Unconfigured Ad Widget

Collapse

Issues sizing 308 LC brass

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • #16
    devster55
    Senior Member
    • Nov 2012
    • 2095

    Originally posted by highpower790
    I use the RCBS case mic,I think its the better option.
    Good friends will come bail you out of jail. A best friend will be sitting next to you in the cell saying damn that was fun!

    Comment

    • #17
      highpower790
      Veteran Member
      • Jun 2013
      • 3481

      Before I would say yea or nea,is the die being adjusted with a piece of brass in it?
      I use the exact same set-up,press,die,brass for the same platform and have never had your experience.
      Keep it simple!

      Comment

      • #18
        devster55
        Senior Member
        • Nov 2012
        • 2095

        Originally posted by highpower790
        Before I would say yea or nea,is the die being adjusted with a piece of brass in it?
        I use the exact same set-up,press,die,brass for the same platform and have never had your experience.
        No, I adjust the die with just the shell holder on the ram.
        Good friends will come bail you out of jail. A best friend will be sitting next to you in the cell saying damn that was fun!

        Comment

        • #19
          baih777
          CGN/CGSSA Contributor
          CGN Contributor
          • Jul 2011
          • 5680

          that Hornady case guage measures length also. if the case is longer than spec, it bottoms out .
          if you have access to a lathe, you can drill out the guage to remove that stop.
          Hornady guage also fits tighter than others.


          Dillon guage works better.
          LE Wilson gauges have a looser fit

          check them in your rifle.
          Been gone too long. It's been 15 to 20 years since i had to shelf my guns. Those early years sucked.
          I really miss the good old Pomona Gun Shows.
          I'm Back.

          Comment

          • #20
            highpower790
            Veteran Member
            • Jun 2013
            • 3481

            Originally posted by devster55
            No, I adjust the die with just the shell holder on the ram.
            OK,good man.Try this ,using the chamber is the next best option.
            Back the die out to the 1st postion started with at 1/4 after making contact with the shell holder.
            Size a piece of brass ,then drop into chamber.Carefully feel for the case shoulder to make contact against chamber shoulder.
            Keep it simple!

            Comment

            • #21
              devster55
              Senior Member
              • Nov 2012
              • 2095

              Originally posted by baih777
              that Hornady case guage measures length also. if the case is longer than spec, it bottoms out .
              if you have access to a lathe, you can drill out the guage to remove that stop.
              Hornady guage also fits tighter than others.


              Dillon guage works better.
              LE Wilson gauges have a looser fit

              check them in your rifle.
              Good friends will come bail you out of jail. A best friend will be sitting next to you in the cell saying damn that was fun!

              Comment

              • #22
                devster55
                Senior Member
                • Nov 2012
                • 2095

                Originally posted by highpower790
                OK,good man.Try this ,using the chamber is the next best option.
                Back the die out to the 1st postion started with at 1/4 after making contact with the shell holder.
                Size a piece of brass ,then drop into chamber.Carefully feel for the case shoulder to make contact against chamber shoulder.
                Good friends will come bail you out of jail. A best friend will be sitting next to you in the cell saying damn that was fun!

                Comment

                • #23
                  highpower790
                  Veteran Member
                  • Jun 2013
                  • 3481

                  OP,once you get things in order,consider coming to the ca service rifle championship at Coalinga Rifle Club the 1st weekend of April,and then the highpower championship the 1st weekend of May.
                  Keep it simple!

                  Comment

                  • #24
                    devster55
                    Senior Member
                    • Nov 2012
                    • 2095

                    Originally posted by highpower790
                    OP,once you get things in order,consider coming to the ca service rifle championship at Coalinga Rifle Club the 1st weekend of April,and then the highpower championship the 1st weekend of May.
                    Unfortunately I have a intro to long range shooting course put on my the NCPPRC club at sac valley rifle range the first week of April but am down to go to the high power championships. Is there any regular service rifle matches?
                    Good friends will come bail you out of jail. A best friend will be sitting next to you in the cell saying damn that was fun!

                    Comment

                    • #25
                      smoothy8500
                      Veteran Member
                      • Sep 2009
                      • 3846

                      Originally posted by devster55
                      Some fall freely into the gauge and some the rim will not go in.
                      Looking at the first pic, do you have any nicks or bent rims? they will hang up on the case gauge. As for chambering, if they slide in and out that is good.

                      For proper chamber-check on an M1A/M14 use a stripped bolt to see if it closes on the sized brass. Avoid using the op-rod to "slam closed" which gives a false "OK" since the force of the spring can cram the bolt closed on an oversize piece of brass.

                      Comment

                      • #26
                        waveslayer
                        Senior Member
                        • Apr 2012
                        • 1728

                        If the brass has different OAL length it my resize differently, some times on LC brass I resize it twice because the "milspec" is just crap spec on some weapons

                        My wife thinks I only have 3 guns

                        Comment

                        • #27
                          fguffey
                          Senior Member
                          • Mar 2010
                          • 1408

                          You are using a case gage, a reloader should understand the case gage measures fired and unfired cases. I suggest you cull the cases that do not 'fall' in to the gage.

                          I make chamber gages, the chamber gages do not measure fired cases. And then there is a technique I have never read on this forum; That technique requires the reloader to reverse the case and stick the case head into the case gage. I could suggest the reloade measure the inside diameter of the case gage and then compare the inside diameter with the outside diameter of the case I do not believe it is going to happen.

                          Comment

                          • #28
                            stevec223
                            Senior Member
                            • Jul 2011
                            • 1620

                            Do you have a bolt action rifle available to check their fit ??... Easier to check brass with than a semiauto.. Also check head of brass for extractor burrs that could be holding brass from dropping in the case guage... Good luck...
                            Cheers...

                            Comment

                            • #29
                              fguffey
                              Senior Member
                              • Mar 2010
                              • 1408

                              Do you have a bolt action rifle available to check their fit ??... Easier to check brass with than a semiauto.. Also check head of brass for extractor burrs that could be holding brass from dropping in the case guage... Good luck...
                              Does he have a sizing die, the case can be reversed and then stuck into the die case head first. I understand; that just drove your guys to the curb but reloaders do not measure the diameter of the case head. The diameter of the case head, from the beginning started out smaller in diameter than the opening of the die body.

                              If the case head has been upset with heavy loads the diameter f the case will increase. And then there is extraction of heavy loads. I have shell holders that will sort cases with upset case heads etc.

                              F. Guffey

                              Comment

                              • #30
                                stevec223
                                Senior Member
                                • Jul 2011
                                • 1620

                                Originally posted by fguffey
                                Does he have a sizing die, the case can be reversed and then stuck into the die case head first. I understand; that just drove your guys to the curb but reloaders do not measure the diameter of the case head. The diameter of the case head, from the beginning started out smaller in diameter than the opening of the die body.

                                If the case head has been upset with heavy loads the diameter f the case will increase. And then there is extraction of heavy loads. I have shell holders that will sort cases with upset case heads etc.

                                F. Guffey
                                I was inferring to check his bad brass in a bolt action to confirm his case guage was good or bad,,, in a different but easier way... His die would also be checked this way for its resizing ability at the base of the case...
                                Your suggestion to reverse brass in case guage was a good one and noted...
                                I'm not here to "drive anyone to the curb"...
                                Cheers

                                Comment

                                Working...
                                UA-8071174-1