Unconfigured Ad Widget

Collapse

Issues sizing 308 LC brass

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • #31
    divingin
    Veteran Member
    • Jul 2015
    • 2522

    Originally posted by devster55
    No, I adjust the die with just the shell holder on the ram.
    You should make sure that you are compensating for any press stretch that may be happening.

    Take an unsized piece of brass, lube it normally, and run it up into the sizing die. Place a flashlight on the opposite side of the ram, and look for any gap between the die and the shellholder. If there is any, lower the ram, screw the die in a bit more, and repeat with another unsized piece of brass. You want to eliminate that gap when the press is stretched to the fullest.

    Note that this may not end up being your ultimate die adjustment (which should be determined by the amount you need the shoulder moved), but rather to make sure that the case web gets sized as much as you need it to be.

    Comment

    • #32
      devster55
      Senior Member
      • Nov 2012
      • 2095

      So I have set aside the ones that didn’t pass for a later day. Now the thing that makes me scratch my head is after seating a bullet there were a few cases that originally passed now fail with a bullet seated in them. I’m using no crimp. Just one out of every few do it. But the my chamber fine in the rifle. I’m just gonna shoot it but thought it was weird.
      Good friends will come bail you out of jail. A best friend will be sitting next to you in the cell saying damn that was fun!

      Comment

      • #33
        baih777
        CGN/CGSSA Contributor
        CGN Contributor
        • Jul 2011
        • 5680

        That brass needs to be annealed before you resize it again.
        Been gone too long. It's been 15 to 20 years since i had to shelf my guns. Those early years sucked.
        I really miss the good old Pomona Gun Shows.
        I'm Back.

        Comment

        • #34
          fguffey
          Senior Member
          • Mar 2010
          • 1408

          Many years ago Lyman said crimping can be a bad habit, Dillon was that not far behind; Dillion claimed crimping should not be done while seating the bullet. In their opinion the bullet is moving down while being seated.

          Harm? The neck of the case grips the bullet while moving down, while the neck grips the bullet the neck bulges below the crimp.

          Meaning Lyman said crimping can reduce bullet hold because the bottom of the case neck not contacting the bullet. The neck being pushed down while seating and crimping causes the shoulder/neck juncture to bulge. So if the case will allow the bolt to close after sizing but will not allow the bolt to close after seating the bullet there is a big chance the reloader does not understand crimping only requires a hint of effort.

          And the reloader should consider crimping is a bad habit. Alll of my life I have measured bullet seating in pounds of effort because I am the fan of bullet hold. And then there came tension with no way to measure it, again I know about interference fit and crush fit. None of my gages measure tension.

          But there is an outside chance you are working with tensions, if so have someone that can measure tensions explain how many tensions it takes to equel 40 pounds.

          F. Guffey

          Comment

          • #35
            smoothy8500
            Veteran Member
            • Sep 2009
            • 3846


            Somebody needs to call Batman...

            Comment

            • #36
              FLIGHT762
              Veteran Member
              • Mar 2009
              • 3072

              Originally posted by smoothy8500
              Looking at the first pic, do you have any nicks or bent rims? they will hang up on the case gauge. As for chambering, if they slide in and out that is good.
              ^^^^^^^^^^^^^^This^^^^^^^^^^^^^^^^
              Brass fired in autoloaders (Machine Guns) will often have bent rims that may have been resized properly, but will hang up on the case gauge because of the bent rim, giving a false reading. Happens all the time.

              The drop in case gauges don't work well with M/G brass because of that.

              Comment

              • #37
                fguffey
                Senior Member
                • Mar 2010
                • 1408

                I have 308 sizing dies, 308 Small base dies. I have Wilson case gages, I have neck sizing (only) dies and I have home made dies. And I also have shell holders, I have shell holders that require the use of a small gasket cutting ball peen hammer to it fit a screwed up case to fit the shell holder. Common sense should tell the reloader why the shell holder does not fit; backup, all of my shell holders are not alike. Most of my shell holders fit like a hand me down shirt, they fit anywhere they touch.

                And then there is the other shell holders. With the other shell holders it should not take a reloader very long to determine there is something wrong because the case fit the shell holder before firing.

                Back to the case fitting, the case head will fit into the bottom of the die, if the case head will not fit into the bottom of the die the case head has been hammered with a heavy load. One more time; the Wilson case gage measures fired cases and cases that are minimum length/full length sized. AGAIN, if the case head does not fit into the Wilson case gage head first the case head is screwed up.

                And now we come to the seating of bullets. When bullets are seated caution must be exercised then seating the bullet with a crimp. The crimp can upset the shoulder/case body juncture area of the case. the upset will cause difficulty in chambering the round/closing the bolt etc.

                Again; Lyman suggested seating and crimping at the same time can be a bad habit.

                F. Guffey
                Last edited by fguffey; 02-06-2019, 10:15 AM.

                Comment

                • #38
                  devster55
                  Senior Member
                  • Nov 2012
                  • 2095

                  Originally posted by fguffey
                  I have 308 sizing dies, 308 Small base dies. I have Wilson case gages, I have neck sizing (only) dies and I have home made dies. And I also have shell holders, I have shell holders that require the use of a small gasket cutting ball peen hammer to it fit a screwed up case to fit the shell holder. Common sense should tell the reloader why the shell holder does not fit; backup, all of my shell holders are not alike. Most of my shell holders fit like a hand me down shirt, they fit anywhere they touch.

                  And then there is the other shell holders. With the other shell holders it should not take a reloader very long to determine there is something wrong because the case fit the shell holder before firing.

                  Back to the case fitting, the case head will fit into the bottom of the die, if the case head will not fit into the bottom of the die the case head has been hammered with a heavy load. One more time; the Wilson case gage measures fired cases and cases that are minimum length/full length sized. AGAIN, if the case head does not fit into the Wilson case gage head first the case head is screwed up.

                  And now we come to the seating of bullets. When bullets are seated caution must be exercised then seating the bullet with a crimp. The crimp can upset the shoulder/case body juncture area of the case. the upset will cause difficulty in chambering the round/closing the bolt etc.

                  Again; Lyman suggested seating and crimping at the same time can be a bad habit.

                  F. Guffey
                  Good friends will come bail you out of jail. A best friend will be sitting next to you in the cell saying damn that was fun!

                  Comment

                  • #39
                    devster55
                    Senior Member
                    • Nov 2012
                    • 2095

                    Originally posted by FLIGHT762
                    ^^^^^^^^^^^^^^This^^^^^^^^^^^^^^^^
                    Brass fired in autoloaders (Machine Guns) will often have bent rims that may have been resized properly, but will hang up on the case gauge because of the bent rim, giving a false reading. Happens all the time.

                    The drop in case gauges don't work well with M/G brass because of that.
                    The thing is, I can turn the shell over and insert them into the case gauge. They go down below the rim.
                    Good friends will come bail you out of jail. A best friend will be sitting next to you in the cell saying damn that was fun!

                    Comment

                    • #40
                      baih777
                      CGN/CGSSA Contributor
                      CGN Contributor
                      • Jul 2011
                      • 5680

                      Originally posted by devster55
                      The thing is, I can turn the shell over and insert them into the case gauge. They go down below the rim.
                      That means the brass is bent.
                      Try rolling it on a flat service.

                      They will still reload.
                      Been gone too long. It's been 15 to 20 years since i had to shelf my guns. Those early years sucked.
                      I really miss the good old Pomona Gun Shows.
                      I'm Back.

                      Comment

                      • #41
                        devster55
                        Senior Member
                        • Nov 2012
                        • 2095

                        Originally posted by baih777
                        That means the brass is bent.
                        Try rolling it on a flat service.

                        They will still reload.
                        Good friends will come bail you out of jail. A best friend will be sitting next to you in the cell saying damn that was fun!

                        Comment

                        • #42
                          baih777
                          CGN/CGSSA Contributor
                          CGN Contributor
                          • Jul 2011
                          • 5680

                          Annealing won't help. Only if it's the neck area. Sorry.

                          Roll it on a flat service. Then you will see.
                          If it's the bottom portion of the case, they will still reload. I shoot them.
                          my reloads will still shoot 1 moa. Never checked them again.

                          You can sort out the bad ones and try reloading 10 . See how they shoot.
                          Been gone too long. It's been 15 to 20 years since i had to shelf my guns. Those early years sucked.
                          I really miss the good old Pomona Gun Shows.
                          I'm Back.

                          Comment

                          • #43
                            baih777
                            CGN/CGSSA Contributor
                            CGN Contributor
                            • Jul 2011
                            • 5680

                            I am assuming the military brass is shot fully automatic mode.
                            So I think it's possible the headstamp area of the case can get tweaked.
                            Been gone too long. It's been 15 to 20 years since i had to shelf my guns. Those early years sucked.
                            I really miss the good old Pomona Gun Shows.
                            I'm Back.

                            Comment

                            • #44
                              devster55
                              Senior Member
                              • Nov 2012
                              • 2095

                              I think I’m just going to avoid this situation next time and buy new brass. Any recommendations? Thinking of starline
                              Good friends will come bail you out of jail. A best friend will be sitting next to you in the cell saying damn that was fun!

                              Comment

                              • #45
                                devster55
                                Senior Member
                                • Nov 2012
                                • 2095

                                Originally posted by baih777
                                Annealing won't help. Only if it's the neck area. Sorry.

                                Roll it on a flat service. Then you will see.
                                If it's the bottom portion of the case, they will still reload. I shoot them.
                                my reloads will still shoot 1 moa. Never checked them again.

                                You can sort out the bad ones and try reloading 10 . See how they shoot.
                                Good friends will come bail you out of jail. A best friend will be sitting next to you in the cell saying damn that was fun!

                                Comment

                                Working...
                                UA-8071174-1