Unconfigured Ad Widget

Collapse

Issues with 223 Keyholing???

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • #31
    baih777
    CGN/CGSSA Contributor
    CGN Contributor
    • Jul 2011
    • 5680

    Try. The hornaday 55g hpbt.
    Been gone too long. It's been 15 to 20 years since i had to shelf my guns. Those early years sucked.
    I really miss the good old Pomona Gun Shows.
    I'm Back.

    Comment

    • #32
      alexisjohnson
      Senior Member
      • May 2016
      • 651

      Boom....isolated the issue!

      It was a bad batch of Berrys bullets (FMJ).

      I took a sample of that specific batch of bullets i'd been using, took a 2nd sample from another batch of berrys bullets, and took a 3rd sample of sierra 55 grain FMJ's. I used a midrange of 23 grains of TAC at 2.20 OAL.

      Even using another AR (which i know to be very accurate), I was getting 5-6 MOA with the old batch of berrys, 1.5 MOA with the new Batch, and 1.25 MOA with the Sierras.


      With this new AR, i only got one bullet to keyhole but this is a much more precision platform than the other ar (BCM chrome lined). This same pattern repeated itself with the BCM. Every ammo i used was fine until i'd get to this batch of Berrys.

      This sucks royally as i'm sitting on 3.5k of these bullets. I'll tread carefully...testing each batch before committing. After that...i'm done with this brand. If i can't be 100% sure about base quality control...i'm not going to waste my time with them. Ive spent the past 2 weeks pulling my hair trying to figure out whats wrong.

      I've also developed a good set of protocol for if this happens in the future so i don't waste so much time and money.

      Thanks again everyone for you help.

      Comment

      • #33
        dwalker
        Veteran Member
        • Jul 2014
        • 2714

        Originally posted by alexisjohnson
        Boom....isolated the issue!

        It was a bad batch of Berrys bullets (FMJ).

        I took a sample of that specific batch of bullets i'd been using, took a 2nd sample from another batch of berrys bullets, and took a 3rd sample of sierra 55 grain FMJ's. I used a midrange of 23 grains of TAC at 2.20 OAL.

        Even using another AR (which i know to be very accurate), I was getting 5-6 MOA with the old batch of berrys, 1.5 MOA with the new Batch, and 1.25 MOA with the Sierras.


        With this new AR, i only got one bullet to keyhole but this is a much more precision platform than the other ar (BCM chrome lined). This same pattern repeated itself with the BCM. Every ammo i used was fine until i'd get to this batch of Berrys.

        This sucks royally as i'm sitting on 3.5k of these bullets. I'll tread carefully...testing each batch before committing. After that...i'm done with this brand. If i can't be 100% sure about base quality control...i'm not going to waste my time with them. Ive spent the past 2 weeks pulling my hair trying to figure out whats wrong.

        I've also developed a good set of protocol for if this happens in the future so i don't waste so much time and money.

        Thanks again everyone for you help.
        Contact the good folks at Berrys and give the lot #etc and see what they can do for you.
        Fear is the spare change that will keep you broke

        Call him run-like-hell-when-shtf-guy or dial-911-guy but NEVER call an unarmed man "Security".

        Comment

        • #34
          alexisjohnson
          Senior Member
          • May 2016
          • 651

          I just wanted to update everyone on this issue. I ended up returning the bad batch of berrys and replaced them with Hornady FMJ...they're virtually the same price.

          I had also sent in the BCM upper for the company to take a look at it and they reported back that the barrel was shot out (with around 1.5-2k) through it. They sent me a long thing about not firing over 12-15 shots per minute etc... and they ended up replacing the barrel 'as a one time courtesy'.

          My typical rate of fire was about 5 shots per minute and i'd go through 100-150 rounds in a typical session. I certainly don't do mag dumps or anything like that. Gun does get pretty hot after 150 rounds but nothing crazy. My reloads are always at the mid range level....for plinking i have zero reason to approach max loads.

          In any case, the whole thing has been quite strange...perhaps a wierd combo of bad bullets ended up ruining the barrel? Who knows..

          In any case, its all been resolved now. Thanks again for the help!

          Comment

          • #35
            pacrat
            I need a LIFE!!
            • May 2014
            • 10287

            (with around 1.5-2k) through it.
            At that count, you could expect some throat erosion. But certainly not shot out to the point of key holing.

            Crap Happens. This time the crap landed on you. It was a bum barrel from the get go. [likely soft steel] Glad they made it right for you.


            JM2c

            Comment

            • #36
              Oldjedi
              Member
              • Sep 2013
              • 338

              Other Factors

              If indeed the barrel was eroded, there may be other factors at play. I have seen many people use brasso or similar compounds to put a shine on the cases while tumbling. The grit should be washed out thoroughly specially from inside the case. Otherwise it will act as sandpaper inside the barrel when it blows out with the gases. Just another 2 cents worth.

              Comment

              Working...
              UA-8071174-1