Unconfigured Ad Widget

Collapse

.50 AE Reloading

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • KC001
    Junior Member
    • Jan 2016
    • 57

    .50 AE Reloading

    Hey all,
    I've been shooting my desert eagle for a while now and I think I'm ready to get into reloading for the big boy. I reload for the .44 mag using Win 296 and Winchester large pistol primers. I will be using a single stage rock crusher press because I want to take my time. I was hoping for some opinions on dies (RCBS, Lee, or Hornady), bullets, favorite loads, and maybe some tips and tricks to reloading the .50. I have been told that no matter which brand I go with, I'm still going to have to get a separate crimping die because the crimp/seating die doesn't cut it.
    Thanks
  • #2
    stilly
    I need a LIFE!!
    • Jul 2009
    • 10685

    Originally posted by KC001
    Hey all,
    I've been shooting my desert eagle for a while now and I think I'm ready to get into reloading for the big boy. I reload for the .44 mag using Win 296 and Winchester large pistol primers. I will be using a single stage rock crusher press because I want to take my time. I was hoping for some opinions on dies (RCBS, Lee, or Hornady), bullets, favorite loads, and maybe some tips and tricks to reloading the .50. I have been told that no matter which brand I go with, I'm still going to have to get a separate crimping die because the crimp/seating die doesn't cut it.
    Thanks
    You are already about 90% there...

    Just get the Lee dies because NOBODY makes a cheap and affordable Carbide die for .50 AE.

    No matter what, you gotta lube...

    So pick up some Hornady UNIQUE. Lee Steel dies worked FINE for me when I reloaded some 50 AE for someone some time ago. Of course they had no powder in their rounds, but they just wanted pretty looking ammo.

    BTW, I used the Lee Bullet Seater/Crimper and it worked just fine... Musta been someone who had a Dillon that told you that nonsense...

    Also, I think you should look for AA1680. I heard THAT was some good stuff in .50 AE...

    Component wise though you might be best with FMJ or TMJ in .500 and I am thinking 335gr or less, down to about 300gr. Plated? You can try Berry's but I think their pills look like crap. Rainier might make some nice ones though.

    Good luck and be safe.
    7 Billion people on the planet. They aint ALL gonna astronauts. Some will get hit by trains...

    Need GOOD SS pins to clean your brass? Try the new and improved model...



    And remember- 99.9% of the lawyers ruin it for the other .1%...

    Comment

    • #3
      KC001
      Junior Member
      • Jan 2016
      • 57

      Thanks for the reply
      I was debating on the Rainers 335 grs or the Berry's 300 or 325 gr. It seems there is not as much written down loading data for the 335 grs as the 300/325 grs. One load I have written down was 335 gr/ 28.0 grs 296/ WLP. I know how temperamental 296 can be. Is this a solid load?

      Comment

      • #4
        stilly
        I need a LIFE!!
        • Jul 2009
        • 10685

        Originally posted by KC001
        Thanks for the reply
        I was debating on the Rainers 335 grs or the Berry's 300 or 325 gr. It seems there is not as much written down loading data for the 335 grs as the 300/325 grs. One load I have written down was 335 gr/ 28.0 grs 296/ WLP. I know how temperamental 296 can be. Is this a solid load?
        H-110 is good stuff. I have a bottle of W296 but I have not used it. I have heard that it is the same basic stuff as H-110. (but it is not...)

        But it is so very close that it SHOULD be. (but it is not!)

        But for its application and what it does and its behaviors it mostly IS. (You mean mostly is NOT!).

        No I mean it IS, kinda. (No not really, but thank you).

        Anyways,
        I would certainly pick Rainiers over Berry's any day.

        And look for a 1LB bottle of some AA 1680. It is PINK and I have heard rave reviews of that in .50 AE.
        7 Billion people on the planet. They aint ALL gonna astronauts. Some will get hit by trains...

        Need GOOD SS pins to clean your brass? Try the new and improved model...



        And remember- 99.9% of the lawyers ruin it for the other .1%...

        Comment

        • #5
          KC001
          Junior Member
          • Jan 2016
          • 57

          Hello all,
          I recently acquired a set of RCBS .50 ae dies from a very nice gentleman here on calguns. I bought Berry's 300 gr bullets and am now ready to begin reloading. I have a few questions. I set up the re-sizing die per the RCBS instructions. Put the handle down, screw down die until touching, and then add an additional 1/4 turn to get the "pop". I measured the brass before and after using the re-sizer and the brass has grown 0.005". Is this normal or do I have my re-sizer set wrong. Also how many loads do you average out of one piece of brass and how often do you have to trim.
          Thanks

          Edit:
          It seems that I am having another problem. No matter how much crimp I put on the bullets, the bullets move out of the case about .020" when racked into the chamber. I am putting enough crimp to deform the outside plating of the bullet and it still will not stay still. Am I supposed to have deformation on the bullet when crimping? Does anyone have experience on how to correctly crimp for the .50AE?
          Last edited by KC001; 04-09-2016, 11:10 PM.

          Comment

          • #6
            stilly
            I need a LIFE!!
            • Jul 2009
            • 10685

            I have no experience at all for crimping for .50 AE but It is my understanding that as long as you give it a decent taper crimp that should be all you need to do. I do NOT know why your brass is growing, but I would not worry too much about that .005 (yet). What I would do though is to give it the plunk test. Build a dummy round, and see if it plunks and rests in the barrel chamber. Just remove the Deagle barrel and drop the round in. If it seats fine and goes all of the way in and plunks, you should be good to go. Decent taper crimp will remove the belling from the mouth. If you are making a restrictive band around your case mouth and deforming the bullet, you should consider backing off a bit. Also, keep in mind that unless you plan to rack your ammo, take it out and rack it a few more times, and then maybe rack it again and shoot it, there might be bullet setback. But if it happens just a little when the round is racked once, well, that could be nothing. But also please check that your projectiles are the proper diameter. The last time someone had a .380 with excessive setback his resizing die was not small enough or he had incorrect diameter bullets. I forgot, it could have been that his die was not resizing properly. Could be why you got such a great deal on that set... Check all of your measurements...

            I am not sure if you are supposed to trim brass for the 50 AE but it is a straight walled case so I would think NOT. However, compare the case length to that in the book and see if your case is shorter or longer and if it is longer, then maybe get a cheap trimmer and trim it down a skosh to get it into spec.

            I never had to trim my .44 mag and it has seen a lot.

            Good job scoring some RCBS. Remember, if you are using steel dies and your metal farts twice going up, back it out and use some lube. If it farts a third time, you might be losing that piece of brass and sending that die in to RCBS...
            Last edited by stilly; 04-10-2016, 3:06 AM.
            7 Billion people on the planet. They aint ALL gonna astronauts. Some will get hit by trains...

            Need GOOD SS pins to clean your brass? Try the new and improved model...



            And remember- 99.9% of the lawyers ruin it for the other .1%...

            Comment

            • #7
              Cheep
              Senior Member
              • Apr 2009
              • 1338

              You may be over expanding the case mouth, may have to reduce the diameter of your expander.
              Originally posted by NOMADCHRIS
              your asking a question about asking a question ??? just ask the damn question!!!

              Comment

              • #8
                KC001
                Junior Member
                • Jan 2016
                • 57

                That was my first thought also. I stopped using the expander and am now only using the resizing die. I still have bullet movement.

                Comment

                • #9
                  Cheep
                  Senior Member
                  • Apr 2009
                  • 1338

                  Ok, need more info...
                  Measure bullet diameter, case inside and outside diameter before and after resizing and post measurements.
                  Originally posted by NOMADCHRIS
                  your asking a question about asking a question ??? just ask the damn question!!!

                  Comment

                  • #10
                    KC001
                    Junior Member
                    • Jan 2016
                    • 57

                    I measured with a set of digital calibers.

                    I grabbed 10 random bullets:
                    High: 0.5005"
                    Average: 0.500"
                    Low: 0.04995"

                    Casings: Once Fired Hornady Brass
                    1st Casing:

                    Before resizing
                    Outside: 0.0527"
                    Inside: 0.501"
                    O.A.L: 1.280

                    After Resizing
                    Outside: 0.525
                    Inside: 0.499"
                    O.A.L: 1.287"

                    2nd Casing:
                    Before resizing
                    Outside: 0.0527"
                    Inside: 0.501"
                    O.A.L: 1.280

                    After Resizing
                    Outside: 0.525
                    Inside: 0.4985"
                    O.A.L: 1.287"

                    That doesn't seem like a lot of neck tension. I read an article that someone else was having the same problem and it ended up being their Resizer was out of spec. The interesting thing is today I pulled a Hornady casing. I dumped the powder, ran the new casing through the resizer, did not mouth, and set back the 300 grain XTP bullet in an attempt to rule out the Plated bullets. After I put a crimp on the jacketed bullet and sling shoted it into the chamber of my desert eagle (no powder, no primer), the bullet moved the same 0.020" as the Berry's bullets. I am now suspecting the dies are the culprit.
                    Last edited by KC001; 04-10-2016, 8:45 PM.

                    Comment

                    • #11
                      Cheep
                      Senior Member
                      • Apr 2009
                      • 1338

                      Looks like when the cases are sized down, you don't get enough interference fit.
                      Try a different set of dies if you have access to any and make sure the expander isn't stretching the case other than just a flair at the mouth.
                      Originally posted by NOMADCHRIS
                      your asking a question about asking a question ??? just ask the damn question!!!

                      Comment

                      • #12
                        Dooder
                        Senior Member
                        • Nov 2012
                        • 1514

                        300gr berry's and lee dies are gtg. that's the combo i'm using and it's great. i seat and crimp at the same time and no problems.

                        kc001
                        i run the lee 50ae dies and it's great, i seat and crimp in the same operation. interestingly i have lee 44mag dies and needed a set for 44spl. i still don't believe lee but the tech said that the particular set of 44mag dies i have won't work for 44spl. so i picked up a set of hornady 44mag/spl dies to try out. and i wish i got the lee set. they don't crimp for crap. i can apply so much crimp that the case buckles and the bullets still push down. in this scenario seating and crimping in seperate operations helps but the hornady still doesn't make as nice of a crimp as the lee does. the lee does a taper and when you lower the die will do a roll. the hornady just tapers then becomes a halfcrap roll and then buckles the case, and the bullet still pushes down haaha.
                        Last edited by Dooder; 04-11-2016, 12:46 PM.
                        Man, this place has gone bonkers.

                        Comment

                        • #13
                          tonyjr
                          Senior Member
                          • Nov 2015
                          • 1448

                          I prep case before it goes in to the machine [ de-prime , ream / clean pocket . tumble and re-prime ]
                          1st die expands case - 2nd is for powder - 3rd is for seating [ I thinks it is a hornady ] 4th is for setting OAL and 5th is for crimping [ if needed - I do from 25 ACP to 50 AE ] 6 TURRETS WITH DIESand one for tests , rifles etc .
                          About 85% LEE others are either given to me or missing piece sets off ebay .
                          I like the o-ring nuts better than the set screw ones .
                          I only use CCT primers .
                          I also think there is a difference between H11o and W296 .
                          Right now I only use jacketed bullets . I was given 5 coated bullets at a gun show - it looked like spray paint came out of barrel on 50 AE and 44 mag - gave the rest away .
                          I have not found anyone at range that is using plated ones - till then and I can look at the gas piston - I won't be using them either .
                          more info here

                          life member - CRPA and NRA
                          All ways listen - after you can say I new that

                          Comment

                          • #14
                            KC001
                            Junior Member
                            • Jan 2016
                            • 57

                            I talked to customer support from RCBS. They asked me to send my dies in so they can see if there is a defect. We'll see what happens.

                            Dooder: Do you know how much crimp you use? My problem is I put enough crimp on the bullets to deform the plating and I still had the bullets move out of the casing 0.020" when cycled by the slide. Same effect with the jacketed XTPs.

                            Tonyjr: I have read that Berry's seems to be the "strongest" plated bullets out right now. I have shot over a 1,000 .44 mag 240gr plated bullets though my desert eagle with good success. Originally I thought the plated bullets were the reason the bullets had could move in the case but I was having the same problem with the jacketed XTPs. If I get my dies back from RCBS and they say they can't see a problem, I am going to buy a set of lee dies and see if the that corrects it.
                            Last edited by KC001; 04-15-2016, 9:40 AM.

                            Comment

                            • #15
                              tonyjr
                              Senior Member
                              • Nov 2015
                              • 1448

                              KC001 - Thanks .
                              I will wait until I see someone using plated bullets .
                              I was at the gun show in San Fransico last week . Only one guy was selling H110 powder and he said he had not heard anything good or bad about plated bullets . He suggested that I stay away from coated ones for another year .
                              I ended up putting the gas piston from the 50 AE in rock tumbler with walnut shell for about 2 hours to clean the coated stuff off .
                              The 44 cleaned up with Hoppes , brass brush and a little elbow grease . [ maybe the 50 was harder because of more powder / heat ]
                              If anyone shoots plated bullets at the range while I am there , I will look at the barrel and if they are willing , maybe the gas piston . They might be willing to trade a few cartridges [ don't get wrong idea - I would take them home and reload to my spec's . ]
                              They don't sell plated around here , but fishing - guns [ Dublin ] and Bass pro shop [ san jose ] said they might get some .
                              I did email berry's about buying 5 of each [ 50 , 44 and 357 ] - we don't have samples and only sell by box .
                              I would have to look where which companies dies are . I deprime clean and reprime off press . Lee sizer , powder die , then I think a rcbs for seating , then a Lee for OAL and a Lee for crimping .
                              I have not found a 4 die set [ carbide ] for the 50AE or 25 ACP . [ YET ]
                              I use a lee loadmaster and the 50 AE shells have to be hand placed . I do dip both the 50 and 44's in mica before sizing . I don't think many people even know about mica and even fewer use it . [ I get mine from Frankford arsenal - midway ]
                              life member - CRPA and NRA
                              All ways listen - after you can say I new that

                              Comment

                              Working...
                              UA-8071174-1