Unconfigured Ad Widget

Collapse

Which single stage

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • #16
    Pauliedad
    CGN/CGSSA Contributor - Lifetime
    CGN Contributor - Lifetime
    • Dec 2012
    • 2095

    I really appreciate all the insight here. Thank you.
    I think the ammo I'm making is actually really consistent but I'm looking for that last little bit if it's to be had.
    What got me thinking about this was the seating discrepancies I'm seeing.
    I realize that any variation in resizing could be just as much at fault so I see myself using the single stage for sizing and seating only.
    I'd still de cap on the Dillon and after resize, trim, debut, and clean, I'd prime on the Dillon, charge by hand then back to the single stage.

    I looked at those parts to support the existing shell plate better and was wondering if that was worth it. Hmmmm.

    Again, thanks for the ideas here.

    Comment

    • #17
      noylj
      Senior Member
      • Oct 2010
      • 713

      If loading for a pistol, COL variations are not going to effect group size out to 50 yards. Remember, you are probably shooting about 12 MOA, so any minute improvement by worrying about such things is buried under that 12 MOA group.
      Shell plate variation can be controlled by tightening the shell plate until there is slight drag or by always having a case in the sizing station; however, my tests in my guns show NO difference in accuracy if I segregate out the first couple of rounds and the last couple of rounds from the rest and choreographing has shown no real difference with a +/- 0.006" COL variation and hand-picking rounds of the same COL for either pistols out to 50 yards or rifles at 100 yards.
      If you measure your bullets, you may find most of your COL variation right there. If you check the meplat of the bullets, you might find most the COL variation right there. With JHPs and FPs, you can actually see differences from bullet to bullet—yet, those bullets are almost always more accurate than a FMJ-RN If you measure COL of factory rounds, you will probably find your COL variation is less.
      If you are loading sub-0.5 MOA rifle for long-range competition, and need to possibly trim 0.05 MOA off the group, you "might" be going in the right direction.
      One thing you can always do is test whether what you are concerned about actually makes any difference on target. Time behind the trigger is a lot more important than a slight COL variation.
      Gosh, if accuracy is your goal, throw out the Dillon and work each step in batch with a single-stage press.
      I would not even consider doing anything off my Dillon presses that isn't case prep—and most case prep operations in my rifles based on my tests are meaningless, except checking case length and trimming as needed for safety.
      This is not say you shouldn't load however makes you happy and you're safe (as confidence in your loads will subconsciously make you more accurate), but it sounds like you are sweating very small details and making life more complicated than any target could justify.
      I deprime when I inspect and sort cases before cleaning. I prefer to keep all dirty jobs out in the garage, and that includes spent-primer compound in my press.
      Last edited by noylj; 10-05-2015, 6:37 PM.

      Comment

      • #18
        TMB 1
        Calguns Addict
        • Dec 2012
        • 7153

        I use an old Rock Chucker from early 70s or older maybe. It has a tray that catches primers.
        sigpic

        Comment

        • #19
          TMB 1
          Calguns Addict
          • Dec 2012
          • 7153

          Best way to go priming, is with something like the Lee Auto Prime when using a single stage
          sigpic

          Comment

          • #20
            BigBronco also not a Cabinetguy
            Calguns Addict
            • Jul 2009
            • 7084

            After making my post recommending the Forster CO-Ax and reflecting on the fact I sold my older model. I bought the new one today at Reload in Anaheim
            "Life is a long song" Jethro Tull

            Comment

            • #21
              homelessdude
              CGN/CGSSA Contributor
              CGN Contributor
              • Aug 2013
              • 2148

              I reload .300 Sav, .308, 30-06, 300 wsm, 30-30, .223, .270, 7.62x39, on my rock chucker. I also load 9mm, 10mm, .40, .45 on my ammo master. All my stuff is RCBS excepy I have a Hornady electronic scale and i'm happy with all of it. When loading rifle ammo I like to seat the primers by hand with the RCBS primer. It is pretty fast and I like to seat them by feel. Case prep is the key and consistency.

              Comment

              • #22
                'ol shooter
                Veteran Member
                • Mar 2011
                • 4646

                Yeah, the old 'Chuckers do throw the primers around, but I don't de-cap with the press anymore, so I like it better than ever now.
                sigpic
                Bob B.
                (\__/)
                (='.'=)
                (")_(")

                Comment

                • #23
                  noylj
                  Senior Member
                  • Oct 2010
                  • 713

                  My RockChucker came with a plastic tray to catch spent primers. It caught about 60%.
                  For me, I just didn't like the feel of it and the floor covered in spent primers was irritating.
                  To each their own--that's one reason we get to have opinions.

                  Comment

                  • #24
                    fguffey
                    Senior Member
                    • Mar 2010
                    • 1408

                    Reminds me of R. lee and Federal primers.

                    Rock Chucker and catching primers. Gigs and gigs of space has been used on the topic. I have green plastic trays, I attach the trays to the press with green 3M electrical tape, before I found the green, I used black.

                    F. Guffey

                    Comment

                    • #25
                      jh4db536
                      Junior Member
                      • Dec 2012
                      • 77

                      I was going to buy a forster coax but I felt I liked the simplicity of the ultra mag. Bigboss2 is second choice or old 70s rock chucker. I was going to buy the bb2, but I got a deal on a unused mag.

                      The bigboss2 is pretty expensive for looking like a brighter green rockchucker with a redding badge. I thought it felt completely different, smoother, tighter and just way better build quality overall. I think you actually need to try the press before buying and deciding if a 200 to $300 single stage is worth that kind of dough.

                      I love it. This thing has great leverage and is super heavy duty, the ergonomics aren't as nice as the bigboss2 tho as you have to "reach in" to feed and remove bullets...it's a big press way overkill for what im using it for. Every linkage is fitted tight, zero slop, but it moves like a well oiled machine.

                      I feel like I have great control especially at the very end of the stroke. That last 10% (compound linkage kicks in) where I feel maximum control pushing the shoulder back, using a small base die, or seating a bullet. The hard stop point and camover is very defined and consistent. This feel is what won me over.

                      As for using shell holders, I'm using the redding comp holder set to get the correct headspace. I mean I bought this thing for precision right?

                      uploadfromtaptalk1444199339342.jpg
                      Last edited by jh4db536; 10-07-2015, 7:08 AM.

                      Comment

                      • #26
                        Pauliedad
                        CGN/CGSSA Contributor - Lifetime
                        CGN Contributor - Lifetime
                        • Dec 2012
                        • 2095

                        Originally posted by BigBronco
                        After making my post recommending the Forster CO-Ax and reflecting on the fact I sold my older model. I bought the new one today at Reload in Anaheim
                        So I'm down to three options.

                        1. Co Ax.
                        Questions. So you're limited to full length resizing? Yes?
                        What's the model number difference so I can fit the taller comp seating dies?

                        2. Big Boss 2.
                        Questions. Any down side?

                        3. Stop looking to buy more stuff.
                        As pointed out before, I may be getting sucked in to this pursuit of the last 1% of consistency. The ammo I turn out on the 650 is really consistent and I'm pretty happy. As a side note, let it be known I only press one case at a time when I'm going for consistent. Im limited to full length resizing and am wondering if I will even see an improvement if I start to tweak shoulders for the particular chamber.
                        I could see myself getting all set up, making some uber precise rounds and not seeing a bit of difference on paper. I shoot mostly 100 and 200 yards for paper but enjoy (and can be reliable)getting out to about 700 yards.

                        Comment

                        • #27
                          TMB 1
                          Calguns Addict
                          • Dec 2012
                          • 7153

                          Originally posted by fguffey
                          I have green plastic trays, I attach the trays to the press with green 3M electrical tape, before I found the green, I used black.

                          F. Guffey
                          I use a piece of baling wire to hook it on, easy to take off and dump.
                          sigpic

                          Comment

                          • #28
                            fguffey
                            Senior Member
                            • Mar 2010
                            • 1408

                            I use a piece of baling wire to hook it on, easy to take off and dump.
                            TMB 1, A clothes hanger also works, I use the tape to reduce the gap between the catcher and press in the middle by pulling the two sides against the press.. The green tape is the same color as the catcher. Doing something beats complaining.

                            F. Guffey

                            I was reading through some responses about the handle falling on some presses. I have an aluminum wedge that came with one of my RCBS presses. When used it kicks the top pf the press back like the old 'C' type presses.

                            Comment

                            • #29
                              milotrain
                              Veteran Member
                              • Apr 2011
                              • 4301

                              Redding T7
                              weg: That device is obsolete now. They replaced it with wizards.
                              frank: Wait a minute. There are more than one wizard? Is [are?] the wizard calibrated?

                              Comment

                              • #30
                                5akman
                                Member
                                • Jan 2013
                                • 179

                                Originally posted by milotrain
                                Redding T7
                                Wow, 7 pulls on the handle to get one completed cartridge? Nice press but I wouldn't think its going to be too fast.

                                Comment

                                Working...
                                UA-8071174-1