Unconfigured Ad Widget

Collapse

New reloader

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • mmartin83
    Junior Member
    • Jan 2012
    • 38

    New reloader

    Hey guys the wife got my a single stage press from RCBS. I'm going to be reloading 9mm/30-30/ and 556. I was wondering what type of primers and powders you all use? Any insight would be helpful. Merry Christmas!!!
  • #2
    Crunchy_Taco
    Banned
    • Apr 2009
    • 183

    Get Lyman s book it will teach you everything

    Sent from my SAMSUNG-SM-G900A using Tapatalk

    Comment

    • #3
      8mmFMJ
      Calguns Addict
      • Aug 2011
      • 7405

      Any powder and any primer I can find load data for in the case I am reloading.

      Get what you can it's hard to come by now that ammo can't be imported.

      Comment

      • #4
        chrometip78
        Member
        • Jul 2009
        • 301

        I like powders that work across several calibers for simplicity.

        Unique/Universal works for my 9mm, 45acp, and 44. I've used and like Reloader 15 for 223 & 30-30.

        Mostly use CCI primers but have had success with Remington and Winchester primers also.

        Sent from my SAMSUNG-SM-G890A using Tapatalk

        Comment

        • #5
          Christopher761
          Senior Member
          • Nov 2014
          • 855

          For the rifles, you want to work up a load that works great for YOUR rifle. Small differences in ammo make big differences at long range. If you are only shooting out to 50-100 yards, then it might not be that big of a deal.

          As far as close range practice ammo, use anything you can find load data for. Especially 9mm.

          Some pistols have light primer strikes on certain hard primers. In which case, your experience will vary.

          Any 223/556 primer will work with a mil spec trigger.

          As far as powders, it depends on how you are charging the case. If you have a volumetric dispenser, then you want a powder that looks like sand, also known as "ball powder." For 9mm: Win231, CFE Pistol. There are many.

          I once bought a big jug of 800x. It works ok for 45. But each load has to be hand charged. It looks like and meters like corn flakes. No auto dispenser worked very well for me.

          For 30-30, I have no experience, and can't comment.

          For 223, I have used CFE223, and it metered and worked great. There are many powders made for this cartridge, but I don't have a lot of experience with other powders.

          A reloading bible is a good choice. Lymon or Lee would be great.

          Comment

          • #6
            Divernhunter
            Calguns Addict
            • May 2010
            • 8753

            Just get mag primers for all loads. Do not worry about the people who claim the sky-is-falling if you use the for all loads. Been doing so for many years. Win, CCI, Rem, Fed are all I have used and all have been fine.

            Get the Lyman #49 or 50 manual and read it. That will answer most of your questions.
            You will not find one powder to do all. Especially between pistol and rifle.

            9mm powders and there are more. Win231, Unique, Hi-Skor 700X,

            Only one I have used for 30-30 is IMR3031

            223/5.56--Win748(my #1 choice), H335, Benchrest, IMR4198,CFE 223

            Get Carbide pistol dies and you do not need to lube cases.

            Get RCBS SPRAY LUBE for rifle brass. Toss them into an old baking dish(metal is best) --give them a couple of squirts---shake and another couple of squirts and start sizing. Get some into some of the case necks to lube the expander ball. Tumble to clean off the lube. Check and clean primer pockets/flash holes then Hand prime.
            A 30cal will reach out and touch them. A 50cal will kick their butt.
            NRA Life Member, NRA certified RSO & Basic Pistol Instructor, Hunter, shooter, reloader
            SCI, Manteca Sportsmen Club, Coalinga Rifle Club, Escalon Sportsmans Club, Waterford Sportsman Club & NAHA Member, Madison Society member

            Comment

            • #7
              davek8s
              Senior Member
              • Jan 2011
              • 2014

              I use Win 231 for all of my pistol reloading 9, 38, and 45.

              For 223 I use CFE 223.

              My friend's dad me to reload and he used CCI primers so that's what I've always bought. Although I have used Remington, Winchester and S&B primers along the way. I really can't tell the difference between any of them.

              Comment

              • #8
                stilly
                I need a LIFE!!
                • Jul 2009
                • 10685

                Originally posted by mmartin83
                Hey guys the wife got my a single stage press from RCBS. I'm going to be reloading 9mm/30-30/ and 556. I was wondering what type of primers and powders you all use? Any insight would be helpful. Merry Christmas!!!
                I think it is doubtful that you will make 9mm for very long on that press. .556 might even follow...

                You will want at least a Lee Classic Turret or go progressive.
                7 Billion people on the planet. They aint ALL gonna astronauts. Some will get hit by trains...

                Need GOOD SS pins to clean your brass? Try the new and improved model...



                And remember- 99.9% of the lawyers ruin it for the other .1%...

                Comment

                • #9
                  MrElectric03
                  Senior Member
                  • Jul 2010
                  • 1590

                  First you'll need a manual before going any farther.

                  For primers I tend to stick to cci. In CA if it's as bad as I hear you'll want to pick up any that you find.

                  Powder I use hs6 for 9mm, and imr3031 for .30-30 and .223. Again though, if you find a load in a published manual and find the powder, buy it.
                  Originally posted by ar15barrels
                  So you are throwing out 95% of reality to select the 5% of reality where you are actually right?
                  We must be on calguns...

                  Comment

                  • #10
                    mmartin83
                    Junior Member
                    • Jan 2012
                    • 38

                    Originally posted by stilly
                    I think it is doubtful that you will make 9mm for very long on that press. .556 might even follow...

                    You will want at least a Lee Classic Turret or go progressive.

                    funny thing is that I was looking at getting a progressive press orginaly, however she surprised me with this.

                    Comment

                    • #11
                      Metal God
                      Senior Member
                      • Apr 2013
                      • 1839

                      Stilly is right , I loaded rifle for years on a single stage before loading pistol . It took about 4 months of loading 9mm & 45acp before I got a Classic turret press because it's just two slow on a single stage . 1.5 years after that I'm now looking to go progressive for my 9mm , 45 acp & 223 plinking loads Because the turret press is just to slow lol.

                      When I say slow I'm saying time consuming . I don't have an issue sitting at the bench for 2hrs at a pop . My issue is with the relative small amount loaded in that time . In ten minutes I can burn through ammo that took an hour to load . Not a good ratio .

                      That said don't ever sell the single stage . It's always good to have one around .

                      When I started loading I looked in the manual at the calibers I was going to load and bought the powder/s that where used in as many of the same cartridges .

                      So get your self a Manual ( Lyman"s 50th ) and see what are some of the same powders both the 30-30 and 223 use . IMR 4895 , H-335 , BL-C2 etc

                      Same goes with 9mm so Titegroup , Unique , HP-38/W231 etc will load many different hand gun calibers .

                      As for primers , They all work just fine really and when starting out just get what you can find but don't buy more then 1k at a time until you know that's the primer for you . In 223 and "if" you really are asking AR 223/5.56 you should use the CCI #41 primers but I almost exclusively use just standard CCI #400 SR primers in all my AR loads with out issue .

                      Just take it slow and at first don't over buy any one component until you know that's the one that works best for your application .
                      Last edited by Metal God; 12-26-2016, 6:23 PM.
                      Tolerate
                      allow the existence, occurrence, or practice of (something that one does not necessarily like or agree with) without interference.

                      Anyone else find it sad that those who preach tolerance CAN'T allow the existence, occurrence, or practice of (something that they do not necessarily like or agree with) without interference.

                      I write almost everything in a jovial manner regardless of content . If that's not how you took it please try again

                      Comment

                      • #12
                        mmartin83
                        Junior Member
                        • Jan 2012
                        • 38

                        Thanks for all the help guys. Pretty sure you all remember when you first started off and was looking for somewhere to start.

                        Comment

                        • #13
                          Ranchogunner
                          Member
                          • Jun 2016
                          • 125

                          Originally posted by mmartin83
                          Thanks for all the help guys. Pretty sure you all remember when you first started off and was looking for somewhere to start.

                          Well the "somewhere to start" for me was to get the Lyman manual and the Speers manual and read most of the first parts, then watching a ton of YouTube videos before loading the first round.

                          For powder I use Bullseye, Titegroup or Unique for 9mm and all pistol, and Xterminator and TAC for 223/556. 30-30? I don't load.

                          Primers -- CCI if you can get them. If not Winchester or Federal.

                          If I were you I would focus on acquiring powder first, because it can be hard to find periodically. If you are anywhere near the Sacramento area I could tell you the gun stores that usually have powder in stock. If the price is not to high, it is always better to buy your gunpowder and primers at a store, so you don't have to pay the hazmat fee for shipping.

                          Comment

                          • #14
                            stilly
                            I need a LIFE!!
                            • Jul 2009
                            • 10685

                            Interesting. I could have SWORN that I said to NOT sell the single stage off when I edited my answer earlier on when there were issues in the internets at mah house...

                            By all means, RTFM and LEARN on that single stage. DO NOT MOUNT that progressive until you have made several hundred loads and tested them on the single stage. THEN if you want to go faster, you can mount that progressive, get your load dialed in and pull away. But FIRST, learn to use that single stage.
                            7 Billion people on the planet. They aint ALL gonna astronauts. Some will get hit by trains...

                            Need GOOD SS pins to clean your brass? Try the new and improved model...



                            And remember- 99.9% of the lawyers ruin it for the other .1%...

                            Comment

                            • #15
                              Socalman
                              Senior Member
                              • Apr 2010
                              • 1339

                              When I first started my reloading it was 2012/2013 and there was not a lot of choice in powderrs --- or any components at the time. I would check Turners, Fowlers Gun room, Ammo Bros and other places and nobody had powder. Buying online was a possibility but the cost for 1 pound and the hazmat charge was huge, I did not know if I would do much of it. I finally scored my first pound of Power Pistol and CCI primers at Fowlers. You may have to start with what you can find unless you are willing to buy in bulk.

                              As others have said, buy the manuals; yes plural. Look at the online sites too. You can't be too careful in this hobby. Heck, what am I saying, I am still a noob at this.

                              Comment

                              Working...
                              UA-8071174-1