Unconfigured Ad Widget

Collapse

Help Please. Case Head Separation.

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • #31
    CptDan
    Senior Member
    • Jan 2011
    • 519

    I had this happen on the first reload on my Ruger American Predator. My headspace was off .009. Bought the gauges and reset the barrel hasn't happened since.

    Comment

    • #32
      bigdawg86
      Veteran Member
      • Mar 2012
      • 3554

      Originally posted by ar15barrels
      No depth rod?

      Really?



      Oops your right. Never used the depth rod so it kinda forgot about it.

      Sent from my SM-G950U using Tapatalk

      Comment

      • #33
        bigdawg86
        Veteran Member
        • Mar 2012
        • 3554

        So depth was 0.014" below the low mark of the case gauge. Yeah I screwed the pooch on these ones. Like I said I must have accidentally set up with Whidden die against shell holder like you would a RCBS die.

        Sent from my SM-G950U using Tapatalk

        Comment

        • #34
          FLIGHT762
          Veteran Member
          • Mar 2009
          • 3072

          Glad to see you figured it out. Makes perfect sense now. I did that many years ago to a bunch of 222 Rem. cases. Had to toss them. Learned my lesson way back then.

          Some say you can load them really long and jam into the lands to push the case back into the bolt face without causing the stretch at the case web and it will expand the case shoulder forward. I just never have done it.

          Comment

          • #35
            JagerDog
            I need a LIFE!!
            • May 2011
            • 15873

            Palestine is a fake country

            No Mas Hamas



            #Blackolivesmatter

            Comment

            • #36
              bigdawg86
              Veteran Member
              • Mar 2012
              • 3554

              Teres Hanges

              Sent from my SM-G950U using Tapatalk

              Comment

              • #37
                bigdawg86
                Veteran Member
                • Mar 2012
                • 3554

                The final numbers are out and my mistake was YUGE. Using a shoulder bump gauge (yeah, sadly I have one but didn't use it) I was able to compare the problematic cases against once fired brass from my gun.

                I am under a whopping 0.0255" from a once fired case. So yeah, safe to say I found the problem. I doubt I can save the brass though so time to pull #100 and start over. That was about a 60 dollar mistake in terms of wasted brass.

                On the bright side I will now set up ALL my resizing dies like I know I should have using a once fired case, shoulder gauge, and then lowering die until I get 3-5 thou of shoulder bump (this gun is an autoloader).

                Comment

                • #38
                  JagerDog
                  I need a LIFE!!
                  • May 2011
                  • 15873

                  Originally posted by bigdawg86
                  Teres Hanges

                  Sent from my SM-G950U using Tapatalk
                  Hodor!


                  Onion rings.
                  Palestine is a fake country

                  No Mas Hamas



                  #Blackolivesmatter

                  Comment

                  • #39
                    ar15barrels
                    I need a LIFE!!
                    • Jan 2006
                    • 57199

                    Originally posted by bigdawg86
                    Oops your right.
                    Never used the depth rod so it kinda forgot about it.
                    Originally posted by bigdawg86
                    The final numbers are out and my mistake was YUGE. Using a shoulder bump gauge (yeah, sadly I have one but didn't use it) I was able to compare the problematic cases against once fired brass from my gun.

                    I am under a whopping 0.0255" from a once fired case. So yeah, safe to say I found the problem. I doubt I can save the brass though so time to pull #100 and start over. That was about a 60 dollar mistake in terms of wasted brass.

                    On the bright side I will now set up ALL my resizing dies like I know I should have using a once fired case, shoulder gauge, and then lowering die until I get 3-5 thou of shoulder bump (this gun is an autoloader).
                    Never stop learning.
                    Randall Rausch

                    AR work: www.ar15barrels.com
                    Handguns: www.handgunbarrels.com
                    Bolt actions: www.700barrels.com
                    Foreign Semi Autos: www.akbarrels.com
                    Most work done while you wait on a scheduled shop visit.

                    Comment

                    • #40
                      tawadc95
                      Senior Member
                      • Apr 2017
                      • 565

                      Lost that bet, I was guessing .022.

                      Comment

                      Working...
                      UA-8071174-1