Unconfigured Ad Widget

Collapse

Dies scratching cases

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • mclakers
    Junior Member
    • Mar 2013
    • 56

    Dies scratching cases

    Hello guys,

    I started reloading 45 acp this past week with lee carbide dies, and I've noticed the bullet seating die scratches some of my cases. Ive cleaned and lubed the dies a couple of times with the same result, adjusted the flare on the powder through die, lubed the cases with ltitle or no improvement. I reload 223, 9mm with lee dies and have never had a problem. I'm beginning to think the die is defective. HELP!

    Some pictures are attached.

    Thanks in advance
    Attached Files
    Last edited by mclakers; 04-13-2015, 11:46 PM.
  • #2
    Fordtrucks
    Member
    • May 2008
    • 410

    The Lee has a carbide sizer in the lower part of the factory crimp die. That's prolly what causing this. Check to make sure it's not rough.
    How deep are the scratches? Can u feel the valleys with ur fingers in the location of the scratches?
    If it's just a visual thing, were the reflection of the light makes it visible but not noticeable by feel then I would worry, it's not causeing any harm to the cases.

    If the scratches "are" deep, then u can always just roll crimp with the normal seating die while Lee sends a replacement.
    U might even be able to just polish the carbide ring with a dremel also. But that shouldn't really be necessary.

    Comment

    • #3
      mclakers
      Junior Member
      • Mar 2013
      • 56

      Originally posted by Fordtrucks
      The Lee has a carbide sizer in the lower part of the factory crimp die. That's prolly what causing this. Check to make sure it's not rough.
      How deep are the scratches? Can u feel the valleys with ur fingers in the location of the scratches?
      If it's just a visual thing, were the reflection of the light makes it visible but not noticeable by feel then I would worry, it's not causeing any harm to the cases.

      If the scratches "are" deep, then u can always just roll crimp with the normal seating die while Lee sends a replacement.
      U might even be able to just polish the carbide ring with a dremel also. But that shouldn't really be necessary.

      The bullet seating die is the one scratching the cases, on some cases the scratch is small and on some is deap ( you can feel the groves) Like on the 3rd picture.

      - the interior of the die looks normal, but lots of brass is being scraped off.

      -yes I can feel the valleys, and you can see the scrapping without the light reflection.

      Comment

      • #4
        stilly
        I need a LIFE!!
        • Jul 2009
        • 10685

        that sounds very odd. Have you contacted Lee yet? Is this a new purchase? Send your dies in to Lee and tell them what is going on. They should take care of you.

        The seating die typically does not grab the case though, well, it forces it closed for the crimp, but that is towards the top.

        You have your die adjusted properly?

        Also, BEFORE you put the brass in the die, will you roll your brass and see that it rolls smoothly? Maybe you got a batch of glocked brass and it needs some extra tlc.
        7 Billion people on the planet. They aint ALL gonna astronauts. Some will get hit by trains...

        Need GOOD SS pins to clean your brass? Try the new and improved model...



        And remember- 99.9% of the lawyers ruin it for the other .1%...

        Comment

        • #5
          Cheep
          Senior Member
          • Apr 2009
          • 1339

          That looks like it's scratched on one side only. If that's what is happening, i'd look into why it's not centered in the die.
          Originally posted by NOMADCHRIS
          your asking a question about asking a question ??? just ask the damn question!!!

          Comment

          • #6
            fguffey
            Senior Member
            • Mar 2010
            • 1408

            I have to agree with cheap, the case is not centered in the shell holder.

            F. Guffey

            Comment

            • #7
              stilly
              I need a LIFE!!
              • Jul 2009
              • 10685

              FWIW, My cases are not always centered either, but when the bullet tip hits the entry, it slides the case into alignment and then seats and crimps. No issues or worries.

              Are you suggesting that maybe a burr is on the shell holder preventing the case from seating all of the way in? Wouldn't that also mess up the flaring portion too?
              The only issues I have had were with this latest batch of HP that I have, I have to slow down or else their standard base makes them seat at an angle and then upon correcting it, half of the side of the case gets destroyed.

              I hope OP is not using any Smart Reloader brand presses...
              Last edited by stilly; 04-14-2015, 12:02 PM.
              7 Billion people on the planet. They aint ALL gonna astronauts. Some will get hit by trains...

              Need GOOD SS pins to clean your brass? Try the new and improved model...



              And remember- 99.9% of the lawyers ruin it for the other .1%...

              Comment

              • #8
                chknlyps2
                Senior Member
                • Apr 2011
                • 2191

                wow, 2nd pic in your hand looks pretty deep. I would put a fresh case in the shell holder and raise the ram up and down. Before you remove the case look where the scratches are and mark that side of the die with a sharpie. Take the die out and inspect that side for rough marks, might even be able to feel the roughness with a dry q-tip if the burs tug on the fibers. Possibly polish with fine emery wrapped on a pencil or something.

                What press are you using? Not centered might be caused if it is a turret and it is not indexed correctly in that position. If so put that die in a different hole and see what happens.
                Wanted: Spent Berdan primed Yugo 7.62x39 & 7.5x55 GP11 Swiss brass

                Comment

                • #9
                  mclakers
                  Junior Member
                  • Mar 2013
                  • 56

                  Originally posted by chknlyps2
                  wow, 2nd pic in your hand looks pretty deep. I would put a fresh case in the shell holder and raise the ram up and down. Before you remove the case look where the scratches are and mark that side of the die with a sharpie. Take the die out and inspect that side for rough marks, might even be able to feel the roughness with a dry q-tip if the burs tug on the fibers. Possibly polish with fine emery wrapped on a pencil or something.

                  What press are you using? Not centered might be caused if it is a turret and it is not indexed correctly in that position. If so put that die in a different hole and see what happens.
                  I am using a lee classic turret press. After taking your advice and moving the die to another location i got the same results, scratches and scrapes. I also turned the die another 1/2 turn and the scrape moved to the new location. Die is defective.

                  Thanks for the help

                  Comment

                  • #10
                    stilly
                    I need a LIFE!!
                    • Jul 2009
                    • 10685

                    Originally posted by chknlyps2
                    wow, 2nd pic in your hand looks pretty deep. I would put a fresh case in the shell holder and raise the ram up and down. Before you remove the case look where the scratches are and mark that side of the die with a sharpie. Take the die out and inspect that side for rough marks, might even be able to feel the roughness with a dry q-tip if the burs tug on the fibers. Possibly polish with fine emery wrapped on a pencil or something.

                    What press are you using? Not centered might be caused if it is a turret and it is not indexed correctly in that position. If so put that die in a different hole and see what happens.
                    0o0o0 yeah I forgot about that. The Lee turret typically is off and needs to be adjusted. But it looks like OP figured it out.

                    Bad die. No more brass!
                    7 Billion people on the planet. They aint ALL gonna astronauts. Some will get hit by trains...

                    Need GOOD SS pins to clean your brass? Try the new and improved model...



                    And remember- 99.9% of the lawyers ruin it for the other .1%...

                    Comment

                    Working...
                    UA-8071174-1