Unconfigured Ad Widget

Collapse

Venturing into reloading... help me build a beginner's kit :)

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • quadmx301
    Senior Member
    • Jul 2013
    • 1426

    Venturing into reloading... help me build a beginner's kit :)

    Hi guys,

    been wanting to reload for several years now, and just getting to the point of feeling like it's now a need. I have a few odd calibers that reloading just makes better sense for, and I love the thought of getting more accuracy out of each of my guns.

    I know there's a wealth of information out there, but I wanted to ask everyone what their thoughts are for a good beginner's setup. I've been looking at the Lee Precision Breech Lock challenger kit. Keeping in mind that I expect my quantities to stay fairly low, what kit would you guys recommend that I but, and additionally, what should I add/replace?

    Thanks a lot everyone. You've all been very helpful already!
    "The deadliest weapon in the world is a Marine and his rifle" - Gen John J. Pershing, February, 1918
  • #2
    pdoggeth
    Member
    • Mar 2014
    • 369

    The Lee breech lock kit is the one I started out with... and actually I still am using it! It's a very good kit and it will get most of your needs done especially if you're just starting.

    I did upgrade my powder dispenser though, because the Lee one, while probably suitable for most needs, is rather annoying in that it's very hard to read the metering stick. If you are reloading more than one caliber or more than one kind of powder, it will be very hard to get back to X position. Also, the powder dispenser leaks a lot.

    You'll probably also want to get a digital scale of some sort, as the balance beam one is rather slow in getting you the weight readings.

    Anything else to consider? Calipers, reloading tray, bullet puller.

    And some nitrile gloves!

    Comment

    • #3
      liber
      Senior Member
      • Dec 2014
      • 1868

      Oh no...not the dreaded question....

      This never ends well...
      sigpic
      --------- liber --------

      From my cold dead end mill...

      Comment

      • #4
        quadmx301
        Senior Member
        • Jul 2013
        • 1426

        Originally posted by liber
        Oh no...not the dreaded question....

        This never ends well...
        I know, I know I knew there would be someone who posted something like this!
        "The deadliest weapon in the world is a Marine and his rifle" - Gen John J. Pershing, February, 1918

        Comment

        • #5
          Divernhunter
          Calguns Addict
          • May 2010
          • 8753

          Not sure why you need nitrile gloves but ok I guess.
          I have tried them all but still come back to RCBS spray lube. Get a metal baking pan dump some brass in it,spray....shake it ...quick 2nd spray and start resizing. Put sized stuff in a container at the bench. When done dump them out into a large towel. Fold towel over the brass and rub back and forth.
          Now you can hand prime while watching TV. Also chamfer the necks. Of course you have already trimmed to length after sizing.

          "Personally" I am not a big fan of lee presses. I have 2 RCBS and one Hornady single stage presses as well as my Dillon 650. I batch process my brass so it take 30 seconds to change dies between steps. I usually do batches of 200-5000 so I do not do much changing. That way I always have brass ready to just charge with powder and seat the bullet.

          Before you do anything buy the Lyman #49 Reloading manual and read it. It will answer most of the questions you have.

          There is also a trick with a funnel for more accurate throws with a powder measure.

          If you are near me you can come by and I will help you get set up and started. If not then feel free to PM me and I will answer questions on the phone or PM's. Just remember it is your money and your choice.----Doug
          A 30cal will reach out and touch them. A 50cal will kick their butt.
          NRA Life Member, NRA certified RSO & Basic Pistol Instructor, Hunter, shooter, reloader
          SCI, Manteca Sportsmen Club, Coalinga Rifle Club, Escalon Sportsmans Club, Waterford Sportsman Club & NAHA Member, Madison Society member

          Comment

          • #6
            Bikertrash
            Senior Member
            • Feb 2011
            • 1079

            You're welcome to come check out my set-up. Try it out & see what you think. I have the Lee Classic Turret press and really like it.

            Comment

            • #7
              silas3d
              Member
              • Apr 2015
              • 257

              +1 for the Lee turret press. I've got one and it does a great job for the $. It's also really easy to set up too.

              Comment

              • #8
                slayer61
                Senior Member
                • Jun 2014
                • 1402

                The Lee classic turret gets another vote.
                I'm a reloading newb, but the kit includes literally everything you need to begin loading, except the caliber specific dies.

                I get out in the shop and will do several hundred rounds in an afternoon. Good luck with whatever you choose.
                ΜΟΛΩΝ ΛΑΒΕ
                Paul

                Confirmed Domestic Terrorist & NRA Member


                Bobby Sands

                Comment

                • #9
                  pdoggeth
                  Member
                  • Mar 2014
                  • 369

                  Originally posted by Divernhunter
                  Not sure why you need nitrile gloves but ok I guess.
                  Oh the gloves heh. I just got tired of accumulating much grime and dirt on my hands when reloading. Plus they're handy when when cleaning guns too.

                  Comment

                  • #10
                    Magilla26
                    Member
                    • Jun 2015
                    • 111

                    I started loading for my 45/70 in 1995 with a Lee Anniversary Kit and Lee dies. In the last 15 years I have added a RCBS Rockchucker press and many Redding die sets for 12 different calibers. I love the Lee priming tool, the powder measure and Lee factory crimp dies.

                    Comment

                    • #11
                      opos
                      In Memoriam
                      • Oct 2009
                      • 1597

                      Old duffer here...loading for a lifetime...never left using a single stage press...my current press is a Lee Classic Cast press with the quick change breech lock bushings..the classic cast Lee is heavier by far than the standard lee classic press..it's cast iron and not cast aluminum..the ram is much heavier and the whole press is capable of about anything you might want to do.

                      As to a kit...might do a bit of investigating into what you will need to add and what you don't want....many folks do not care for the lee scale or the powder measure...I'm sure they are fine but I have an RCBS 5-0-5 scale (older one)that I bought used for about $40 and it's really accurate and easy to use...I don't use a powder measure...I use lee dippers..dip to near the charge weight and use an RCBS trickler ($10 used) to get exact weights per charge...much of the stuff in the kit is kind of un needed...you can make loading blocks or buy them on Ebay for way less..Priming tools are available new and used all the time, etc...I'm too cheap to buy a kit and then start to customize it...and the press ... being red...does not care if the scale is green, etc.

                      There are some great you tube videos by Ammosmith.com on reloading...some of the best I've seen...also CowboyT that is on this board now and then has great videos on you tube..I think he uses Lee dies and shows how to set them up properly...some of the videos that are on you tube are suspect...having the kids playing with the powder while you sweep up the dog poop and get another beer is not a good way to go..some are entertaining but dangerous.

                      If you are going to shoot a thousand rounds of 223 and the same with pistol cartridges every week a single stage is not for you but if you plan moderate loading and shooting the single stage might work...

                      I load in "stages"...I have several thousand cases prepped and sitting..when it's time to load up a couple hundred handgun cartridges I can do that in a day or so...take each stage...do all the operations..move to the next stage

                      I like the single stage for "learning" as you get to see each phase and also get to inspect your work...I like to look the brass over at each stage..like to check primers and powder charging, etc as I go along...with a multiple stage press...when you are new...things might get by you like an upside down primer...no powder..double charge, etc..things I can experience but never have as yet.

                      If you load for rifles you probably will want to use a single stage for a while..It's more complex than loading for handguns...if I'm not mistaken you are the guy that likes M-1's and military rifles..a single stage might simplify things...and you can always keep the single stage if you move up to a turret, etc..handy for short runs and test loads...setting up a multiple stage press to run 20 or 30 rounds for a test is pretty time consuming as I understand it.

                      Just an old guy with lots of time and not too much need for high volume..whatever..get the manuals and read them...internet info can be fine but needs to be verified..there are some folks that never loaded a cartridge that are more than willing to share their "knowledge" and it might bite you.

                      Good luck and load safe.
                      Last edited by opos; 09-03-2015, 4:50 PM.
                      God and the Constitution give me my rights and actions...any other input is just blabbering.

                      Comment

                      • #12
                        M1NM
                        Calguns Addict
                        • Oct 2011
                        • 7966

                        Depends on caliber. Up to .223 you'll be fine with the Lee. For bigger cartridges you'll appreciate the added leverage of an RCBS Rockchucker. Rifles aren't anymore difficult to load for than pistol.

                        Comment

                        • #13
                          rdtompki
                          Senior Member
                          • Mar 2014
                          • 773

                          Originally posted by pdoggeth
                          Oh the gloves heh. I just got tired of accumulating much grime and dirt on my hands when reloading. Plus they're handy when when cleaning guns too.
                          Once you're working with clean/tumbled brass where does the grime come from? I suppose gloves would make sense with lead bullets, but coated lead, plated, FMJ, etc. are very clean.

                          Comment

                          • #14
                            opos
                            In Memoriam
                            • Oct 2009
                            • 1597

                            Originally posted by M1NM
                            Depends on caliber. Up to .223 you'll be fine with the Lee. For bigger cartridges you'll appreciate the added leverage of an RCBS Rockchucker. Rifles aren't anymore difficult to load for than pistol.
                            Maybe a "problem" with the Lee standard classic press but I regularly load 06, 7mm, 25-06, 8mm and 7mm mag on the classic cast..it's every bit as strong and convenient as the Rock Chucker (and nothing at all wrong with RCBS..great press for but more money..and may not be made in the U.S...not sure about that).

                            As to difficulty of loading it's probably a matter of personal preference..if loading for an AR and spewing out hundreds or thousands of rounds on a weekend maybe so...I think for a precision loader with larger cases that the steps and the attention to detail is probably more involved with a rifle than a handgun round. I load a ton of 38, 357, 44, 45acp, 45 Colt and they are just a simple repetitive process ... loading for the 25/06, 7mm (7x57 and 7mm Magnum, etc), 8mm, where neck sizing and then occasional full length sizing, case trimming (I've never trimmed any handgun rounds at all), neck push back to tailor the cartridge for the rifle, annealing (I've never annealed any handgun brass), etc is a much more involved thing that punching out 38 specials.

                            The O/P said he had "odd calibers" and if there is any case forming, etc to be done it's a far more complicated situation and probably needs a strong single stage press. Again...all in the perception and the specific case. I'd hate to try and process brass for the 06-Ackley that I shot for many years on anything but a solid single stage press with several steps involved to just get usable brass.
                            Last edited by opos; 09-03-2015, 8:09 PM.
                            God and the Constitution give me my rights and actions...any other input is just blabbering.

                            Comment

                            • #15
                              chknlyps2
                              Senior Member
                              • Apr 2011
                              • 2191

                              Originally posted by quadmx301
                              Hi guys,

                              been wanting to reload for several years now, and just getting to the point of feeling like it's now a need. I have a few odd calibers that reloading just makes better sense for, and I love the thought of getting more accuracy out of each of my guns.

                              I know there's a wealth of information out there, but I wanted to ask everyone what their thoughts are for a good beginner's setup. I've been looking at the Lee Precision Breech Lock challenger kit. Keeping in mind that I expect my quantities to stay fairly low, what kit would you guys recommend that I but, and additionally, what should I add/replace?

                              Thanks a lot everyone. You've all been very helpful already!
                              I have never used the Breach Lock press, many have said they like it. The Lee scale is not worth it's weight in scrap metal. You can watch the market place here or keep an eye on ebay for a Lyman, RCBS or Ohaus beam scale and find a good deal.

                              I have a couple of the Lee hand priming tools and I like them, I have used Lyman and RCBS and like the Lee better. The Lee Perfect Powder Measure works pretty good for being plastic and inexpensive, it meters stick powder better than my metal Hornady or RCBS powder measures.

                              Lee dies work but are not always the best choice, don't use them for your K31... they will resize way under spec and work your brass way to much. The Redding or Hornady K31 specific dies cost more but are a much better choice.
                              Wanted: Spent Berdan primed Yugo 7.62x39 & 7.5x55 GP11 Swiss brass

                              Comment

                              Working...
                              UA-8071174-1