KRG Bravo Chassis

[5.56Geo]

I like my KRG Bravo chassis! I drank the entire KRG Kool-Aid jug! I also bought KRG magazines, small bolt lift, extended mag release and stock hook plate.

Here is a picture of mine.

[boyguan]

I like my KRG Bravo chassis! I drank the entire KRG Kool-Aid jug! I also bought KRG magazines, small bolt lift, extended mag release and stock hook plate.

Here is a picture of mine.

Black?

[michaelthepsycho]

Can the cheek piece be moved fore and aft? I run a long LOP, and like the cheek piece to move along with it. Too many stocks on the market don't allow for that, but I remember the Whiskey-3 can do it (a little bit).

[5.56Geo]

Black?

Yes mine is black. They are offered in Sako Green, FDE and Black. The black being priced at $349. The other two colors are a few dollars more.

Can the cheek piece be moved fore and aft? I run a long LOP, and like the cheek piece to move along with it. Too many stocks on the market don't allow for that, but I remember the Whiskey-3 can do it (a little bit).

The check raiser can only be adjusted up and down.

[NorCalFocus]

Finally a pic of the sako green chassis. I was debating whether to get this color or black because I wasn't sure about the shade of green it was. Looks beautiful in this color and I think I'll order one....as soon as they are back in stock for the Tikka.

Just be sure to order all the little add on parts at the same time. They don't charge extra shipping for all those when you order a stock. I strongly suggest getting the extended driver, the butt hook cover, and extended mag release. I also thought about getting the spigot plug and I may go back and get the Harris bi-pod fixed mount.

[jimmykan]

The extended driver is a must if you use a torque-limiting driver tool like the Wheeler FAT Wrench to tighten your action screws.

Otherwise, you'll have to take off the plastic forend, tighten the action screws using the FAT Wrench, then replace the forend.

[NorCalFocus]

I kinda hate that they nickel and dime you on these little small parts...like the hook plate and mag release. Good call on the extended driver also. I thought it came with some kind of stud to fit a harris bipod?

[Fergi_B_Good]

That chassis/stock looks nice! I have a X-ray that is quite comfortable...except I can never find a comfortable place to put my thumb...The Bravo looks like it's the solution. Thanks OP for the pictures!

[boyguan]

This thing looks so sweet. I don’t like to copy it but I think you helped make up my mind. Sako green

[JTROKS]

Nice looking stock and price competitively.

No bedding. It's a drop in design. I torqued it down to 65in pounds per the instructions.

Well, almost...

[NorCalFocus]

Randall's comment to me was based on a convo I had with him on this. I had him install a tapered lug when he did my barrel back in June. The Bravo will not fit a tapered lug, you have to have a straight profile lug. So I had some help from a buddy and we re-shapped my lug to fit.

So as long s you have the right shaped lug, its a drop in fit.

[ar15barrels]

Unlike HS and B&C, most chassis systems use a V block system to set the round receiver into.
The V block design depends on the receiver actually being straight/round, which is often not the case.
The next problem with V blocks is that they do not properly support the tang of the receiver.
Due to the V arrangement and the long skinny tang, the tang is always being bent down as the rear screw is torqued.

I have yet to see a V block chassis holds a 700 receiver stress free.
Most chassis systems will benefit from a proper bedding job so that the receiver is held stress free.

[boyguan]

Unlike HS and B&C, most chassis systems use a V block system to set the round receiver into.
The V block design depends on the receiver actually being straight/round, which is often not the case.
The next problem with V blocks is that they do not properly support the tang of the receiver.
Due to the V arrangement and the long skinny tang, the tang is always being bent down as the rear screw is torqued.

I have yet to see a V block chassis holds a 700 receiver stress free.
Most chassis systems will benefit from a proper bedding job so that the receiver is held stress free.

If you bed a chassis for a particular action can it later be changed and Renee for another action?

[sigstroker]

Unlike HS and B&C, most chassis systems use a V block system to set the round receiver into.
The V block design depends on the receiver actually being straight/round, which is often not the case.
The next problem with V blocks is that they do not properly support the tang of the receiver.
Due to the V arrangement and the long skinny tang, the tang is always being bent down as the rear screw is torqued.

I have yet to see a V block chassis holds a 700 receiver stress free.
Most chassis systems will benefit from a proper bedding job so that the receiver is held stress free.

What about Savages? Oh wait, you don't work on Savages.

[longrange1]

What about Savages? Oh wait, you don't work on Savages.