Unconfigured Ad Widget

Collapse

Random questions :)

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • AreWeFree
    Veteran Member
    • Jan 2013
    • 4558

    Random questions :)

    Hey All,

    I'm still a newb, currently loading 9mm to build experience.

    Anyway, I've got a few dumb questions, mostly just for curiosity, hoping you all can help steer me in the right direction.

    1. What case gauge's do you all like? I took out my LE Wilson gauge today and it has rust on the inside and outside where it was touching paper... kinda bummed since the inside is hard to clean! Definitely wont store in the box anymore, threw that away, but also don't want to buy more of their gauges...

    2. About 15 - 20% of my loaded ammo doesn't drop free from the case gauge, why is that?

    I'm running 1.133 COAL, 124gr Berry's plated, no crimp, same headstamp from same lot.

    3. What's the height of your workbench? My setup sucks, I need to build something.

    4. I'm loading in batches, is it ok to prime several hundred pieces of brass and leave them in a container for extended periods of time until I'm ready to load them?

    5. Are the quick change die bushings worth the expense, or is it better to just upgrade the lock rings, or neither? I have RCBS and Lee dies on single stage.

    6. I'm handling the brass a lot during processing, for extended storage are there any tricks to minimize corrosion? I'm tumbling with Lyman Tufnut, then decap/resize, and store until ready to load.

    7. Is there a special way I should store my balance beam scale? RCBS 505, I just slide the heavy weight to the left so the beam is stationary and put it in my reloading cabinet.

    8. Any recommended lube for the press ram? I put a little gun oil on it and it got pretty rough.. then wiped it off and used Brownells Action Lube (moly grease I think) and it smoothed out. Moly grease ok?

    9. Do you recommend die maintenance? I took my dies apart and cleaned with rubbing alcohol when I first got them, unsure if I should be routinely doing that (every few thousand rounds?)

    10. I recently tested several powder charges for Power Pistol in 9mm, I think the charge was too light. Action cycled just fine even on the weakest minimum load, but the side of the ejected cases were black like the case wasn't sealing well enough in the chamber.

    Is that accurate of what is occurring, and the charge should be increased?

    I was testing Power Pistol for 9mm 124gr plated RN at 1.135 COAL, loaded a few at 4.8, 5.0, 5.2, 5.5, all spent cases looked identical.
    After reviewing other sources, looks like I should have been starting at 5.6 - 6. No signs of excess pressure, so now I'm loading 5.9 - 6.0

    11. I have a fair amount of junk 12ga shotgun hulls, all RIO or PMC, I don't think anyone would want them to reload. Just trash them or can they be recycled?

    12. For commercial loaders, do they generate enough heat when sizing/etc that they have to cool their dies to keep everything uniform (watercoooled dies?)?


    I'm sure these are annoying questions, sorry, but thanks for any help!
    I spent wayyy too much time today sweating in my garage resizing thousands of 9mm/.380/40sw, then sorting an entire tub of 9mm and priming 200 pieces of brass... all I could do is think up questions to ask you all!
  • #2
    stilly
    I need a LIFE!!
    • Jul 2009
    • 10685

    1. Barrel of the guns are my case gauge. PLUNK test them. Buying a case guage for 9mm or .45? Yawn waste of money. Dillon seems to make a nice one that does not rust like the others. Bronco showed me his once, then FP showed me his and I showed FP and Bronco mine...

    2. Stop eating honey biscuits and they will not stick. Are you loading lead? Apparently 9mm is NOT a standardized caliber therefore projectiles can be .355-.358 or bigger. If you are loading lead and they are larger they could stick a bit. but are they HARD stick or do they just have a little friction going in and out? Try it with the barrel and see if those work. Or it could be all of that rust you have...

    3. Mine is about 4' off the floor. We just built a work bench adn then I made it my reloading bench. I have a barstool that I can sit on and work well at it though.

    4. Yes. That is a good way to batch things up. LoL. That is ideal, batch jobs are how single stage loaders work. Just keep them away from excessive humidity and moisture.

    5. Quick change work great if you change dies a lot, else who cares. Take your time and screw/unscrew.

    6. Can't help you there. I am a wet processor.

    7. My 5-0-5 has taken a back seat to my Gemini Pro 20G digital scale and it just sits with who knows what weight on it in the back gathering dust.

    8. OIL. Light oil, maybe a drop or two. Grease might work, but I think it might be a bit heavy. But I am no expert, I THOUGHT I was told to put a drop or two of oil on the ram every now and then and wipe it off after xx rounds and re oil it just for fun, but it is a Lee Classic Turret and it works very well but I have put white grease on the turret portion in the past.

    9. 6 one way half a dozen the other way. Yes and no. If you are one of those people, by all means, go for it but I rarely clean my dies but then again, I wet process so My brass is always nice and clean with no primers inside when I put it on the press. (usually)

    10. Apparently if your powder does not build up pressure fast enough it will not expand the case properly and thus degas itself down one side and leave a cone of scorched case for you. I THINK that could mean that the powder was too light or that the case was maybe not crimped enough- BUT GET A SECOND OPINION ON THE CRIMP. Tapered crimp for 9mm does not need to be heavy, just enough to hold the bullet in place.

    11. We do have a pay it forward thread around here that you could offer it to someone for free or whatever, I see free being used and maybe a small amount for shipping...

    12. I do not think so. I have seen several videos with CAMDEX machines and there was no water cooling that I saw. But I have not seen everything so who knows. I do not think that the action really moves that fast though to generate excessive heat.

    Your questions certainly are annoying. I think I will invite FP over to your house. Then you can enjoy sweating while he puts his junk in your trunk and everytime you come up with another question he will lick his fingers and give you a wet willy...



    Oh moded moded! scratch scratch!

    Last edited by stilly; 06-24-2015, 2:52 AM.
    7 Billion people on the planet. They aint ALL gonna astronauts. Some will get hit by trains...

    Need GOOD SS pins to clean your brass? Try the new and improved model...



    And remember- 99.9% of the lawyers ruin it for the other .1%...

    Comment

    • #3
      AreWeFree
      Veteran Member
      • Jan 2013
      • 4558

      Originally posted by stilly
      Your questions certainly are annoying. I think I will invite FP over to your house. Then you can enjoy sweating while he puts his junk in your trunk and everytime you come up with another question he will lick his fingers and give you a wet willy...



      Oh moded moded! scratch scratch!


      Ohhh, umm, actually I just remembered I need to go sell my house and move out of country... yeah yeah, I think I'm getting sick too, , I'll survive as long as you stay away forever

      Comment

      • #4
        BigBronco also not a Cabinetguy
        Calguns Addict
        • Jul 2009
        • 7084

        1, I like the Dillon Case gauges. They are stainless steel and reasonably priced. I have most other brands also that are not stainless and they all rust.

        2, No crimp may be your answer. I use me case gauge to set the crimp. lightly increase the crimp until they pass the case gauge test.

        3, Not sure, I will be setting up a new bench shortly at new digs.

        4, Absolutely fine. The boxes primers come in are not air tight so you should be fine if stored garage lets say.

        5, Quick change bushings are good time savers. Note I did not say great time savers. Once you set the lock ring on your dies and remove them from the press they will go back in to the press and stop in the same position with no adjustment needed. The quick change bushings only save you the time to thread the die in to the press. Keep in mind the locking the ring when the die is set will make removal the first time a bit tough. Hence I recommend rings that have flats for wrenches.

        6, Nickle plated brass has it's place. A quick tumble in car wax will apply a light coat of protectant.

        7, I would cover it with a small towel if you are not putting it back in the box. Dust in the pivot bearings is not the best thing. One more reason I recommend the 10-10 scale.

        8, Any good lube is fine I use Hornady one shot cleaner / lube.

        9, Clean and lube them to prevent rust. Been loading for 30 years. I need to do that some day.

        10, Yup, there was not enough pressure to seal the chamber. Increase your charge. Remember if it gets on the side of the cases it is getting in your barrel chamber as well.

        11, I personally do not use them, I do know some guys who do, The three gun shooters loose a lot of cases since they can not stop to pick them up. They prefer cases that they can load one time and not worry about recovery. However they get all the free ones they can pick up at trap ranges I doubt they would buy them.

        12, Not going to be able to answer this one.
        Last edited by BigBronco; 06-24-2015, 12:13 PM.
        "Life is a long song" Jethro Tull

        Comment

        • #5
          J-cat
          Calguns Addict
          • May 2005
          • 6626

          1. I don't. If you set up your dies correctly and use the right components the resulting ammo will feed and fire reliably.

          2. That's because your case gauge is tighter in diameter than your ammo. There could be a number of reasons: your brass thickness, bullet diameter, die adjustment, tool dimensions, etc.

          3. The height of my bench is not relevant. Build your bench to where you have good leverage.

          4. Yes

          5. No. I prefer threads to bayonets for alignment reasons.

          6. Use gloves.

          7. No.

          8. Mobil-1 50 weight oil

          9. Clean them as necessary.

          10. PP likes to run hot. The nice thing about PP is that you can't overload it in the 9mm. If you want mild, use another powder.

          11. Make art out of them. I would screw them base first into your front door.

          12. I'm not a commercial reloader but it will be interesting to see people offer opinions based on their inexperienced assumptions.

          Comment

          • #6
            slopoke
            Senior Member
            • Jan 2010
            • 509

            One thing to consider, the term "crimp" in this situation is just for removing the bellmouth you gave the case. It's not to hold the bullet in the case. So if you did not remove the bellmouth, thats your problem.

            Comment

            • #7
              AreWeFree
              Veteran Member
              • Jan 2013
              • 4558

              Thanks guys, really good info in all of your posts, I appreciate it very much.

              Just a quick follow up on my case gauge question for my current load.

              I'm using a Lee die set, so to increase the taper crimp I need to seat the bullet further?


              Also, big thanks for the tip on covering my scale, I had no idea the bearing surfaces could get gunked up so easily.

              I think I'll find the box it came in, cut the top off, and use that for a cover.

              Comment

              • #8
                BigBronco also not a Cabinetguy
                Calguns Addict
                • Jul 2009
                • 7084

                Originally posted by AreWeFree
                I'm using a Lee die set, so to increase the taper crimp I need to seat the bullet further?
                Negative. The best way is to seat then crimp in two different steps. Once you set the OAL (bullet depth) Back off the seating stem and adjust the crimp by its self.

                If doing it in one pass. this is the method.

                1. Set seating depth.
                2. Back off seating stem adjustment and then set the crimp.
                3. Once the crimp is set reset the seating stem by running it down until it comes in firm contact with the bullet. This then should be the final setting. However the OAL may need minor adjusting.

                Should the case wall buckle you have too much cripm as the bullet is being presses home.
                "Life is a long song" Jethro Tull

                Comment

                • #9
                  AreWeFree
                  Veteran Member
                  • Jan 2013
                  • 4558

                  Well I feel foolish, I just re-read the die instructions and saw how to adjust that in the seating die, although your advice was better than Lee's instructions.

                  I'll add a reloading class to my to do list, you guys have all the good tricks.

                  Comment

                  • #10
                    slopoke
                    Senior Member
                    • Jan 2010
                    • 509

                    I seat and crimp in two different stations. My brass is mixed headstamps and are not uniform in length. If I use the crimp feature of the seating die, meaning seating and crimping on the same station, the crimp on one case may be too much or too little on another, because of different case lengths. Once I went to seating and crimping on two different stations, my chambering issues went away.

                    Comment

                    • #11
                      AreWeFree
                      Veteran Member
                      • Jan 2013
                      • 4558

                      Honestly I wasn't adding a crimp, at least not intentionally. I set my seating die per instructions, 3 turns out from touching shell holder, then adjusted seating depth until I had my COAL.

                      Berry's plated bullets appear to be on the large size, and they bulge the case mouth when seating more than what I expanded to. Also I understand the Lee FCD sizes the case and read many people saying don't bother using this, saying it works the brass unnecessarily and the spec is too tight.

                      These Lee dies were the first I bought and I really don't like the configuration, although they seem to be working wonderfully.

                      Just to clarify, all of my loaded cartridges so far appear to be in spec, a small amount stick in the case gauge but sit flush and don't need but a gentle tap to remove.

                      I think you guys nailed it before, variance of case length and not applying enough taper crimp.

                      Comment

                      • #12
                        stilly
                        I need a LIFE!!
                        • Jul 2009
                        • 10685

                        Of course we did. We are the reloading experts of the internet. The ONE group of people that you can call upon to solve all of your reloading needs. We are Kelly's Heroes of the red, blue and green machines.

                        More faster than a Dillon 1290 XF (coming out next year), able to leap a primer brick wall in a single bound, more powerful than Joe Biden giving out shotgun advice, and with the addition of the FP angle, more sexy than J-Lo and Nicki Minaj combined with a side of Britney Spears tangled with Megan Fox...

                        Look, up in Skype! It's word, it's vain, yes it's the CG reloading forum guyz...


                        7 Billion people on the planet. They aint ALL gonna astronauts. Some will get hit by trains...

                        Need GOOD SS pins to clean your brass? Try the new and improved model...



                        And remember- 99.9% of the lawyers ruin it for the other .1%...

                        Comment

                        • #13
                          rm1911
                          Veteran Member
                          • Jan 2013
                          • 4073

                          J-cat,

                          Could you clarify the power pistol statement, about not being able to overload it? I'm not disagreeing or debating or arguing or anything. Just curious about it. That's all. I love power pistol. My 9mm powder had always been AA #5 but alas it's made of unobtanium. Found PP and really really like it. I've found 5.5-6 ideal for 115-124's. Great accuracy and reliability. I've no need to go hotter. Just wondering, that's all.
                          NRA Life Member since 1990

                          They're not liberals, they're leftists. Please don't use the former for the latter. Liberals are Locke, Jefferson, Burke, Hayek. Leftists are progressives, Prussian state-socialists, fascists. Liberals stand against the state and unequivocally support liberty. Leftists support state tyranny.

                          Comment

                          • #14
                            J-cat
                            Calguns Addict
                            • May 2005
                            • 6626

                            You can't stuff enough PP in a 9mm case to KB a 9mm. The powder is prolly the most forgiving in terms of pressure. If you look up Clark Manguson's work with PP and various 9mm platforms you'll fully embrace the powder. 6grs under a 124 is an established accuracy load. It has a lot of flash and blast making you think it is more powerful than it really is. That's why people go down in weight which is a mistake. 124/PP likes 6grs plus not minus.

                            Comment

                            • #15
                              AreWeFree
                              Veteran Member
                              • Jan 2013
                              • 4558

                              ^I've seen various load data, but being a newb I don't want to take anything for granted.

                              Manufacturer lists:
                              115gr GDHP 1.124 Minimum OAL, 6.7gr MAX 1212fps
                              147gr GHDP 1.130 Minimum OAL, 5.0gr MAX 975fps


                              (Gee thanks Alliant for the crap data on your powder, useless jerks... )

                              6gr leaves a fair amount of case left for seating and with 124gr plated bullet at 1.133 I'm on the boundary of a compressed load.

                              I'm guessing with a little higher charge and lower seating depth I'd be nearing dangerous pressures.

                              Comment

                              Working...
                              UA-8071174-1