Kimber rusting issues screwed me...

[fullmd]

was looking at handguns at turners and the employees were telling me that kimber is having quality issues and are rusting while sitting in the store

[bigcory707]

I have one pro carry ii stainless and one custom. Neither have had any issues but as previously stated, I oil and clean it all the time

[MontClaire]

XDS is polymer. No rust and weights less. Kimber is great if it's not rusting. Unfortunately you weren't as fortunate with it. Explore other options. They are a plenty. Glock, HK, Springfield, etc. Even other make 1911 models.

[G-Man WC]

Kimber's metal\rusting has been known issue for awhile.
Flame suit on!
-g

[faris1984]

Flitz polish to take off the rust. Will not harm the finish.
I carried one of these shorties for about 6 years. Good little piece.

This.

[FeuerFrei]

I always wanted to carry 45acp but not thrilled with the weight since all i have are all full size pistol.. Now i look around and found this kimber ultra CDP II that has a 3"barrel and has a considerably tolerable weight maximum i can carry.. I heard about barrel getting rusted here and there but i never really paid attention to it since this is a brand new pistol and assuming all those issues before has been resolved by kimber already. I bought her and few shots down the pipe then back to the box coz i decided to clean her later that week. After 2 weeks i have noticed that bothe sides of the grip safeTy bump has rust on it.. I looked into the barrel and cleaned it, its clear and clean so far. Just the grip safety bump showing a little bit of discoloration and on its side surely rusting.. This part of the gun is not even bare metal, its coated somehow still rusting .. What should i do? Anybody have the same experience?

Flitz polish to take off the rust. Will not harm the finish.
I carried one of these shorties for about 6 years. Good little piece.

[faris1984]

why the hell Sigs or other full metal frames don't have this issue?,Kimber is expensive and they should make it out of a better metal quality.Youtube is full with rusty kimbers.

[faris1984]

I don't like polymer pistols but when I got my CCW I bought one so I don't care about rusting and weight . A smaller full metal frame is no where near polymer.
I'm so happy with it that I decided to get another polymer gun for plinking and training , I don't have to care about scratches or rust and I can put micro red dot on it.Calgunners advised me to get a polymer gun and I didn't regret it.

[JDay]

Kimber is all hype. They're cheap mass produced 1911s. Sig makes a fine 1911 for less.

[glockman19]

I always wanted to carry 45acp but not thrilled with the weight since all i have are all full size pistol.. Now i look around and found this kimber ultra CDP II that has a 3"barrel and has a considerably tolerable weight maximum i can carry.. I heard about barrel getting rusted here and there but i never really paid attention to it since this is a brand new pistol and assuming all those issues before has been resolved by kimber already. I bought her and few shots down the pipe then back to the box coz i decided to clean her later that week. After 2 weeks i have noticed that bothe sides of the grip safeTy bump has rust on it.. I looked into the barrel and cleaned it, its clear and clean so far. Just the grip safety bump showing a little bit of discoloration and on its side surely rusting.. This part of the gun is not even bare metal, its coated somehow still rusting .. What should i do? Anybody have the same experience?

Of my 5 Kimbers, I have not had this problem. Probably because I clean and oil my firearms after every use. I have carried my Pro Carry II for months without any rust.

Clean your gun and oil it and you won't have rust issues.

[repomanNWP]

Stop buying Kimber. Polymer doesn't rust 😀

Sent from my SM-G920T using Tapatalk

[springer19]

I always wanted to carry 45acp but not thrilled with the weight since all i have are all full size pistol.. Now i look around and found this kimber ultra CDP II that has a 3"barrel and has a considerably tolerable weight maximum i can carry.. I heard about barrel getting rusted here and there but i never really paid attention to it since this is a brand new pistol and assuming all those issues before has been resolved by kimber already. I bought her and few shots down the pipe then back to the box coz i decided to clean her later that week. After 2 weeks i have noticed that bothe sides of the grip safeTy bump has rust on it.. I looked into the barrel and cleaned it, its clear and clean so far. Just the grip safety bump showing a little bit of discoloration and on its side surely rusting.. This part of the gun is not even bare metal, its coated somehow still rusting .. What should i do? Anybody have the same experience?