Unconfigured Ad Widget

Collapse

ar lower problem (pics added)

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • steelrain82
    Veteran Member
    • Jul 2009
    • 3683

    ar lower problem (pics added)

    So tonight I went shooting and test out my newly complete lower. Now I would like to say she worked flawlessly but I cant. So after I fired a round the bolt cycles and chambers a new round. The trigger doesnt reset until I put the selector on safe. After that I can fire the next round. What is wrong?

    I took the lower off and hand worked the hammer pretending I was firing. If I keep holding back the trigger, after the hammer goes forward and then reset the hammer the trigger is "locked" until I put it on safe. And then it reset and once I put it on fire it I can then pull tye trigger to release the hammer again. I hope this makes sense
    Last edited by steelrain82; 05-07-2013, 10:23 PM.
  • #2
    DFence
    • Feb 2012
    • 1368

    Your safety selector is in wrong.

    When you install it, it needs to be in the "fire" position when you put in the the safety selector detent and spring and install the grip.
    Its not paranoid.....its prepared.

    NRA Certified Pistol/Rifle/Shotgun/PPIH/PPOH Instructor | NRA Certified RSO | NRA Life Member | GSSF Life Time Member | Surefire Low Light Instructor | Glock Certified Armorer | Utah CCW Instructor | Nevada CCW Instructor

    Comment

    • #3
      DFence
      • Feb 2012
      • 1368

      Or at least that's what it sounds like. Run some safety checks before firing the weapon again.
      Its not paranoid.....its prepared.

      NRA Certified Pistol/Rifle/Shotgun/PPIH/PPOH Instructor | NRA Certified RSO | NRA Life Member | GSSF Life Time Member | Surefire Low Light Instructor | Glock Certified Armorer | Utah CCW Instructor | Nevada CCW Instructor

      Comment

      • #4
        steelrain82
        Veteran Member
        • Jul 2009
        • 3683

        ok i gave what you said a shot and i get the same result. if i continue to hold the trigger it still doesnt reset and i have to de-select the safety for it to reset then put in on fire to fire.

        Comment

        • #5
          DFence
          • Feb 2012
          • 1368

          Is your disconnector spring installed and installed correctly? Also, is this built from a 80% lower by chance?
          Its not paranoid.....its prepared.

          NRA Certified Pistol/Rifle/Shotgun/PPIH/PPOH Instructor | NRA Certified RSO | NRA Life Member | GSSF Life Time Member | Surefire Low Light Instructor | Glock Certified Armorer | Utah CCW Instructor | Nevada CCW Instructor

          Comment

          • #6
            killmime1234
            Senior Member
            • Mar 2009
            • 1536

            I've seen this before with poorly manufactured disconnectors. Try a little bit of grease (white lithium works) on the surface of the disconnector that catches the hammer. It could be a dimensional issue also, but if it's just a rough enough cut on the disconnector, some grease should do the trick.

            Comment

            • #7
              tanakasan
              Senior Member
              • Oct 2011
              • 1638

              Originally posted by DFence
              Is your disconnector spring installed and installed correctly? Also, is this built from a 80% lower by chance?
              ^^This

              Make sure the spring is installed large end in the trigger. And hopefully if its an 80%, its machined to spec. Sorry to hear of a wasted range trip! Did you not function check the FCG and safety before going?

              Robert
              WTB/WTT

              Comment

              • #8
                dieselpower
                Banned
                • Jan 2009
                • 11471

                Normally when the disconnector spring is upside down, the fat end of the spring locks the whole spring into the trigger troth, thereby allowing the disconnector to stay out of the way from snagging, and allowing double or triple fire.

                The safety holds the trigger troth in place, if you must reset the safety to reset the trigger, I think your trigger spring is in wrong. When you set the safety, you reposition the trigger.

                Best thing to do is start over. Pull the pins and go again, making sure you follow the proper spring installation directions.

                Use the youtube videos. watch several and make sure you match up all the directions correctly.

                Comment

                • #9
                  SouperMan
                  Senior Member
                  • Jan 2012
                  • 1463

                  Here is a good YouTube video that shows the function of the trigger and disconnect:

                  Comment

                  • #10
                    Rider1k
                    Senior Member
                    • Jul 2012
                    • 1939

                    Check your spring. then check it again. It is a one way spring. A little larger on one side then the other. I has to be installed correctly or this will happen. Take it out and flip it over. Prob solved. Hopefully. This happened to me one time and it killed me for about a hour before I had to slap myself in the head.

                    Comment

                    • #11
                      steelrain82
                      Veteran Member
                      • Jul 2009
                      • 3683

                      Yeah I checked it and its the disconnector spring. The last coil of the spring is larger than the previous ones. I would be able to push the whole spring through the last coil if it was possible. Called stag and they are sending me a new one. Hope that solves my problem.

                      Comment

                      • #12
                        SixPointEight
                        Veteran Member
                        • May 2009
                        • 3788

                        The last coil is SUPPOSED to be larger. That's the side that goes into the trigger...

                        Comment

                        • #13
                          -hanko
                          CGN/CGSSA Contributor
                          CGN Contributor
                          • Jul 2002
                          • 14174

                          Originally posted by SixPointEight
                          The last coil is SUPPOSED to be larger. That's the side that goes into the trigger...
                          /Thread
                          True wealth is time. Time to enjoy life.

                          Life's journey is not to arrive safely in a well preserved body, but rather to slide in sideways, totally worn out, shouting "holy schit...what a ride"!!

                          Heaven goes by favor. If it went by merit, you would stay out and your dog would go in. Mark Twain

                          A man's soul can be judged by the way he treats his dog. Charles Doran

                          Comment

                          • #14
                            steelrain82
                            Veteran Member
                            • Jul 2009
                            • 3683

                            I'll post a pic later its a huge mess up on the coil

                            Comment

                            • #15
                              steelrain82
                              Veteran Member
                              • Jul 2009
                              • 3683

                              Ok, so I took apart the trigger and hammer and reinstalled everything. I even got two new disconnector springs. But I get the same issue. During a somewhat limited function check. By holding back the trigger after I reset the hammer it will not fire until I flick the safety back on and then return it to fire.

                              Which way is the disconnector spring suppossed to be, Big side up or down? Ive seen both and big side up the disconnector will not fit so I currently have it big side down.

                              Comment

                              Working...
                              UA-8071174-1