Unconfigured Ad Widget

Collapse

Evolution Gun Works

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • #16
    smoothy8500
    Veteran Member
    • Sep 2009
    • 3846

    Originally posted by kcstott

    By the way and don't take offense to this just trying to keep you humble.
    Just because you been reloading for 40 years don't mean you been doing it right.
    Sometimes it's 40 years experience, or 1 year's experience 40 times over...

    Mixed brass and mixed rifles usually necessitate the small base die, which you are using. Now it's trying to find the cause of the "stuck round" situation. As you found, chamber checkers are not infallible. The rifle chamber(s) plunk test with a sized case is the true test. Not testing is a first-year mistake. Move on and find the true issue.

    Comment

    • #17
      rodsvet
      Member
      • Apr 2013
      • 225

      Thanks for the abuse guys.

      Comment

      • #18
        baih777
        CGN/CGSSA Contributor
        CGN Contributor
        • Jul 2011
        • 5680

        Originally posted by rodsvet
        Thanks for the abuse guys.
        Sorry not abuse. Just trying to help. That's a lot of bullets to pull apart.
        Been gone too long. It's been 15 to 20 years since i had to shelf my guns. Those early years sucked.
        I really miss the good old Pomona Gun Shows.
        I'm Back.

        Comment

        • #19
          Dragginpanda
          Senior Member
          • Jul 2014
          • 521

          Maybe those rounds will chamber in one rifle, but not the others. That might alleviate some of the frustration.

          Lack of company response is lack of company response.

          SemiAuto chambers are tricky. I go semiauto to bolt. If I need more semiautomatic brass, I don’t use mixed brass. Bolt can go mixed.

          Comment

          • #20
            kcstott
            I need a LIFE!!
            • Nov 2011
            • 11796

            Originally posted by rodsvet
            Thanks for the abuse guys.
            Remember the man that points a finger has three pointing back. And if you could kick the man in the arse responsible for your problems you wouldn’t sit for a week.
            You did this to yourself because you failed to do basic quality control.
            Last edited by kcstott; 03-31-2018, 5:01 PM.

            Comment

            • #21
              TexasJackKin
              Senior Member
              • Jul 2014
              • 718

              Originally posted by rodsvet
              Thanks for the abuse guys.
              This is CalGuns, that's what we're here for! You have a good Easter as well!
              Mike M.
              Dayton, NV
              NRA Life member
              Front Sight DG
              CRPA, USPSA, AOPA, EAA, CCW: NV, CA & AZ
              Yes, I'm related to Texas Jack

              Comment

              • #22
                Pardini
                Senior Member
                • May 2014
                • 1204

                Originally posted by rodsvet
                Thanks for the abuse guys.
                Post a B itch threads generally don't turn out well for the OP.

                Maybe that's why you didn't get a response from EGW as well.

                Now, if you asked for help understanding or resolving a issue or problem you have, you would likely receive considerably less "Abuse"
                Originally Posted by OCEquestrian View Post
                Excellent! I am thinking about it as well and I only have 4 points and an unfortunate "match bump" up to expert classification where I am far less "competitive" with my peers there.

                Comment

                • #23
                  McGuiver
                  Senior Member
                  • Feb 2016
                  • 1022

                  Evolution Gun Works

                  Originally posted by rodsvet
                  Beware of this company. They do not stand behind their case checkers. They say that if it will "plunk" in their checker, it will chamber in any AR. I have 2 FN barrels and three DS Arms Ar's and now have 6500 rounds to pull down and resize. They do not respond to emails or phone messages. Do business with them at your own peril!


                  Why are you using an aluminum anodized checker? Aluminum has a large thermal expansion coefficient. From freezing weather to 100+ degree F and loading in a garage, aluminum case gauge can grow and shrink.

                  Have you ever seen an aluminum head space gauge? I never have. They are all steel for precision and wear and tear.



                  Steel expansion coefficient is half that of aluminum. Why not try a slotted steel one. I love the my Sheridan ones.






                  Sent from my iPad using Tapatalk
                  Last edited by McGuiver; 03-31-2018, 8:37 PM.

                  Comment

                  • #24
                    FLIGHT762
                    Veteran Member
                    • Mar 2009
                    • 3072

                    A Redding S/B Body Die could likely repair the loaded rounds without pulling them down if your issue is shoulders not being bumped back far enough. I've done it a number of times.

                    Almost certainly a shoulder bump issue if the cases won't chamber in a 5.56 NATO chamber.

                    Is your press flexing too much? Is it mounted onto a solid table? That will cause issues as well.

                    Are you new to to loading rifle cases?

                    Comment

                    • #25
                      kcstott
                      I need a LIFE!!
                      • Nov 2011
                      • 11796

                      Originally posted by McGuiver
                      Why are you using an aluminum anodized checker? Aluminum has a large thermal expansion coefficient. From freezing weather to 100+ degree F and loading in a garage, aluminum case gauge can grow and shrink.

                      Have you ever seen an aluminum head space gauge? I never have. They are all steel for precision and wear and tear.



                      Steel expansion coefficient is half that of aluminum. Why not try a slotted steel one. I love the my Sheridan ones.






                      Sent from my iPad using Tapatalk


                      Because the temperatures involved won't mean a damn thing. You'd need a 100˚ F temp swing to even begin to see the shrinkage or expansion.

                      6061 with a CTE of .0000131 per F˚/inch linear = .0019" with a 100˚F swing So even in an extreme case you'd only see half that because the gauge was made in the 65˚- 85˚ range so for the gauge to be bad it would need to be either be -15˚ or 185˚. realistically you could expect a +/- 20˚ swing which would only change the chase checker .0004"

                      And here endith the lesson

                      Comment

                      • #26
                        McGuiver
                        Senior Member
                        • Feb 2016
                        • 1022

                        Evolution Gun Works

                        Originally posted by kcstott
                        Because the temperatures involved won't mean a damn thing. You'd need a 100˚ F temp swing to even begin to see the shrinkage or expansion.



                        6061 with a CTE of .0000131 per F˚/inch linear = .0019" with a 100˚F swing So even in an extreme case you'd only see half that because the gauge was made in the 65˚- 85˚ range so for the gauge to be bad it would need to be either be -15˚ or 185˚. realistically you could expect a +/- 20˚ swing which would only change the chase checker .0004"



                        And here endith the lesson


                        I know about the temperature swings, but I don't think anodized aluminum gauges are for the long term everyday reloader. They are cheap to manufacture, but for long term I like my steel ones. I know steel can wear too, but is all about the care of your gauges.

                        All my years working aerospace, we never had a aluminum gauge to check splines and such. They were always steel. I agree that your gauges should be checked with an outside reference to make sure they are good before running parts (loading). There was no first article inspection it seems. For some parts in aerospace we were required to do first article inspections every shift change, and spot check in between.

                        If this was a bad gauge that was used as a reference, then this is very sad. When I start loading a batch of ammo I always check my ammo against one of my gauges, and measure with appropriate measure device. Not doing this can lead to a hard lesson learned.

                        Linear expansion could be a problem is your gauge is at the max chamber size and it has grown beyond that, and that is what the what the ammo was loaded to.

                        We also don't know how worn the gauge could be. It could be out of spec from wear too. Was all ammo 100% case gauged? 6500 rounds could cause a lot of wear on the gauge at 100% gauging.

                        Sent from my iPad using Tapatalk
                        Last edited by McGuiver; 04-02-2018, 7:26 PM.

                        Comment

                        • #27
                          kcstott
                          I need a LIFE!!
                          • Nov 2011
                          • 11796

                          Originally posted by McGuiver
                          I know about the temperature swings, but I don't think anodized aluminum gauges are for the long term everyday reloader. They are cheap to manufacture, but for long term I like my steel ones. I know steel can wear too, but is all about the care of your gauges.

                          All my years working aerospace, we never had a aluminum gauge to check splines and such. They were always steel. I agree that your gauges should be checked with an outside reference to make sure they are good before running parts (loading). There was no first article inspection it seems. For some parts in aerospace we were required to do first article inspections every shift change, and spot check in between.

                          If this was a bad gauge that was used as a reference, then this is very sad. When I start loading a batch of ammo I always check my ammo against one of my gauges, and measure with appropriate measure device. Not doing this can lead to a hard lesson learned.

                          Linear expansion could be a problem is your gauge is at the max chamber size and it has grown beyond that, and that is what the what the ammo was loaded to.

                          We also don't know how worn the gauge could be. It could be out of spec from wear too. Was all ammo 100% case gauged? 6500 rounds could cause a lot of wear on the gauge at 100% gauging.

                          Sent from my iPad using Tapatalk
                          Well if you knew about temp swings and thermal expansion why did you post the statement? people here are going to think that a minor shift in temperature is going to cause a major shift in part size. People here don't deal with materials they I do. or possibly the way you do either. So why even bring something up that in the ten thousandths of an inch when what we are worried about is in the plus or minus .002" range

                          Depends on what the gauge is for. I have no problem with an Aluminum case gauge as long as it is made to a traceable standard and hard anodized. there is no reason to check 100% until well he found this issue then yeah every round needs to be checked.

                          Now this is going to sound contrary to what i posted a few post above but I've been reloading for close to 30 years and never needed a case gauge. I've never had a single round fail to chamber. I've had 45 ACP round that were seated to manual spec that were too long for the magazine in a 1911 so now my 45 ACP rounds are mag checked and so are every semi auto pistol round i make.

                          The guy has other issues and he has just failed to figure that out yet. it should not take 1/4 turn to get a rock chucker to cam over 1/16-1/8 turn at the most.

                          But he failed. he failed to do his due diligence and check his rounds periodically through the process. there is no shortcuts for QC
                          Last edited by kcstott; 04-02-2018, 8:25 PM.

                          Comment

                          • #28
                            divingin
                            Veteran Member
                            • Jul 2015
                            • 2522

                            Originally posted by rodsvet
                            Yes, I did do a trial fit for the first few. But once I got going, I just tried every third one in the checker. Some will chamber but the batch is not reliable.
                            Sounds like a process problem more than anything. Your rounds are coming off the line differently, which indicates one or more of the steps is not doing what it should be every time.

                            Comment

                            • #29
                              rodsvet
                              Member
                              • Apr 2013
                              • 225

                              I wish I had not put this post on the forum. But to be fair EGW has reached out and basically said they will repair, replace, refund after they inspect the checker. I originally was ticked because the had not returned my emails or calls. They do seem to be a stand up company that wants to help. Many of you have stated, their products are first class. Hey Cheep, I only sized them on a rockchucker after each shooting session. The reloading was done on an XL650. 6500 rounds on a rockchucker would have put me in the hospital for sure!

                              Comment

                              • #30
                                kteas1
                                Junior Member
                                • Aug 2015
                                • 94

                                Wow, now I'm second guessing reloading rifle lol. I've done lots of pistol. Guess I'll learn though. I already started the the brass processing rifle. 556/223 for an AR. I bought head space Guage, and the col guage. Also have a checker. Think I'm so done reading, then call the guy that installed my garage hanging storage racks, he reloads rifle for match shooting. Yup, in going to cheat and ask someone that knows how.

                                Comment

                                Working...
                                UA-8071174-1