Unconfigured Ad Widget
Collapse
|
|
|
|
|
|
|
|
Reload Testing?
Collapse
X
-
7 Billion people on the planet. They aint ALL gonna astronauts. Some will get hit by trains...
Need GOOD SS pins to clean your brass? Try the new and improved model...

And remember- 99.9% of the lawyers ruin it for the other .1%... -
So did you use published data for the powder and bullet you are using, and did you cross check that with (at least) a second source of published data? And did you stay away from the maximum loads and start with a medium or light load? If you did that, then there should not be anything to really worry about. If you DID NOT do that, and just guessed at the gunpowder to use, and how much of it to use, then there is a whole lot to worry about. But I cannot imagine anybody doing that.
Also did you pay very close attention when you were loading that the powder was dispensing properly? If you don't have one, I would recommend using a powder checker to make sure you don't dump 2 loads or no loads into a case. I use the RCBS powder checker for rifle, and the RCBS lock out die for pistol.Comment
-
Okay so here is how you can give yourself a HUGE boost of confidence and maximize your success at testing ladders...
1. As already stated, Gather information on the load you want to make. PUBLISHED data is what you want, like from the manufacturer's website or reloading books. Cross check each with each other if you so desire. It helps but make certain that they are talking about the same powders and projectiles.
2. Write down the min and max loads. If you see two places that list different starting and max loads, pick the load range that BOTH OF THEM HAVE and start at the bottom. OR, start about .1gr about the bottom (because nobody starts at the very bottom anymore...).
3. Once you have decided on the load to start with, document it on an index card or load card. Then, follow your documentation and build the load according to what you wrote down.
4. I will prime the brass and then pull it off of my turret and tare it out on my American Weigh Gemini 20 digital scale. Then I will trickle in the amount of powder I need, THEN, I will dump it into a pan, see that the shell case makes the scale return to zero again, then pour the powder into the shell and see that the result is repeatable. Sometimes there is a slight variance of .02-.04gr but rarely. Then place it back into the turret.
5. Seat to the desired and predetermined depth, then crimp. Your depth means your COAL should be no shorter than the shortest in the books you pulled data from, but if you have two books stating slightly different starting points, the longer COAL will give you less pressure, so you may want to start there and work your way shorter. I did that with several of the 105gr SWC in 9mm.
6. On game day, I treat those bullets as all others. I load them, point and shoot. If you act funny, your ammo will catch on and think something is wrong and then you are doomed...
And there ya have it. Just act normal and check your documentation and all that you did in performing it correctly and you should be fine.Last edited by stilly; 12-15-2016, 9:28 PM.7 Billion people on the planet. They aint ALL gonna astronauts. Some will get hit by trains...
Need GOOD SS pins to clean your brass? Try the new and improved model...

And remember- 99.9% of the lawyers ruin it for the other .1%...Comment
-
hey guys, I've put together my loads... I'd love to hear the feedback in hopes of catching some big mistake that might cost me...
Honestly I read that I should "log" but wasn't 100% sure of what exactly to capture. So I'm sure there's some things that don't really matter, but just trying to make sure my first rounds won't ruin my life/gun.
Log-
Finished rounds
I found that I made mistakes in reading the scale (increments of 5 or 10?) so I had to go back to my log many times and update it cuz when measuring the power/case (all though I measured each powder charge at 23-24.5 gr) it was a few (like 5gr) off.. but that was because of my inability to read the scale :/
and
Look forward to what anyone has to say...Comment
-
good explanation Stilly... I had heard that a double-charge is probably the most dangerous thing, so what i did was weigh the case w/o power, then weight it with powder. Knowing that it should be 23 (min) heavier.
I basically weight and measured at every step.
As this was my first time dumping powder into cases, my first time I couldn't believe how much powder I was dropping. the funnel I was using didn't seem to fit like I would have liked over the .223 case (I assumed it would sit slightly inside the case (experience w/ pouring oil in a car, like). Buy my funnel sat flush and maybe a tiny bit outside the case. So I had to be very careful. (so now I'm thinking I'm skimping my load). But again, I measured the weight after, so hopefully that puts a "check mark" over that question.
BTW, my funnel is an RCBS 22-50cal funnel. Is there no attachment for the bottom that makes is pour directly into the case?
I hate to say this, but.... I do have some extra parts from my kit that I have yet to know what they're for

So why not put em here and maybe if they're IMPORTANT and someone knows you can let me know.
Cleaning looking (I actually used this a little to clean my primer pockets) but is that for the the inside of the casing?
Green plastic that is very similar to what I put below my powder measure... is it just a different size ummm (powder measure dispenser thingy)?
No idea what the large nut and blk items are in the bag
Comment
-
My God, even the Conservatives are liberal in the messed up StateComment
-
I donned a flak jacket, plate carrier and a helmet, put my pistol into a Ransom Rest with a long string, dug a foxhole 50' away and yelled out, "Fire in the hole" and yanked on the string as I flew through the air, leaping into a slow motion tactical roll into the foxhole. Man, did people look at me. Better safe than sorry I always say.NRA Certified Metallic Cartridge Reloading Instructor, Shotgun Instructor and Range Safety Officer
sigpicComment
-
Pics or GTFO.I donned a flak jacket, plate carrier and a helmet, put my pistol into a Ransom Rest with a long string, dug a foxhole 50' away and yelled out, "Fire in the hole" and yanked on the string as I flew through the air, leaping into a slow motion tactical roll into the foxhole. Man, did people look at me. Better safe than sorry I always say.
Active Army 1976-1986, Army Reserve 2005-2015, Afghanistan 2010-2011
http://www.thepolemicist.net/2013/01...t-for-gun.html
https://www.thereligionofpeace.com/Comment
-
WHOA WHOA! Five grains off? Or do you mean half a grain (0.5) grains, which is still a lot. In reloading decimals matter. Are you using a balance beam scale or an electronic scale?hey guys, I've put together my loads... I'd love to hear the feedback in hopes of catching some big mistake that might cost me...
Honestly I read that I should "log" but wasn't 100% sure of what exactly to capture. So I'm sure there's some things that don't really matter, but just trying to make sure my first rounds won't ruin my life/gun.
Log-
Finished rounds
I found that I made mistakes in reading the scale (increments of 5 or 10?) so I had to go back to my log many times and update it cuz when measuring the power/case (all though I measured each powder charge at 23-24.5 gr) it was a few (like 5gr) off.. but that was because of my inability to read the scale :/
and
Look forward to what anyone has to say...
The green translucent tube is for the bottom of the powder drop. There should be 2 of them. One for larger necks (such as .308, etc) and one for smaller (.223). Use the right one or you'll get spills. The brushes are for cleaining inside of cases. Again one for big cases & one for small. The black parts are for the in-press primer setup. The nut probably for the powder dropper, although mine looks different.
HIghly recommend you get an electronic scale if you don't already have one. Makes measuring much quicker, and you can just tare (zero) out the case weight and measure the charge weight easier.---------------------
"There is no "best." If there was, everyone here would own that one, and no other." - DSBComment
-
If you have followed proper loading procedures all will be fine. Hint there is no need to use max powder charges.I started loading in the middle 70's with a Rock Chucker and then in 1991 moved to a Dillon 550 and load a total of about 5,000 rounds of 9mm, 38 sp, 40S@W, 45 acp, 223, 30-06 and 300 Weatherby mag. loading is very easy you just have to be precise concise and exact. A loading manual should be the Bible for reloading. If you screw up it is you that screwed up.Just began reloading, going to actually fire them in the next few weeks...
What advice does anyone have?
Working off of the assumption that once you're at the range, it's too late to be cautious w/ firing your reloads. Can I be any safer while firing? Safety glasses?, Gloves? I"m shooting an AR style rifles, so maybe not put my face right behind the sights?
I'm trying to be super cautious, and during reloading (I've loaded up 15 cartridges **VERY FIRST 15) and I've logged everything I could to ensure no mistakes have been made. But now that all the "technical" manufacturing is over... What can I do to be more safe at the range given these are my first reloads?
Appreciate the help...Last edited by Sunday; 12-16-2016, 6:56 PM.California's politicians and unionized government employees are a crime gang that makes the Mexican drug cartels look like a Girl Scout Troop in comparison.Comment
-
Reloading is about attention to detailOkay so here is how you can give yourself a HUGE boost of confidence and maximize your success at testing ladders...
1. As already stated, Gather information on the load you want to make. PUBLISHED data is what you want, like from the manufacturer's website or reloading books. Cross check each with each other if you so desire. It helps but make certain that they are talking about the same powders and projectiles.
2. Write down the min and max loads. If you see two places that list different starting and max loads, pick the load range that BOTH OF THEM HAVE and start at the bottom. OR, start about .1gr about the bottom (because nobody starts at the very bottom anymore...).
3. Once you have decided on the load to start with, document it on an index card or load card. Then, follow your documentation and build the load according to what you wrote down.
4. I will prime the brass and then pull it off of my turret and tare it out on my American Weigh Gemini 20 digital scale. Then I will trickle in the amount of powder I need, THEN, I will dump it into a pan, see that the shell case makes the scale return to zero again, then pour the powder into the shell and see that the result is repeatable. Sometimes there is a slight variance of .02-.04gr but rarely. Then place it back into the turret.
5. Seat to the desired and predetermined depth, then crimp. Your depth means your COAL should be no shorter than the shortest in the books you pulled data from, but if you have two books stating slightly different starting points, the longer COAL will give you less pressure, so you may want to start there and work your way shorter. I did that with several of the 105gr SWC in 9mm.
6. On game day, I treat those bullets as all others. I load them, point and shoot. If you act funny, your ammo will catch on and think something is wrong and then you are doomed...
And there ya have it. Just act normal and check your documentation and all that you did in performing it correctly and you should be fine.
Develop a system, make a pre-check list and make debrief notes, down the road, the notes may help you
I run an excel spreadsheet with all the minutia of detail. I makes notes on any issues that I may have had, whether a load felt a little hot or under powered and any press related issues. I also tally the money saved on each round
I add up the columns for the year and know how many bullets to buy when they are on sale for next year
Most important rule is only one powder to the loading bench
Same with primers, check and recheck to make sure they are rifle, small pistol or small pistol magnum etc
I always recheck the published load data, even if I loaded the same load a week earlier
I clean up 100% before changing calibers and I always empty the powder hopper. If I load and pull a bullet the same day, I will re-use the powder. Otherwise I throw the powder away, even if I know what the load is from my box label or spreadsheet
I use a progressive, so notes are important when learning the characteristic of the machine. They are also helpful in preventing the same future mistake
Good luck, reloading is fun and I find it relaxing"While it may come as a surprise to the authors of the legislation, most semi-automatic pistols do in fact come with a pistol grip"Malthusianism is the idea that population growth is potentially exponential while the growth of the food supply is arithmetical at best.Comment
-
I load on a turret press. With 223 rounds I separate brass so it matches. Hopefully improving accuracy but also making it so I can simply weigh finished rounds two at a time to see if there is a variance in weight that can't be attributed to case, projectile, or "acceptable" charge differences. If it's more than 1 grain per complete round it goes in the inaccurate load bin. If it's over 1.6 grain I break it down.
I measure each powder charge for 308 individually though.Comment
-
Maybe I'm different. But I didn't find my first reloads to be intimidating.
If you are sure you used a proper powder with anything not near the max, it will just work. Physics is physics.
The biggest fear is the double charge, and you seem to have double and triple checked for that along the way.
Choot 'em. If fearful, take a friend who can drive you to the hospital if you end up with a face full metal, but I usually do this completely alone. I find the alone time peaceful.
Comment
Calguns.net Statistics
Collapse
Topics: 1,870,745
Posts: 25,175,444
Members: 358,862
Active Members: 5,389
Welcome to our newest member, 1776 Arms.
What's Going On
Collapse
There are currently 29399 users online. 95 members and 29304 guests.
Most users ever online was 239,041 at 11:39 PM on 02-14-2026.

Comment