Unconfigured Ad Widget

Collapse

Ruger Mark III Ftf Issues HELP

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • nor_cal_ryan
    Member
    • Jun 2010
    • 379

    Ruger Mark III Ftf Issues HELP

    Hello fellow cal gunners. I was hoping some of you could help diagnose an issue with my Ruger Mark IIII. I bought the pistol new, and have run about 500 rounds through it and it has always had failure to fire issues regardless of which ammo I use. I have tried federal bulk pack, Winchester white box, cci mini mags, etc. all with the same result. Now a little about my gun to give you some background. Upon purchase I had installed the volquartsen mark 2 trigger kit, and speed bolt kit. I religiously clean my gun after every range visit. I am completely stumped. At first I thought that the gun was breaking itself in, but after 500 rounds I would have figured all the hiccups would have worked themselves out. Do you guys have any suggestions? I am at the point where I a, going to switch the stock internals back, but would really hate to loose the awesome trigger in the upgraded kit.
    Thanks for the help, Ryan
  • #2
    AK4me
    Senior Member
    • Mar 2008
    • 1282

    Have you shot it at all with the stock internals. I have one thatis completely stock and it rarely has any problems, I use CCI minimags, and federal or winchester bulk, and I almost never clean it.
    sigpic

    Comment

    • #3
      nor_cal_ryan
      Member
      • Jun 2010
      • 379

      I shot maybe 5 mags through the gun before I switch out the internals. It had a few failure to fires with the stock internals. Currently with the volquartsen internals I would say on average I have 2-3 Ftf per mag regardless of the ammo.

      Comment

      • #4
        checkenbach
        Senior Member
        • Nov 2008
        • 1469

        You need to adjust you trigger with the Allen wrench that came in the kit.
        That's what the hole in the trigger is for.

        Comment

        • #5
          nor_cal_ryan
          Member
          • Jun 2010
          • 379

          I thought that might be the issue, I have taken the Allen screw completely out, and still have the ftf issue

          Comment

          • #6
            rogervzv
            Senior Member
            • Feb 2011
            • 2087

            I have 4 stock Mark pistols and they NEVER have FTF issues. Something is seriously not right here. I agree with the other poster in this thread; restore your pistol to complete stock and start over.

            One thing: make sure your magazines are fully seated. Good luck.
            Come and Take It!
            I'm the only hell my momma ever raised ...

            Comment

            • #7
              INFAMOUS762X39
              Senior Member
              • Jan 2012
              • 1458

              To me, it sounds like:
              -Magazine Issue. Bad Follower or spring?
              -Extractor or Extractor Spring may be to tight. Too tight of an extractor=FTF, loose extractor=FTE etc.
              -or Your chamber/breech may be out of spec, contact Ruger.

              Like the guys said, go back to stock and go from there.

              I love my Ruger MKIII 22/45, only VQ part I run is a Exact Edge Extractor and Mag Bushing. She Feeds and Ejects great. I gave mine a trigger polish job. Dropped 2lbs, breaks at 3.5lbs..perfect!

              Comment

              • #8
                TKM
                Onward through the fog!
                CGN Contributor
                • Jul 2002
                • 10657

                You "improved" it too much.

                Go back to stock and change parts one at a time as you see fit. When it stops running properly go back one step and try a different approach.
                It's not PTSD, it's nostalgia.

                Comment

                • #9
                  davidb
                  Senior Member
                  • Sep 2010
                  • 1769

                  what do the firing pin marks look like when the ftf's happen? when cleaning do you get around the firing pin good?

                  im thinking if you keep it clean and its not the ammo, it may be all the upgrades...mine has been flawless for 1000's of rounds pretty much stock ( only upgrade is a mk ii hammer bushing )

                  Comment

                  • #10
                    Chaos47
                    Calguns Addict
                    • Apr 2010
                    • 6615

                    Did you do the Volquartsen Hammer too?
                    Most say avoid it, its too light and causes light strikes...

                    Comment

                    • #11
                      problemchild
                      Banned
                      • Oct 2005
                      • 6959

                      Same gun- Same issue- SOLVED!


                      Go to RFC and buy the loaded chamber indicator blockoff, remove your lci. Also buy the magazine disconnect bushing from VQ or the BAM bushing at rfc, remove your magazine disconnect. The gun WILL NOT FUNCTION correctly with those two items in the gun NO MATTER what others say. In my case the magazine disconnect was rubbing on the hammer keeping it from striking hard enough and the LCI was keeping the gun from feeding and ejecting.

                      My gun now runs 100% ALL THE TIME!

                      IM NOT responsible for you having any accidents after doing so or ruining your gun. DONT take my advice if you cant live with the results.
                      Last edited by problemchild; 06-29-2013, 7:42 AM.

                      Comment

                      • #12
                        nor_cal_ryan
                        Member
                        • Jun 2010
                        • 379

                        Rfc?

                        Comment

                        • #13
                          sofbak
                          Veteran Member
                          • Aug 2010
                          • 2628

                          Originally posted by nor_cal_ryan
                          Rfc?
                          Rimfirecentral.com
                          Tire kickers gonna kick,
                          Nose pickers gonna pick
                          I and others know the real

                          Comment

                          • #14
                            rogervzv
                            Senior Member
                            • Feb 2011
                            • 2087

                            Originally posted by problemchild
                            Same gun- Same issue- SOLVED!

                            Go to RFC and buy the loaded chamber indicator blockoff, remove your lci. Also buy the magazine disconnect bushing from VQ or the BAM bushing at rfc, remove your magazine disconnect. The gun WILL NOT FUNCTION correctly with those two items in the gun NO MATTER what others say.
                            Well, I own three Mark IIIs that are stock, and all three of them run beautifully with the LCIs, which I consider to be a "feature not a bug." I like the LCI. I frankly doubt than the LCI has any effect one way or the other on the way the gun functions so long as you take 30 seconds to clean it after each range outing.
                            Come and Take It!
                            I'm the only hell my momma ever raised ...

                            Comment

                            • #15
                              problemchild
                              Banned
                              • Oct 2005
                              • 6959

                              Originally posted by rogervzv
                              Well, I own three Mark IIIs that are stock, and all three of them run beautifully with the LCIs, which I consider to be a "feature not a bug." I like the LCI. I frankly doubt than the LCI has any effect one way or the other on the way the gun functions so long as you take 30 seconds to clean it after each range outing.
                              And I can show you 100 posts at rfc that says it DOES get in the way.

                              Someone always has to say MINE WORKS RIGHT with the crappy parts.
                              Mine didnt and neither do another 100,000 of them. Whats your point?

                              And I will BET YOU that when the OP FIXES his gun with the parts that his will work correctly too.

                              Wanna take that bet? How about pinks on your 3 "working" guns?

                              Why does a person need a LCI if they handle the gun correctly? There hasnt been LCI's on guns for over 100 years and there was NO ISSUE! The LIBTARDZ come along and want LCI, Laser fingerprinting, copper bullets, no copper bullets, magazine disconnects etc. All of them create more problems then they solve. How bout we BAN democrats instead of lead bullets?
                              Last edited by problemchild; 06-29-2013, 2:57 PM.

                              Comment

                              Working...
                              UA-8071174-1