Unconfigured Ad Widget

Collapse

Setting your FL sizing dies correctly

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • Fjold
    I need a LIFE!!
    • Oct 2005
    • 23094

    Setting your FL sizing dies correctly

    It is very important to makes sure that you adjust your sizing die to fit your individual rifle's chamber. If you set the sizing die to the die maker's instructions it will FL size your cases to the minimum SAAMI dimensions and your cases will stretch every time that you fire them. Besides the negative effects on accuracy, your cases will fail earlier due to case stretching or work hardening earlier.

    When you set up your sizing die you should adjust it out longer than the die maker recommends. Leave it up .250" over the shell holder. Lube and size a fired case from your gun and see if that case chambers easily in your gun. (It should not). Keep adjusting the die down in quarter turn increments using fired cases until the bolt handle just closes on the sized case with you barely feeling it (compare it with operating the bolt with no case).

    This will insure that the sized cases perfectly fit your chamber, which should give the best accuracy, the longest case life and it should cut way down on trimming cases for length.

    As an example:
    I have 22.250 cases that are notorious for stretching (long sloping shoulder). I load them right to book max for most loads and above some book recommendations for other loads. I bought new cases and trimmed them all to 1.9" (the maximum length is 1.912"), after their 7th reload my cases are all around 1.94" long. Because I'm not overworking the brass, I should easily get 15 reloads out of these cases and I may never have to trim them for length.
    Frank

    One rifle, one planet, Holland's 375




    Life Member NRA, CRPA and SAF
  • #2
    chickenfried
    Calguns Addict
    • Oct 2005
    • 7160

    thanks for the tip!
    Originally posted by victor1echo
    Hollywood is satan!!!!
    sigpic

    Comment

    • #3
      amoril
      Junior Member
      • Oct 2010
      • 53

      Do you need to FL resize each time? I've yet to start reloading so I might be wrong on this but I thought that if the case had never been fired in your gun you should do a FL resize on that case when you reload it, after that you should be fine just neck sizing. Is that not correct?

      Comment

      • #4
        FLIGHT762
        Veteran Member
        • Mar 2009
        • 3072

        Setting your die to resize the proper headspace is very important as Fjold explained.

        I reload for nine rifle calibers. I finally spent the $40.00 for the Hornady headspace gauge set. One of the best tool investments I've made. http://www.midwayusa.com/viewproduct...tnumber=479704

        With the gauge, I can quickly take measurements using a digital caliper from my fired cases and set my dies to only bump the case shoulder back .002"- .003". With the digital calipers, I can see the numbers and rather quickly, I can set my dies to resize minimally, extending case life greatly.

        Some dies can set shoulders back quite a bit, some don't. With the headspace gauge set, you can see the numbers.

        I had a friend give me some used .300 Win .Mag. bras that had been resized. When I used the gauge, I found the brass had the shoulder set back .025"! Good to find out.

        I like the Hornady set because they will work for nearly every caliber.

        Comment

        • #5
          FLIGHT762
          Veteran Member
          • Mar 2009
          • 3072

          Originally posted by amoril
          Do you need to FL resize each time? I've yet to start reloading so I might be wrong on this but I thought that if the case had never been fired in your gun you should do a FL resize on that case when you reload it, after that you should be fine just neck sizing. Is that not correct?
          For my hunting rifles and gas guns, I full length resize every time. I only neck size in my target rifles. When picking up range brass,yes, they all get F/L resized. My F/L dies are set to resize minimally in the rifle it was fired in.

          I'm very careful in neck only sizing. I will only neck size about three times before F/L resizing again. I've had some close calls getting a loaded neck sized case stuck in my chamber. At some point even after being fired in the same rifle, you will need to F/L size.

          Comment

          • #6
            amoril
            Junior Member
            • Oct 2010
            • 53

            Great, thanks for the tips. I'm going to have to read more about the headspace gauges since I'm not quite clear on how to use them, but thanks for pointing me in the right direction.

            Comment

            • #7
              amoril
              Junior Member
              • Oct 2010
              • 53

              In case anyone else wants it here's an article explaining the usage of the gauges that Flight762 mentions:

              Comment

              • #8
                brando
                Veteran Member
                • Feb 2006
                • 3694

                Just be careful when matching cases to chamber length. It's easy to get things too tight and cause either a stuck case or excessive pressure. The Sinclair shoulder gauges are handy in measuring shoulder bump.

                Dang, missing my rifles and reloading gear
                --Brando

                Comment

                • #9
                  Spanky8601
                  Senior Member
                  • Apr 2010
                  • 2297

                  Originally posted by amoril
                  In case anyone else wants it here's an article explaining the usage of the gauges that Flight762 mentions:
                  http://www.inlandshooters.net/index.php?contentid=99
                  Thanks for the link. Cleared up some questions that I had.
                  May I always be the type of person my dog thinks I am

                  Comment

                  • #10
                    Mrskylinetou
                    Senior Member
                    • Aug 2010
                    • 528

                    When I FL size I just dial the die all the way down so it touches the shell plate. I have redding dies and never had a problem. I'm sure I'm not doing this right. I don't have a head space guage

                    Comment

                    • #11
                      Mrskylinetou
                      Senior Member
                      • Aug 2010
                      • 528

                      I got 25k brass at my disposal so longevity doesn't matter. Some are for accuracy some are for plinking and 3gun. I have redding 3 dies set and that was how I was told to set my dies. Now I load for 40 sw and I just dialed the die all the way down.

                      Comment

                      • #12
                        bcrich
                        Senior Member
                        • May 2008
                        • 1160

                        Good looking out Frank!

                        Comment

                        • #13
                          Innovative
                          Junior Member
                          • Oct 2009
                          • 49

                          Chamber clearance ...

                          Conventional headspace gauges are designed to help install rifle barrels, and that's about it. They are of very little use to the handloader.

                          However, there's a quick and easy way to set the height of your sizing dies. I recommend using the Digital Headspace Gauge. It can setup your die height (in seconds) to produce handloads with -.001" to -.002" chamber clearance "at the shoulder".

                          The Digital Headspace Gauge requires no special bushings or attachments, and it works on ALL different calibers. It can also measure the bullet jump to the rifling in your particular chamber.
                          Visit our website at WWW.LARRYWILLIS.COM (It's devoted to helping shooters make the best handloads possible.)

                          Comment

                          • #14
                            J-cat
                            Calguns Addict
                            • May 2005
                            • 6626

                            I recommend using Redding's competition shellholder set. They are designed to adjust headspace in .002" increments. You simply screw the die down to cam over, start with the .010" over shellholder and work your way down.

                            Comment

                            • #15
                              FLIGHT762
                              Veteran Member
                              • Mar 2009
                              • 3072

                              For adjusting sizing die headspace I use these:

                              They cost $10.00.

                              The Redding set is nice, but costs $45.00.


                              Just another option.

                              Comment

                              Working...
                              UA-8071174-1