My reloading gear is set up against a concrete wall in the basement. There is a small gap between the top of the table and the wall. This leads to some movement while seating primers. Any ideas?
Unconfigured Ad Widget
Collapse
|
|
|
|
|
|
|
|
Making bench more stable
Collapse
X
-
Making bench more stable
sigpicOriginally posted by victor1echoHollywood is satan!!!!Tags: None -
Sounds like you simply need to drill some holes into the concrete wall and put some wood up to lag to. That ought to work really well and stop the shakes.
A hammer-drill works best, they can be rented if need be. You should be able to buy a few concrete wedge anchors for not too much money, nothing really large, 1/4" - 3/8" should be sufficient. The anchor should indicate what depth you should drill along with the drill bit size.
Lag a few 2 x 4's to the wall with the wedge anchors and lag your bench to them with lag bolts or heavy wood screws. That should work.
If it's out of level, you may need to shim the leg/s to level it first, that would probably help right out of the gate and you may not even need to lag to the wall.Comment
-
level the table to the wall by shimming the legs on the floor, then put 1/2 inch redheads into the wall through the back of the bench to make it not move....Comment
-
Weigh the bench down? Buy a heavier bench? Reinforce the bench? Stop using so much force? You are welcome to use my hammerdrill.Comment
-
I wish I was lucky enough to have a basement.
I don't know how sturdy or well made your bench is but I would suggest anchoring it to as many walls as possible by moving it to a corner if possible. Anchoring the legs to the floor may be a good idea to help level it and keep it from moving.Some people will do skanky things for $25, and not all those people are crack whores.
Bill Wiese
San Jose, CA
sigpicComment
-
Forgot to add I didn't want to put any holes in the concrete. I ended up sticking some wedges I had laying around into the gap. Seemed to take care of it. Thanks for the suggestions and offers.sigpicOriginally posted by victor1echoHollywood is satan!!!!Comment
-
If you can't/won't put holes in the wall, then put some weight on the bench and make the tabletop as stiff and heavy as you can. I've got a bench with the tabletop made of 4-3/4" sheets of plywood bonded together and the entire bench weighted down with about 1000# of lead. It doesn't move.Luck favors the prepared.
The original battle plan did not survive initial contact with the enemy.
"The things that will destroy America are prosperity at any price, peace at any price, safety first instead of duty first, the love of soft living and the get rich quick theory of life." -Theodore RooseveltComment
-
Some times scrap granite countertop material can be had for the asking.
If the bench isn't stiff enough, brace it. Triangles are strong.Comment
-
I much prefer my hand primer seaters if that is your only problem. they are easier to handle primers with. My Ponsness and Warren 900 takes some force with the long lever, I have a rather large bench and a few hundred lbs of shot in the bottom. Has not been a problem.Comment
-
Hand priming? Right after I start driving a model T ford.
Just kidding, appreciate the input. But I'm using a progressive press.
The wedges seemed to work. But I just finished a reloading session when I posted the question. So I'll see how well it works next time.sigpicOriginally posted by victor1echoHollywood is satan!!!!Comment
Calguns.net Statistics
Collapse
Topics: 1,870,844
Posts: 25,176,567
Members: 358,862
Active Members: 5,398
Welcome to our newest member, 1776 Arms.
What's Going On
Collapse
There are currently 27843 users online. 57 members and 27786 guests.
Most users ever online was 239,041 at 11:39 PM on 02-14-2026.


Comment