Removeable fin grip?

[dirtystranger]

Does anyone know if there is fin grip or reasonable facsimile made that will slip over the pistol grip on an AR and quickly remove? I figure it'll be easier to deal with than these stupid mag lock devices.
Any direction on this subject is greatly appreciated.

Thanks

[Lucky Scott]

I get all of mine from this guy on this forum......
munkeeboi

I think all of the fins are removable.

[dirtystranger]

Thanks

[morrcarr67]

Does anyone know if there is fin grip or reasonable facsimile made that will slip over the pistol grip on an AR and quickly remove? I figure it'll be easier to deal with than these stupid mag lock devices.
Any direction on this subject is greatly appreciated.

Thanks

You do have to take the grip off the rifle to change the back straps, but it's still a pretty quick swap.

https://www.aimsportsinc.com/california-featureless-ar-grip/

They also have stock locks and muzzle brakes.

Sent from my P00C using Tapatalk

[afteractionreport]

Exile machine backfin with magpul miad grip...

[????? ????]

Exile Machine out of business so the backfins aren’t so easy to get.

[kcheung2]

Just click BUY NOW

http://www.amazon.com/Machine-Backfin-Backstrap-Mission-Adaptable/dp/B07145KZQ1/ref=cm_wl_huc_item

[hellayella]

https://www.fingrips.com

[deckhandmike]

I’d get a 10$ strike industries fin grip. It’s a built in piece but for 10$ it’s solid. If you want to switch it out it’s one bolt to change to a standard grip. You could probably switch grips quicker than removing a three bolt slide on fin grip that cost 30$.

[Sparrow Dynamics]

I think what you are looking for is a Kydex grip wrap. Check out munkeeboi in this forum for that. Swapping out a grip on a AR is fairly quick though, and our grip still allows you to wrap your thumb around. It is worth a look. Either option is good in that you wouldn’t be sending dollars overseas.

[ar15barrels]

Does anyone know if there is fin grip or reasonable facsimile made that will slip over the pistol grip on an AR and quickly remove?

An AR pistol grip is held on by ONE screw.
The grip wrap is held on by 3 screws.
It's probably faster to just swap pistol grips than to remove and then re-install 3 screws if you use an allen-head screw to hold the pistol grip.
An allen wrench is easier to manipulate than the slot screws used to hold on a grip wrap because the allen wrench stays in the socket head so much easier than a slot screwdriver stays in a slot head.

Keep one grip with a fin and another without.

[stix213]

An AR pistol grip is held on by ONE screw.
The grip wrap is held on by 3 screws.
It's probably faster to just swap pistol grips than to remove and then re-install 3 screws if you use an allen-head screw to hold the pistol grip.
An allen wrench is easier to manipulate than the slot screws used to hold on a grip wrap because the allen wrench stays in the socket head so much easier than a slot screwdriver stays in a slot head.

Keep one grip with a fin and another without.

But you remove the grip and forget about the spring, and then you spend an hour on the floor trying to find it!

[ar15barrels]

But you remove the grip and forget about the spring, and then you spend an hour on the floor trying to find it!

Speak for yourself.

[Syntax Error]

Kydex overwrap grip fins should all be removeable, unless you're a dumb-dumb and use rivets instead of screws to secure the two sides together.

[Donk310]

But you remove the grip and forget about the spring, and then you spend an hour on the floor trying to find it!

HAHA! Right! Plus that ONE screw is a pain in the ***.