little tweaks here and there to help out. If 223 brass drops down the tube while the ram is down, it may knock the bottom piece over. It will usually drop while the ram is up. I sometimes have to take a half a second pause while the cases drop. If you watch what you are doing and you are good with mechanical things, it is well worth running the casefeeder. I ran the rifle brass at first by just filling the case feeder tube, then I got the right shell plates. I wouldn't want to go back to feeding brass by hand.

                        I did some last minute reloading yesterday. I had 223 in the casefeeder, so I just loaded the tube with the 30-30 brass. I only loaded 50 rounds so it was no big deal. It still seemed better to load a handful at a time than to have to push brass into the shellplate every time.

                        The right cam is stock. I drew where I thought I needed to remove metal. I am glad I didn't modify the stock part. It was tricky to get the angle right on the leg of the new cam. I welded them together. It would be easier to buy a new cam and then just grind it, but it probably isn't cheap.



                        Home made cam plate and white adapter for 223.



                        Another shot of the 550 casefeed mechanism. You can see in the bottom right corner that I made a holder for my akro bins. It holds the finish rounds in the back, and a bin closer to the reloader is positioned to where it is very easy to pick empty brass to be fed into the machine, when not using a casefeeder or when feeding the tube by hand (I made it before I added the casefeeder). I tig welded some aluminum scraps together and screwed the bracket to my homemade steel base that the press sits on.



                        A shot that shows the plastic adapter and the aluminum track that the brass slides through.

                        He who dies with the most tools/toys wins

                        Comment

                        • #13
                          elemenope
                          Senior Member
                          • Oct 2012
                          • 635

                          I like my Dillon casefeeder. No issues running rifle cases, but in my last session loading 45 ACP, I had issues with the cases not dropping and getting partially stuck in the teeth and then ultimately the feeder itself jamming it. Switching speed to slow seemed to help, but I still haven't sorted out the problem yet.

                          As for tips, make sure the casefeed tube is fully seated and the sensor bar on the feeder won't snag open and stop the motor when it's still empty.

                          Comment

                          • #14
                            CGT80
                            Veteran Member
                            • Jul 2008
                            • 2981

                            Originally posted by elemenope
                            in my last session loading 45 ACP, I had issues with the cases not dropping and getting partially stuck in the teeth and then ultimately the feeder itself jamming it. Switching speed to slow seemed to help, but I still haven't sorted out the problem yet.
                            I have that problem sometimes as well. It happens on the 550 with 40 S&W brass (only one speed), and it also sometimes happens with 9mm on the 1050. I haven't tried the slow speed on the 1050 since I probably load at a rate of 1500 rounds per hour. Maybe it would keep up. If I load at a fast pace I will hit 2k rounds per hour, but my arm gets tires after a few hundred rounds when going that quick.

                            I tried adjusting the silver metal clip where the brass drops from the collator, but I haven't found the perfect spot yet. I had this issue less often when the feeders were new, but I don't see how they may have changed. I even clean the insides with alcohol once in a while since the case lube will eventually build up.
                            He who dies with the most tools/toys wins

                            Comment

                            Working...
                            UA-8071174-1