Request for Recipe (.308), also info to share

[nickel_1022]

Remington 700 aac-sd
20" 1in10
40.5 imr 4895
Win brass...win primer
Smk hmk amax 168
2.015 coal
Getting under an inch group on a good day at 200 yrds
@65 degrees
Only about 2400 fps though...around a 5" drop between 100&200 yards. Gonna have to bump up powder to increase velocity but not sure the group will be as tight.

[GJC]

175gr SMK with 41.9gr of IMR 4064 at 2.800" OAL. .2 groups at 100yds out of a Remington 700 5R

Got some 4064 on the way, will try same load in my 5r thanks.

[Dannicus]

Anybody have a load data using IMR 4759 and 168gr jsp? I can't find any with these heavier projectiles.

[kcheung2]

^ reported for spam

[windrunner]

175 gr. SMK HPBT 11.34 grams
OAL = 2.78"
43.5 gr. of Accurate 2495
CCI BR2 primers
LC brass trimmed to 2.00"

Windrunner M12 with a 26" Pac-Nor med. heavy barrel

The load and the rifle give me .25" MOA out to 1k.

[ar15barrels]

The load and the rifle give me .25" MOA out to 1k.

Please post at least three 0.25 MOA 1000yd groups that you fired on the same day.

[Ahhnother8]

The load and the rifle give me .25" MOA out to 1k.

Please post at least ONE 0.25 MOA 1000yd group that you fired EVER. Or even one from 100 yards.

[phdo]

175 gr. SMK HPBT 11.34 grams
OAL = 2.78"
43.5 gr. of Accurate 2495
CCI BR2 primers
LC brass trimmed to 2.00"

Windrunner M12 with a 26" Pac-Nor med. heavy barrel

The load and the rifle give me .25" MOA out to 1k.

Please post at least three 0.25 MOA 1000yd groups that you fired on the same day.

Please post at least ONE 0.25 MOA 1000yd group that you fired EVER. Or even one from 100 yards.

I, too, would like to see this group. Just ONE will satisfy my curiosity.

[Rickmcu]

Windrunner M12 with a 26" Pac-Nor med. heavy barrel

The load and the rifle give me .25" MOA out to 1k.

I literally lol'd!! That is hilarious!

[ILVSMOG]

LOL, the internet always brightens my day.

[phdo]

Does anyone have a good load for a GAP-10 in .308? I will be receiving my rifle soon and would like to work up some loads before it gets here. Thanks.

[45R]

Remington 700P 1:12 Twist 26" barrel
COAL 2.915
42 Grain IMR 4064
Federal Brass
Fed 210M Primer
168 SMK
2650 FPS at 50 degress

[ruben385]

Has anyone shot an FN .308 patrol bolt action trying to find out a good accurate ammo for it

[CK_32]

Factory remingtons almost universally will shoot the best between 43.5 and 44gr with that bullet at that seating length.
Thicker brass will drop the node by 1/2gr.
That means that Lapua or Lake City brass will be lower charges than most other commercial brass.

Yup

My 700 SPS T has a node at 43.6 - 44.3 and again at 45.5 - 46.0

WIN brass
Varget
175 SMK
1:12
CCI 200
2.800 OAL

Still trying to test for my 168's and both 168/175 for my LR308

[OC_Mike]

Guys, I have a question regarding my AR10 DMR setup... (if I missed a previous posting with the same question please excuse me)

Does anyone have a similar setup like mine below and which bullet works best for you at 450 to 600 yards?

AR10 semi-auto, 18" 1:10 twist, rifle length gas, Ares Armor barrel (not match)

Newbie reloader here with the following bullets, brass, powder, primer....

Powder: IMR 4046 / Primer: CCI 200's

Bullets I will be testing and requesting your opinion for near optimum (not maximum) powder load.....

168 grn Horny Amax BT
178 grn Horny Amax BT
180 grn Horny Interlock SPBT

200 and/or 220 Sierra MK or Lapua BT (I dont have these but thinking about buying some to test)

....do I need to up the powder to 4839 (is it? forgot the #) on heavier bullets?

Thanks for your input guys!