Unconfigured Ad Widget

Collapse

DELETE

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • #16
    TheOriginal
    Member
    • Oct 2014
    • 228

    Originally posted by 3006Garand
    Wilson Combat. I bought a few parts for my Springfield 1911, and about to order more.
    what did you order? can you tell me the specific parts? thanks!

    Comment

    • #17
      himurax13
      Veteran Member
      • Aug 2009
      • 3895

      Originally posted by Mossy Man
      it doesn't HAVE to be, especially if you use the WC drop in one.

      Sure the finishes may not match, but since you didn't have to shave the frame to round it off properly ( [emoji14] ) you don't have to worry about bare metals.

      I didn't care as much about looks as I did not getting a bloody hand web every time I shot the gun (i tend to hold high since I mainly shoot glocks)

      WC Drop in hammer, sear, beavertail saftey. The safety took fitting, but the hammer and sear basically dropped in. It's not a target trigger/sear setup, but it's still good and slightly better than factory. Passed all the safety tests as found all over the internets.

      Sure, go ghetto why don't we.

      Selecting the appropriate beavertail is important. I believe there is a specific one for the Springfield milspec frame.

      You will also have to replace the hammer.
      Last edited by himurax13; 01-22-2015, 8:26 PM.
      Originally posted by Bumslie
      HK - the best 600 dollar gun, 900 dollars can buy.
      Originally posted by Sleighter
      Getting legal advice from a gun salesman, is like getting medical advice from a janitor at a hospital. Both make about the same per hour and both prove that being around something all day doesn't make you an expert.

      Lifetime NRA member.

      Comment

      • #18
        Mossy Man
        Calguns Addict
        • Jun 2011
        • 7641

        Originally posted by himurax13
        Sure, go ghetto why don't we.

        Selecting the appropriate beavertail is important. I believe there is a specific one for the Springfield milspec frame.
        we beavertail now

        Comment

        • #19
          heidad01
          Veteran Member
          • Feb 2012
          • 4902

          If you change the grip safety to a beavertail, you also have to change the hammer or cut/bob your spur hammer. A standard spur hammer will not work with a beavertail.
          Ambi is no problem, take out the old one and put the new one in. May need minor fitting which is no big deal.

          Comment

          • #20
            ruchik
            Senior Member
            • Apr 2010
            • 1189

            Originally posted by TheOriginal
            what did you order? can you tell me the specific parts? thanks!
            Just so you are aware, the vast majority of 1911 parts will need fitting to your specific gun. That's just how it is, due to manufacturing differences between all the 1911 makers.

            Comment

            • #21
              3006Garand
              Senior Member
              • Jan 2013
              • 927

              Originally posted by TheOriginal
              what did you order? can you tell me the specific parts? thanks!
              I have a 1911 Springfield Loaded with the Parkerized finish, and tritium night sights. You need an Allen Wrench to take it down. I bought the Wilson Combat parts so I don't need any tools to take it down. And also, LOL, I'm buying parts to make it a little bit more like yours. I bought a single sided safety. I don't think I want a magwell. But, I think I might send it to the Gunsmith for 25 L.P.I front strap checkering, and to cut the muzzle flush with a bevel, and a nice black/blue finish.
              I'm going to shoot this gun, and wear it in, scratch, blemish, for a while before I get that work done at the gunsmith.
              I also bought some nice Wilson Combat mags. The more the better.
              Also, I got some VZ G10 grips.
              Have fun with you new pistol. There's a lot you can do with it.
              Last edited by 3006Garand; 01-23-2015, 3:17 AM.
              100% deplorable

              Comment

              • #22
                TheOriginal
                Member
                • Oct 2014
                • 228

                Originally posted by heidad01
                If you change the grip safety to a beavertail, you also have to change the hammer or cut/bob your spur hammer. A standard spur hammer will not work with a beavertail.
                Ambi is no problem, take out the old one and put the new one in. May need minor fitting which is no big deal.

                oo thats too much then, maybe down the road. I guess all stick to the ambi safety for now since thats the most important for me.


                Originally posted by ruchik
                Just so you are aware, the vast majority of 1911 parts will need fitting to your specific gun. That's just how it is, due to manufacturing differences between all the 1911 makers.
                Gotcha, Hopefully I can find parts close enough without doing too much.

                Originally posted by 3006Garand
                I have a 1911 Springfield Loaded with the Parkerized finish, and tritium night sights. You need an Allen Wrench to take it down. I bought the Wilson Combat parts so I don't need any tools to take it down. And also, LOL, I'm buying parts to make it a little bit more like yours. I bought a single sided safety. I don't think I want a magwell. But, I think I might send it to the Gunsmith for 25 L.P.I front strap checkering, and to cut the muzzle flush with a bevel, and a nice black/blue finish.
                I'm going to shoot this gun, and wear it in, scratch, blemish, for a while before I get that work done at the gunsmith.
                I also bought some nice Wilson Combat mags. The more the better.
                Also, I got some VZ G10 grips.
                Have fun with you new pistol. There's a lot you can do with it.
                Yeah. no magwell for me!, Is it difficult to gunsmith yourself? Compare it to building an AR-15? I guess ill just stick to ambi safety for now.



                and does anyone know if laser engraving the slide is very expensive?

                Comment

                • #23
                  Pupulepeter
                  Senior Member
                  • May 2012
                  • 783

                  Originally posted by TheOriginal
                  honestly all I want is the ambi safety, and beaver tail. nothing more nothing less. Im not looking to make it look like optimus prime, I just want to add safety. Ive shot the gun before, and never had any problems. Totally loved it, but I definitely want the ambi safety.



                  If I want to do cosmetics maybe laser engravings, and pearl grips
                  The point is that it doesn't work that way. The safety needs to be hand fitted to the sear and frame, which will require file work and possibly refinishing. The hammer needs to be bobbed or replaced if you want a beavertail grip safety. Of course, that means you probably need to replace the sear since it needs to be mated to the hammer.

                  The beavertail needs to be fitted to the frame, which means the rear tangs must be filed down to match the radius on the safety. After which everything will need to be blended with a dremel, files and paper. The safety will also need to be fitted to the trigger bar.

                  Or you could buy the drop in stuff, have a crappy and possibly unsafe trigger pull, a grip safety that may or may not work correctly and features a huge gap behind the tangs that doesn't match the radius of the grip.

                  1911s are not Glocks, AR style rifles or even SIGs for that matter. You can't drop in parts. Even the ones that say they drop in usually require fitting to be safe. Everyone you quoted was giving you exactly what you were looking for, nothing more, nothing less. The point was to illustrate that there was more to it than you think.

                  Sounds like you are better off selling it and buying a Loaded. Better yet, keep it and buy a Loaded!

                  Comment

                  • #24
                    Pupulepeter
                    Senior Member
                    • May 2012
                    • 783

                    Have a smith fit your safety. You'll notice it is one of the more expensive items on their price list... there is a good reason why.

                    Comment

                    • #25
                      Dinosaur Jr
                      Senior Member
                      • May 2012
                      • 1707

                      Wilson Combat...done.
                      Laws against murder and attempted murder should have been the only gun control laws ever needed in America...

                      Comment

                      • #26
                        Mossy Man
                        Calguns Addict
                        • Jun 2011
                        • 7641

                        For the price diff. Between modding the gun yourself, you are better off selling it and buying a loaded. Can probably sell the milspec for 600, then put $300ish toward the loaded which is around $950.

                        Reminds me of all those guys in the 90s who wanted to swap their automatics for manuals.....cheaper/easier/softer to sell and buy.

                        I did what I did because the gun was a gift from dad and I will never sell it, and none if the intended arts are permanent mods. Still have my old parts if I want to take it back to OEM.
                        Last edited by Mossy Man; 01-23-2015, 3:57 PM.

                        Comment

                        Working...
                        UA-8071174-1