Unconfigured Ad Widget

Collapse

nOTHING hERE

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • moyneur
    Member
    • Jan 2012
    • 263

    nOTHING hERE

    nOTHING
    Last edited by moyneur; 05-22-2021, 5:56 PM.
    The difference between stupidity and genius is that genius has its limits
    ~~Albert Einstein~~

  • #2
    ruggyh
    Member
    • Mar 2012
    • 203

    Any loading will work fine out of your model V 460.

    If you want more specific information you should provide more information about the specifics about what you are trying to achieve. Best for What?

    Of coarse to really optimize your load you should take up reloading.

    be safe
    Ruggy

    Comment

    • #3
      moyneur
      Member
      • Jan 2012
      • 263

      Originally posted by ruggyh
      Any loading will work fine out of your model V 460.

      If you want more specific information you should provide more information about the specifics about what you are trying to achieve. Best for What?

      Of coarse to really optimize your load you should take up reloading.

      be safe
      Ruggy
      Been reloading for a number of years, mainly 357 and 44 mag, have done up some 460 and 454 loads w/ H110 and Enforcer w/ 240 fmj, checking to see if anyone has a good recipe that works with 5" barrel. Have a number of reloading manuals including Lee, Hornady, Seirra (that does not list 460), Lyman.
      The difference between stupidity and genius is that genius has its limits
      ~~Albert Einstein~~

      Comment

      • #4
        ruggyh
        Member
        • Mar 2012
        • 203

        As stated the barrel length is not that relevant with 460.

        Make sure the bullet you are using is rated for the velocity range you plan on pushing them.

        Suitable powders for true 460 performance are A9, 2400, Enforcer, N110, H110, Lil Gun, 4227; there are other suitable powders but these are most common and readily available.

        I would not recommend Lil Gun with light for caliber bullets as accelerated flame cutting may be observed; but with lead bullets 325 or greater it is the champ.

        H110 will out fps the rest under most conditions.

        Use a good crimp to ensure you won't experience any bullet creep.

        Here is a link to show you what the differences in barrel length performance in 460 S&W

        I have seen the question poised on several occasions. Most of us know that even the same barrel length revolvers will deliver a small difference because of a variety of factors. I decided to chrono each barrel length under the same conditions earlier this month. A few notes: • The 8.375” gun...


        Of coarse each gun has it own temperament that only hand loading can discover

        be safe
        Ruggy

        Comment

        • #5
          MongooseV8
          Veteran Member
          • Apr 2010
          • 4426

          I've gone through a lot of 460 components. And while the above is true as far as velocity using different loads in short versus long barrels, one thing that will be different is muzzle flash. H110 is going to create one heck of a blast out of the muzzle. I prefer Lil gun myself. Also H110 is very dirty and Lil gun seems to burn cleaner.

          Comment

          • #6
            moyneur
            Member
            • Jan 2012
            • 263

            Originally posted by MongooseV8
            I've gone through a lot of 460 components. And while the above is true as far as velocity using different loads in short versus long barrels, one thing that will be different is muzzle flash. H110 is going to create one heck of a blast out of the muzzle. I prefer Lil gun myself. Also H110 is very dirty and Lil gun seems to burn cleaner.
            I have notice that with 44's and 357's although if you want a flamethrower, 2400 takes the cake. Have only ran across a couple recipes for 2400 in 460 but quite a few for enforcer. I would have to say that 2400 is my first choice and enforcer is #2 with both 357 & 44 mag.
            The difference between stupidity and genius is that genius has its limits
            ~~Albert Einstein~~

            Comment

            • #7
              For54
              Junior Member
              • Apr 2014
              • 67

              I use heavy hard cast from matts bullets, bear tooth bullets, or xtp mag behind h110 and a magnum large rifle primer. Brass gets about 3-4 loads with h110, since h110 operates near max, then i throw into the reduce load bin. Bear tooth 405 grs behind max h110 always bring a smile. Light weight bullets with h110 seems like a waste in the 460v, big blast and fireball and not fun to shoot.

              For medium weight reduced loads i use aa-5744. Published Load data is available online. Matts 245 grain swc gas checked and hornady xtp works good for this.

              For lighter 45 colt level stuff out of a 460 mag case,, any cowboy 45LC bullet behind trail boss, or safe charges of red dot, unique have worked well, reliable and accurate as well. Load at your own risk.

              Starline brass is my goto. Any nickle plated lasts about 2-3 loads then splits at mouth. Havent tried hornady brand brass yet. Proper neck tension and crimp are essential to prevent bullet creep and proper ignition. Starline seems best for 3-4 loads.

              The 460v is a fine revolver and a great round to handload for, i perfer it over the 454 super redhawk.

              Comment

              • #8
                ruggyh
                Member
                • Mar 2012
                • 203

                Originally posted by For54
                I use heavy hard cast from matts bullets, bear tooth bullets, or xtp mag behind h110 and a magnum large rifle primer. Brass gets about 3-4 loads with h110, since h110 operates near max,
                Starline brass exceeded 40 reloads in my testing before becoming unserviceable- this was done with 50 grains H110 with 200FTX on top with average of 2200 fps at 52kpsi.

                Hornady brass typically fails at 8 reloads under same tests

                If your cases are splitting you are using to much bell especially with nickle plated cases.

                I should note that most factory loaded ammunition is loaded to 15% of MAP or around 54-55 kpsi, Hornady 200 FTX is loaded to around 57-58 kpsi

                If your case extraction is sticky or getting there you are at about 62kpsi

                Let case extraction be your guide to pressure issue

                Expect any reasonable 460 load to have flattened primers.

                Originally posted by For54
                Bear tooth 405 grs behind max h110 always bring a smile.
                Bullets this large are past the point of diminishing returns and of little value in the field; you will get max performance at about 345 grains.

                Shooting large lead is a range novelity at best- if you really want to go large get a BFR with it's 3" long cylinder you can shoot 740 grainer


                Originally posted by For54
                Light weight bullets with h110 seems like a waste in the 460v, big blast and fireball and not fun to shoot.
                Never had anyone shoot a 200 FTX and not like them

                While I don't recommend the 200FTX as a big game bullet, they will cut a coyote in two.

                The 200 XPB Barnes works fine when a light bullet is called for- thin skinned game.

                Most hunting would be well served with bullets between 240 and 325 grains of a well constructed bullet.



                When selecting bullets make sure they are rated for the velocity you plan to push then especially if terminal performance is important.

                In test years ago I had some jacketed bullet separate during testing.

                I don't recommend using fast powders for reduced reloads, see too many guns destroyed each year (usely the reloader fails to except he double charged).
                As mentioned Trailboss is your friend when for reduced loads or Tin Star if you can find it.


                be safe
                Ruggy

                Last edited by ruggyh; 11-26-2018, 7:16 PM.

                Comment

                • #9
                  SoCalSteven
                  Junior Member
                  • May 2017
                  • 10

                  Originally posted by ruggyh
                  Starline brass exceeded 40 reloads in my testing before becoming unserviceable- this was done with 50 grains H110 with 200FTX on top with average of 2200 fps at 52kpsi.

                  Hornady brass typically fails at 8 reloads under same tests

                  If your cases are splitting you are using to much bell especially with nickle plated cases.
                  Interesting info. I picked up 200 Hornady cases, plus the 100 I'll get from the factory ammo. If they last 8 loads the cost per round will still be acceptable. I'll have to get some Starline to try.

                  I see the wide range of projectiles in your photos. What are you loading with the 300gr options? I have the Speer Deepcurl and Hornady XTP Mag. For H110, Hornady's data is wide (33.4 to 39.2) and seems to avoid the top end, Speer seems way conservative (34-36), and Hodgdon is pretty hot. (38-42.5)

                  From a quick trial, 42.5gr of H110 seems to be pretty near 100% case capacity with either of the 300gr projectiles I have. With the feedback that H110 performs best near max and with a strong crimp it sounds like the bottom of Hornady's range would be dirty and poor performance?

                  Comment

                  • #10
                    ruggyh
                    Member
                    • Mar 2012
                    • 203

                    Originally posted by SoCalSteven
                    I see the wide range of projectiles in your photos. What are you loading with the 300gr options? I have the Speer Deepcurl and Hornady XTP Mag. For H110, Hornady's data is wide (33.4 to 39.2) and seems to avoid the top end, Speer seems way conservative (34-36), and Hodgdon is pretty hot. (38-42.5)

                    From a quick trial, 42.5gr of H110 seems to be pretty near 100% case capacity with either of the 300gr projectiles I have. With the feedback that H110 performs best near max and with a strong crimp it sounds like the bottom of Hornady's range would be dirty and poor performance?
                    42.5 is near 100% with 300 grain jacketed bullets.
                    The Hodgdon data follows their recommendation of not loading H110 below 90% case fill.

                    I typically load 300 XTP Mag, Deep Curls, and Swift with 38-38.4 grains and crimp in the cannelure. the Swift are a little longer and will produce a little more velocity (not much) with an increase of about 2kpsi over the 52kpsi I usually see.

                    I rarely load past 41.5 grains as extraction becomes sticky and groups don't improve any so I don't feel it is necessary. The 42.5 grains is a true max load.

                    While I have loaded H110 down to 80% in 460 without issue (with WLR primers ) I don't recommend it. I have had a number of local guys have problems with poor ignition and squibs when they down loaded below Hodgdon recommendations and once they under stand the issue and load at 90% + their issue go away.

                    If you really what a lighter load then the 38.2 grain range (about 1580 fps typical) then I would recommend 2400 and it is ok down to about 70% case fill. N110 is also a good powder and down load well- probably the cleanest burning powder especially at reduced loading. All the spherical powders burn best at higher pressure.

                    Of coarse the powder I listed above will all work with the 300 grain jacketed bullet - use good loading practice and start at the bottom and work up.

                    You will find the 460 S&W cartridge very forgiving in that accuracy is typically good over a wide range of loading and pushing the limits is not required to get good grouping.

                    The photo of bullets I posted is not all inclusive as there are other premium bullets for manufactures like North Fork Technologies and some additional Cutting Edge offers that offer premium terminal performance.

                    If terminal performance is important to you I would stick with monolithic constructed bullets or the Swift offering (they also have a 260 not pictured).

                    I have used most of the jacketed and monolith bullets in the picture in the field with success. Those mention above produced largest and most consistent wound channels.

                    My personal go to bllet currently is the 260 grain CPS from North Fork and was used on the Grizzly pictured below.

                    be safe
                    Ruggy

                    Comment

                    • #11
                      roc_my_tims
                      Senior Member
                      • Oct 2011
                      • 1530

                      H110, hornady bullets 300 grn. More info when i get to my bench

                      Comment

                      • #12
                        Mesa Defense
                        Senior Member
                        • Feb 2009
                        • 2172

                        Nice head on that bear.

                        Comment

                        • #13
                          ruggyh
                          Member
                          • Mar 2012
                          • 203

                          Thanks for the bear compliment.

                          Forgot to mention do not confuse Hornady 300 XTP with 300 XTP MAGs; the XTP is not suitable for 460 use except when used for reduced loads and even then it groups poorly compared to other jacketed bullets. Once again I urge hand loaders to make sure you don't push bullets beyond the design velocities.

                          I also failed to mention 4227 for use with the 300 grain jacketed bullets mentioned previously. It performs well and produces excellent groups and is clean burning compared to most of the spherical powders. It won't produce the velocity of Lil'Gun or H110 but as stated earlier you don't have to wring out every fps to get good groups. I have been using 4227 in the majority of my 300 grain bullets loads the last several years and find it produces the tightest groups (with 300 grain bullets) especially when you are shoot out past 100 yards.

                          be safe
                          Ruggy

                          Comment

                          • #14
                            moyneur
                            Member
                            • Jan 2012
                            • 263

                            This is great, looks like i'm on the right track, been kicking around a 300 gr pill. I have plenty of H110, Lil'Gun, 4227, Enforcer (alot), Trail Boss, and my favorite 2400.

                            Have any favorites for 454 Ruggy?
                            The difference between stupidity and genius is that genius has its limits
                            ~~Albert Einstein~~

                            Comment

                            • #15
                              SoCalSteven
                              Junior Member
                              • May 2017
                              • 10

                              Originally posted by ruggyh
                              42.5 is near 100% with 300 grain jacketed bullets.
                              The Hodgdon data follows their recommendation of not loading H110 below 90% case fill.

                              I typically load 300 XTP Mag, Deep Curls, and Swift with 38-38.4 grains and crimp in the cannelure. the Swift are a little longer and will produce a little more velocity (not much) with an increase of about 2kpsi over the 52kpsi I usually see.

                              I rarely load past 41.5 grains as extraction becomes sticky and groups don't improve any so I don't feel it is necessary. The 42.5 grains is a true max load.
                              From your experience, it sounds like the bottom end of Hodgdon's data is a reasonable place to start. If I wanted to get a handful of rounds to try out, perhaps a spread from 37 to 39gr would give a good start and none would be too hot?

                              Appreciate all the info. From that bear, the loads clearly did the job!

                              Comment

                              Working...
                              UA-8071174-1