I don't bump the shoulder back at all. It is only necessary to decrease the diameter of the brass near the casehead, hence the need to use a full-length die every so often when using a neck die. This is why, "When you set up your sizing die you should adjust it out longer than the die maker recommends." This applies to bolt guns and even AR's with Wylde chambers or very tight CLE chambers.
Unconfigured Ad Widget
Collapse
|
|
|
|
|
|
|
|
Setting your FL sizing dies correctly
Collapse
X
-
-
Measuring reveals things ....
When you don't bump the shoulder back at all, your handloads will soon become too tight. Why would you want your handloads to be different sizes? Some fit loose, some fit fine, some are too tight, while others might not even chamber.
It just takes a few extra seconds to measure your handloads, and set your die height perfectly to make uniform handloads. Another benefit to measuring is to verify that competition shellholders are really working the way you think. I also use the Redding comp shellholders, and I was surprised to see the effect of using them when you can actually measure your handloads.
You would probably get ticked off if your house was built without measuring. Why would anyone not want to not measure their handloads?Visit our website at WWW.LARRYWILLIS.COM (It's devoted to helping shooters make the best handloads possible.)Comment
-
What some people have done is taken their body dies and used three fired cases from their chamber to power lap the die to fit their fired case exactly. That way only the shoulder is bumped and the rest of the case is only sized .001" or so. That way all the rounds chamber easy, yet case life is the same as neck-sizing.Comment
-
Tagged for great infoNever return fire!
2e 32 32 20 2e 33 38 30 20 2e 33 38 20 39 6d 6d 20 2e 34 34 20 2e 35 30 41 45 20 2e 32 32 33 20 35 2e 35 36 20 33 30 2d 33 30 20 2e 33 30 38 20 2e 35 30 44 54 43 20 32 32 2d 32 35 30 20 33 37 4d 4d 20 2e 34 35 41 43 50Comment
-
When you don't bump the shoulder back at all, your handloads will soon become too tight. Why would you want your handloads to be different sizes? Some fit loose, some fit fine, some are too tight, while others might not even chamber.
It just takes a few extra seconds to measure your handloads, and set your die height perfectly to make uniform handloads. Another benefit to measuring is to verify that competition shellholders are really working the way you think. I also use the Redding comp shellholders, and I was surprised to see the effect of using them when you can actually measure your handloads.
You would probably get ticked off if your house was built without measuring. Why would anyone not want to not measure their handloads?
When I started hand loading almost 40 years ago, there were no commercial measuring gauges available to hand loaders.
We used to get our resizing measurements by trial and error, it worked, but was a little time consuming.
A few years ago, I bought the Stoney Point (now Hornady) headspace gauge set. I used a digital set of calipers. When I started measuring, I was amazed at the numbers. I have a Winchester Mod. 70 30/06 that was giving me difficult chambering on my hand loads. When I measured the shoulders using the gauge, I found I was not bumping the shoulder back enough. I found the minimum measurement for chambering using the last two digits (since they are the most important numbers) in the measurement was .43". Anything over .43" didn't chamber smoothly. I was able to set my dies to resize .40"-41" and all of the ammo chambered smoothly.
Over the years, I've had a couple of rifles finicky over resizing. The great thing with these gauges is the numbers are looking right in the face and it is so quick to set your dies for a rifle to bump the shoulder .002"-.003" or more for a gas gun if needed.
No matter what gauge you decide to use, Hornady, Sinclair, RCBS or Innovative Technologies, they will give you the numbers. I prefer a gauge that will read in digital numbers, it's just easier to see.
For around 40 bucks, you can quit guessing or using the old method of resizing in little increments at a time, then testing the case in your rifle's chamber(which does work). Well worth the cost.Comment
-
i just set mine to touch the shellholder i cant imagine setting it any other way cause that would mean its not doing its job
i reload for many guns so i make my ammo to work in all
but i am purely an economic reloader not a bench rest fanatic
but the old saying is true beware the man who just has one gun because he probably knows how to use itComment
-
Can anyone explain the purpose of setting the FL die until the press "cam's over"? Some people say to just screw down until the shell holder touches the die and that's it, other people say go 1/4 turn past when the shellholder touches the die. I've seen it said both ways no matter if the dies are carbide or not, single stage or progressive. I guess I'm just not sure of the true purpose of "cam over".
Thanks.Comment
-
amoril ......
Not all presses allow you to "cam-over". The new Rockchucker Supreme is a good example. The whole idea of the cam-over feature is to feel your shellholder bump into the die by allowing the ram to lower at the top of its stroke.
Cam-over ensures that you have not short stroked your press and failed to resize all the way. However, as we've been discussing, it's far better to "measure" the clearance "at the shoulder" that YOUR handloads have in YOUR particular chamber.
Just about every time I go to the range somebody has handloads that won't chamber, or they're getting headspace separation. It's very easy to make much better quality handloads if you measure properly, and don't assume all is well. It's usually not. The Digital Headspace Gauge isn't just for benchrest shooters. It helps avoid these common problems.Visit our website at WWW.LARRYWILLIS.COM (It's devoted to helping shooters make the best handloads possible.)Comment
-
I also, am not a bench rest fanatic. You may be able to get pistol and other straight walled cartridges to chamber by just touching the shell holder with your die, but like I said in my other posts, I had a Winchester Mod 70 30/06, a Mauser 270 Win. and a .223 Rem in a Factory Colt AR-15 that would not chamber brass resized by just touching the shell holder. For these rifles, I had to adjust the die down more and cam over TDC to get them to reliably chamber.i just set mine to touch the shellholder i cant imagine setting it any other way cause that would mean its not doing its job
i reload for many guns so i make my ammo to work in all
but i am purely an economic reloader not a bench rest fanatic
but the old saying is true beware the man who just has one gun because he probably knows how to use it
I reload for at least 9 bottle neck rifle calibers and the headspace gauges I am discussing here make the job of properly resizing fired brass from your Rifle's chamber very easy. The brass properly resized lasts much longer than brass that you just guess how much you're sizing.Comment
-
I also, am not a bench rest fanatic. You may be able to get pistol and other straight walled cartridges to chamber by just touching the shell holder with your die, but like I said in my other posts, I had a Winchester Mod 70 30/06, a Mauser 270 Win. and a .223 Rem in a Factory Colt AR-15 that would not chamber brass resized by just touching the shell holder. For these rifles, I had to adjust the die down more and cam over TDC to get them to reliably chamber.
I reload for at least 9 bottle neck rifle calibers and the headspace gauges I am discussing here make the job of properly resizing fired brass from your Rifle's chamber very easy. The brass properly resized lasts much longer than brass that you just guess how much you're sizing.
hmm i guess i dont ajust it till it touched what i do is tighten it down till i can't do the cam over and back it off till i just can "cam over" then once its camed over and die locked i adjust the die nut and lock it in place
i only reload 30 carbine,9mm,45acp,223,308 so i'm not as experienced as most but my stuff goes off and i keep my loads mildComment
-
for my 300 mag i use full length dies but when i bought them the guy told me not to set it touching the shell holder instead place a nickel on top and tighten die to til it hits the nickel.
Been doing it this way for year with no probs.For my .223s i barely make contact with the shell holder then loosn slightly i do it this way cause i shoot in 2 different guns and this has worked fine for use in both gunsComment
-
Here's an article with photos to show how to use the Hornady head space gauge set. All you need is a set of digital calipers and the gauge set. Once you see the numbers, you can fine tune your resizing die to minimally resize for your rifle, which will give you longer case life. It really isn't difficult.
Years ago,I had a Winchester Mod. 70 in .338 Win Mag. I would get three firings and would get case head separations. I didn't know at the time, but now I understand I was likely over sizing those cases.
I see many who use the internet for their reloading information, but a good library of reference and reloading books helps a lot. I do like the internet for finding articles and being able to converse with others.
If you want a good reference other than just a reloading manual, "Reloading for competition" by Glenn Zediker is a great resource. He writes in layman terms. Even though I don't use some of the techniques he explains, he makes it easier to understand all this stuff.Comment
-
Recent Improvements in Handloading ...
Deadon .....
I have a new video available from my website. It includes 20 minutes "at the reloading bench" using the Digital Headspace Gauge and the Belted Magnum Collet Resizing Die. It simplifies the headspace issue for handloaders.Visit our website at WWW.LARRYWILLIS.COM (It's devoted to helping shooters make the best handloads possible.)Comment
Calguns.net Statistics
Collapse
Topics: 1,870,936
Posts: 25,177,612
Members: 358,862
Active Members: 5,392
Welcome to our newest member, 1776 Arms.
What's Going On
Collapse
There are currently 37653 users online. 39 members and 37614 guests.
Most users ever online was 239,041 at 11:39 PM on 02-14-2026.

Comment