Unconfigured Ad Widget

Collapse

Upside Down Primer

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • #31
    CSACANNONEER
    CGN/CGSSA Contributor - Lifetime
    CGN Contributor - Lifetime
    • Dec 2006
    • 44094

    Originally posted by jericho89
    If they are flipping going into the priming tube then you need to adjust how you are loading your tubes. On a Dillon (which is what he is asking about there) if you hold the pick up tube straight and tight against the primer tube before you pull the retention pin they will not flip.


    If they are flipping after they are leaving the priming tube then your machine is out of adjustment.

    I have 3 Dillon machines, have loaded over 20k rounds a year and have maybe flipped 2 primers a year (and I can not remember the last time I had one flip. If your technique is good and your machine adjusted correctly they do not flip.
    Agreed but, nevertheless, those are two other places, besides a worn or improperly sized priming tube, where a primer can flip in a Dillon priming system.
    NRA Certified Pistol, Rifle, Shotgun and Metallic Cartridge Reloading Instructor
    California DOJ Certified Fingerprint Roller
    Ventura County approved CCW Instructor
    Utah CCW Instructor


    Offering low cost multi state CCW, private basic shooting and reloading classes for calgunners.

    sigpic
    CCW SAFE MEMBERSHIPS HERE

    KM6WLV

    Comment

    • #32
      tonyjr
      Senior Member
      • Nov 2015
      • 1448

      I was told one of problem with primers is that if they
      hit the floor , they can bend .
      Don't try to use them .
      One bent one and you spend more time / money than
      if you saved and used a hundred of them
      Tape the ones that hit floor to cardboard and use pellet
      gun
      life member - CRPA and NRA
      All ways listen - after you can say I new that

      Comment

      • #33
        ojisan
        Agent 86
        CGN Contributor
        • Apr 2008
        • 11787

        Originally posted by jericho89
        If they are flipping going into the priming tube then you need to adjust how you are loading your tubes. On a Dillon (which is what he is asking about there) if you hold the pick up tube straight and tight against the primer tube before you pull the retention pin they will not flip.


        If they are flipping after they are leaving the priming tube then your machine is out of adjustment.

        I have 3 Dillon machines, have loaded over 20k rounds a year and have maybe flipped 2 primers a year (and I can not remember the last time I had one flip. If your technique is good and your machine adjusted correctly they do not flip.


        and the underlined part is important.

        Originally posted by Citadelgrad87
        I don't really care, I just like to argue.

        Comment

        • #34
          jdfthetech
          Member
          • Dec 2017
          • 189

          Originally posted by tonyjr
          I was told one of problem with primers is that if they
          hit the floor , they can bend .
          Don't try to use them .
          One bent one and you spend more time / money than
          if you saved and used a hundred of them
          Tape the ones that hit floor to cardboard and use pellet
          gun
          I have never had a primer bend from landing on the floor.
          I drop them quite often.
          I use CCI small pistol primers.

          Has anyone else ever heard of this?
          while (bullets > 0 && target == 1){fire == 1;}

          Comment

          • #35
            jericho89
            Senior Member
            • Aug 2011
            • 1129

            Originally posted by jdfthetech
            I have never had a primer bend from landing on the floor.
            I drop them quite often.
            I use CCI small pistol primers.

            Has anyone else ever heard of this?
            never seen one bent and I have stepped on them before... if your primers are so soft they are bending from being dropped I would be suspect of quality. Something that soft would likely pierce when fired.

            Comment

            • #36
              tonyjr
              Senior Member
              • Nov 2015
              • 1448

              As I posted , many years ago I was buying the cheapest
              I could find . Lots of problems and this was way before
              the internet . For the last 25-30 years I have only used CCI .
              You had to depend on books , friends and the people behind
              and in front of counter at gun store .
              I learned real quick to let others go 1st and just listen .
              Braggers and know it alls will step on their tongues within a
              few minutes .
              Now a days , just post the question and wait for an answer
              that makes sense - you will get at least 2 opinions and maybe
              a link to utube .
              life member - CRPA and NRA
              All ways listen - after you can say I new that

              Comment

              • #37
                Wookiee87
                Senior Member
                • Jul 2010
                • 622

                If I remember correctly; Dillon recommends to soak, in water, primer filler tube if you have a stuck primer. It renders it inert.
                Power tends to corrupt, and absolute power corrupts absolutely

                Comment

                • #38
                  CK_32
                  I need a LIFE!!
                  • Sep 2010
                  • 14369

                  Either throw it away.

                  Or be a cheap azz like me and carefully pop it out to not flatten it. Then reseat it to save that $0.002
                  For Sale: AR500 Lvl III+ ASC Armor

                  What's Your Caliber??


                  My Youtube channel

                  Comment

                  • #39
                    Lead Waster
                    I need a LIFE!!
                    • Sep 2010
                    • 16650

                    When a primer is installed the correct way, and a firing pin strikes the back of it, on the cup, the cup will dent into the anvil and crush the compound, which fires it.

                    When a primer is backwards, and you slowly push it out with a decapping pin, there is no resistance to the ANVIL because it's not seated in a primer pocket... so it SHOULDN'T go off and if you go nice and slow, it won't even dent the primer cup. This

                    Since the primer is a replacement for the original, it shouldn't be super tight in the pocket either.

                    So it's not as scary as you think.

                    Even if you push a properly seated primer out of a bad case (say you realize you primed a .380 case instead of a 9mm, if you do it slowly, it's fine since you are pushing the anvil up against the cup, but there is no resistance to the cup (like a firing pin).

                    the compound must be crushed between the two surfaces and I think when you deprime it, there is not crushing.

                    IMHO.
                    ==================

                    sigpic


                    Remember to dial 1 before 911.

                    Forget about stopping power. If you can't hit it, you can't stop it.

                    There. Are. Four. Lights!

                    Comment

                    • #40
                      tonyjr
                      Senior Member
                      • Nov 2015
                      • 1448

                      Before I was doing it by hand , I try the water , even
                      put in a 5 gallon bucket [ before when they were taller ]
                      waste of my time .
                      But then I had a Lee and had spare small and large primer
                      chutes .
                      life member - CRPA and NRA
                      All ways listen - after you can say I new that

                      Comment

                      • #41
                        jtake
                        Member
                        • Feb 2011
                        • 367

                        Please be aware that oil and WD40 are likely NOT going to deactivate a primer.

                        Link to someone testing the notion that they will (about half way down, post #37).

                        Removing and killing primers IMX, primers are NOT killed by oil. There is a sad case, however, of a LEO who regularly cleaned his loaded mags with WD-40 (which has a penetrant) and his rounds failed him when he tried to stop an armed bank robbery in progress. Having heard of that, I have...


                        Quick summary, they soaked 10 primers from various manufacturers overnight with a variety of liquids (WD40, Hoppes #9, acetone, water, MEK, oil, motoroil, case lube, Hornady Oneshot) and at best, just few of one manufacturer's primer did not fire, with all or almost all otherwise going bang.

                        Maybe not a strictly scientific study, but one that suggests that you not expect to deactivate a primer by soaking it with some liquid.
                        Last edited by jtake; 01-29-2018, 3:01 PM. Reason: Typo for bang!

                        Comment

                        • #42
                          tonyjr
                          Senior Member
                          • Nov 2015
                          • 1448

                          Yes , I tried bleach and ammonia to .
                          Now they get taped to cardboard and shot with a pellet gun .
                          life member - CRPA and NRA
                          All ways listen - after you can say I new that

                          Comment

                          • #43
                            Chief-7700
                            Veteran Member
                            • May 2008
                            • 3382

                            So much for inspecting your loaded rounds before shooting them.

                            XL-650 to feed the: .45ACP's Les Baer Concept V, Ruger SR 1911, Ruger Nightwatchman,custom built Colt M1911, Springfield .45ACP Loaded.. 9MM SA Range Officer,Ruger P-85, Springfield Stainless 9MM loaded, SA 9MM 5.25" XDM, Springfield 9mm Stainless Range Officer, STI double stack .45ACP.
                            IDPA A41750 Safety Officer
                            NRA Certified RSO
                            "Stay out of the deep end of the pool; correct the problem with your credit card, not your dremel!"

                            Comment

                            • #44
                              One in the pipe
                              Member
                              • Nov 2017
                              • 147

                              Thanks again all for the comments. This is a lot of great info to go by.

                              I still have the round. I'll pull/pop the bullet out and just press the primer out. I'm sure it'll be fine.

                              Comment

                              • #45
                                Grampz
                                Member
                                • Jan 2010
                                • 378

                                I started out with a Lee Pro 1000. Geeze what a POS. It would flip 'em over randomly AND smash them in sideways sometimes! I have no idea why those didn't go off. That's quite a sight. I ended up hand priming everything on that press.
                                They say nothing is impossible. Well heck! I do the impossible everyday...

                                Comment

                                Working...
                                UA-8071174-1