Unconfigured Ad Widget

Collapse

MOSSBERG 930

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • #16
    FeuerFrei
    Calguns Addict
    • Aug 2008
    • 7455

    Originally posted by fell
    Has anyone put the SBE gas piston in their 930? Wondering what your thoughts are on their piston, and how it preforms. The 930 is a nice gun, shoots light loads with no problems.
    If you clean and maintain the gas system properly it just runs and runs. I have a gen 1 spx and it has given me no problems cycling until it gets VERY dirty.

    930's run very well with little lube as long as you put it in the correct locations.

    Comment

    • #17
      pennstater
      Veteran Member
      • Aug 2010
      • 4677

      Originally posted by FeuerFrei
      If you clean and maintain the gas system properly it just runs and runs. I have a gen 1 spx and it has given me no problems cycling until it gets VERY dirty.

      930's run very well with little lube as long as you put it in the correct locations.
      This^^^^^ right here. Simple stuff.

      Comment

      • #18
        lincoln45
        Member
        • Jan 2012
        • 379

        Originally posted by FeuerFrei
        If you clean and maintain the gas system properly it just runs and runs. I have a gen 1 spx and it has given me no problems cycling until it gets VERY dirty.

        930's run very well with little lube as long as you put it in the correct locations.
        and where are those loacations ?

        Comment

        • #19
          FeuerFrei
          Calguns Addict
          • Aug 2008
          • 7455

          Originally posted by lincoln45
          and where are those loacations ?
          The bolt slide inside the receiver grooves and the gas rings. Contact points will show you where to put oil on the slide itself.

          Everything else can be wiped down with an oily rag. Bolt body, gas system pusher assembly and externals. When the gas/mag tube gets too crusty I use a scotch brite pad on it and then hit it with the oily rag.

          A needle oiler is what I use if it needs a touch up before I take it out for a run. Most of the time it doesn't need it. I like that.

          Comment

          • #20
            ysr_racer
            Banned
            • Mar 2006
            • 12014

            What happened to all the good info in this thread?

            Comment

            • #21
              W.R.Buchanan
              Veteran Member
              • Jan 2008
              • 3412

              There is a good article on the 940JM in the current NRA Magazine which I'm sure all of you get, cuz you're all NRA Members Right? If not, Fix that FIRST!!!

              The article talks about all the shortcomings of the 930 all of which revolve around cleaning the gun more often. They claim < every 500 rounds. The JM940 can go 1500 rounds.

              Long and the short of it is you really need to clean your guns more frequently, and the 930 is one you just have to be a little more religious about doing.

              Randy
              Rule #1 Liberals screw up everything they touch.
              Rule #2 Whatever they accuse you of, they are already doing.
              Rule #3 Liberals lie about anything no matter how insignificant.
              Rule #4 If all else fails, they call you a Racist!

              It's not how well you do what you know how to do,,, It is how well you do what you don't know how to do.
              www.buchananprecisionmachine.com

              Comment

              • #22
                ysr_racer
                Banned
                • Mar 2006
                • 12014

                Originally posted by ysr_racer
                What happened to all the good info in this thread?
                See above ^^

                Comment

                • #23
                  Munny$hot
                  Veteran Member
                  • Jul 2011
                  • 3665

                  I have a JM Pro 22" which is also from the 930 family. There are some mods that you want to do before calling it good for a true HD rig.
                  1) Debur and round off the front of the mag tube follower
                  2) Be sure the mag tube/extension has no burs or high spots the follower can hang up on.
                  3) Drill 3/8"-1/2" holes onto the piston transfer tube similar to the OR3GUN or 940 JM Pro transfer tube to prevent cycling issues.
                  4) Never press the bolt release with the bolt forward because it will cause a double feed from the mag tube and lock up your gun bad, but learn how to clear one should it happen, because it will.
                  5) Take apart and clean your piston, piston housing and exterior of your mag tube extremely well after every use.
                  6) Debur the recoil spring ends and reprofile the recoil plunger and debur the inside of the recoil spring tube housing if necessary.

                  These are known problems on the 930 and will appear at the worst times. Sure. you'll get the answer I put 1 million rounds outta mine and never had a singe problem while never cleaning it while all the people that actually use it hard know of the problems all to well. While I do consider my 930 now HD ready it will not replace my M1 Super 90 Inertia drive for my go to. 930 are great for the money and if you keep it clean and do these simple mods it'll serve its porpoise. Some of these mods can be found on OR3GUN YouTube channel.
                  Can DI AR's run dirty?

                  Palmetto State Armory Suppliers revealed

                  "If it ain't stock, it don't belong on your Glock"

                  Comment

                  • #24
                    pennstater
                    Veteran Member
                    • Aug 2010
                    • 4677

                    BoarHunters posts/pics are gone. What happened? He was the one talking about drilling holes in the spacer. Hmm.

                    MLC

                    Comment

                    • #25
                      k1dude
                      I need a LIFE!!
                      • May 2009
                      • 16331

                      I have a friend that had a 930 that he tried to use for 3-gun. It constantly had problems despite keeping it clean and lubed. It couldn't make it through a match without disassembling and cleaning the gas piston. He finally gave up on it after about 3,000 rounds and bought a 930 JM Pro. He basically had the same problems with the JM Pro.

                      He finally threw in the towel on 930's and bought a Beretta 1301 Competition. He's had no problems with it whatsoever.
                      "Show me a young conservative and I'll show you a man without a heart. Show me an old liberal and I'll show you a man without a brain." - Sir Winston Churchill

                      "I would remind you that extremism in the defense of liberty is no vice! And let me remind you also that moderation in the pursuit of justice is no virtue!" - Senator Barry Goldwater

                      Comment

                      • #26
                        FeuerFrei
                        Calguns Addict
                        • Aug 2008
                        • 7455

                        Originally posted by k1dude
                        I have a friend that had a 930 that he tried to use for 3-gun. It constantly had problems despite keeping it clean and lubed. It couldn't make it through a match without disassembling and cleaning the gas piston. He finally gave up on it after about 3,000 rounds and bought a 930 JM Pro. He basically had the same problems with the JM Pro.

                        He finally threw in the towel on 930's and bought a Beretta 1301 Competition. He's had no problems with it whatsoever.
                        Interesting and too bad he hung up on the 930.

                        I'm no expert/competitor, but I managed to sort out the clean/lube ju ju in short order.

                        Gas systems are finicky regardless of manufacturer if it's not maintained properly.

                        My shotgun had initial teething problems that were sorted out by cleaning and proper lubrication. It ain't an easy Rem 1100 O-ring fix.

                        Dirty burning ammo is nobody's friend either. I only use hi base Fed/Rem factory ammo and haven't reloaded anything for years.

                        Comment

                        • #27
                          Don the savage
                          Senior Member
                          • Aug 2010
                          • 2094

                          Originally posted by fell
                          Has anyone put the SBE gas piston in their 930? Wondering what your thoughts are on their piston, and how it preforms. The 930 is a nice gun, shoots light loads with no problems.
                          Originally posted by dilbert40
                          I don't mean to hijack this thread, but I am curious whether anyone replaced the 930 Forearm Retainer (SKU 16772) from the fragile plastic OEM part to
                          OR3GUN part (http://www.or3gun.com/OR3GUN/about_or3gun_retainer.htm) to make 930 work better. My SPX seems to be more reliable but could not really quantify it.
                          Ive replaced both on mine.
                          Stock retainer exploded during a match and i got the new piston after i had an issue when it was damp out.
                          I have had zero problems since i changed them out. I havent shot 3 gun for a while, but if i shoot shotgun i will put at least 250 rounds through it in a session in a combo of cheap bird ( most of the rounds) buck and slugs. I can take pictures if you want.
                          I support peace through superior firepower.
                          "Para ser libre, un hombre debe tener tres cosas, la tierra, una educacion y un fusil. Siempre un fusil ! (To be free, a man must have three things; land, an education and a rifle. Always a rifle)" -Emiliano Zapata.

                          Originally posted by rsrocket1
                          Of course they are in free territory where they can pick up ammunition at the local 5 and dime without going through a criminal background check. All we get is legalized pot.

                          Comment

                          • #28
                            Boarhuntor
                            Banned
                            • Feb 2019
                            • 760

                            ^^^^ JFYI it is not Цалифорниа, it is Калифорния.

                            Comment

                            • #29
                              Featureless
                              CGN/CGSSA Contributor
                              CGN Contributor
                              • Mar 2018
                              • 2267

                              Originally posted by keith1911
                              I've got a 930 JM Pro and have never had any reliability issues with any type of ammo.
                              How many rounds? What is your maintenance schedule/procedure?
                              California Native
                              Lifelong Gun Owner
                              NRA Member
                              CRPA Member

                              ....."He has erected a multitude of New Offices, and sent hither swarms of Officers to harrass our people, and eat out their substance."

                              Declaration of Independence, 1776

                              Comment

                              Working...
                              UA-8071174-1