Unconfigured Ad Widget
Collapse
|
|
|
|
|
|
|
|
My Python project - returning her to glory
Collapse
X
-
I found both on the Colt Forum. The barrel was reasonability priced cause it did not have the Colt roll marks. If it did, it'd be worth big $$$$ as some unscrupulous sellers could change the barrel on a 6 inch and resell it as a "Original 3 inch" Python ($2K vs $5K)
The guy selling the barrel just asked in passing if I would be interested in a unfluted cylinder. AH YEAH!!! In fact he had two and I bought them both (only had one 3" barrel though).Last edited by Aircraftman; 06-05-2014, 8:19 PM.Comment
-
-
What a journey!! I can't wait for the destination!My Marketplace Feedback: https://www.calguns.net/forum/market...k#post54003245Comment
-
No, just for the application of the charcoal bone witches brew bluing. It's only a couple hundred bucks. If you let Ford or Coogan or even Colt take it to the buffer they will ruin it. That gun needs fine grit sandpaper attached to a flat block with double sided tape. That's how you polish metal the old pre-war way. You have done 90% of the work. You can finish it.
All these finishers use buffers and they polish the side plate off the gun. Do the sharp edges are rounded off and the gun looks like crap.
Another good one is Hamilton Bowen. They can do it the old way as well.Comment
-
This is probably the coolest thread on the entire internet!"Bye Felicia!" - Said by me, as I looked at Kalfornia in my rearview for the last time, 9/22/17.
NRA member
My experience is from the '80's and '90's, when mullets ruled the world!
If azzholes could fly, this place would be an airport!
I support gun control.....if there's a gun around, I want to be in control of it!
You go ahead and give peace a chance. I'll cover you if it doesn't work out!Comment
-
I like it!!!! Plus once I get the engraving quote I will probably go this direction anyway...Comment
-
Very interesting. I might reach out to you on PM for a little more info on this concept. This gun is already in Alabama and moving forward. But I have another candidate for this procedure. Thanks for the idea!!No, just for the application of the charcoal bone witches brew bluing. It's only a couple hundred bucks. If you let Ford or Coogan or even Colt take it to the buffer they will ruin it. That gun needs fine grit sandpaper attached to a flat block with double sided tape. That's how you polish metal the old pre-war way. You have done 90% of the work. You can finish it.
All these finishers use buffers and they polish the side plate off the gun. Do the sharp edges are rounded off and the gun looks like crap.
Another good one is Hamilton Bowen. They can do it the old way as well.Comment
-
-
Thank you for just coming out and saying who did what and how much it costs. Its annoying seeing awesome threads like this but then the OP wont say how much was spent or where it was done. Awesome thread... Thanks!Comment
-
I look forward to the outcome. If it were me, I would leave the barrel 'sterile'. Maybe the frame too- it would look awesome with the unfluted cylinder.
And go for a brushed look on the finish- brushed hard chrome? I think it would look like a million bucks.
A fancy set of dark wood grips for the finish (I suggest KN Nill Griffe if they make something for the Python).
-DaveComment
-
Thanks for the update, OP. It already looks great!You will never, in your life, have a chance like this again.
If I were you, I would not pass this up. I would not let this go by...this is rare.
Come on...what harm??
joefrank64k 251/251 100% iTrader?Comment
-
Just as a side note:
You should rename the thread. You are not actually returning the gun to it's glory. You have changed the cylinder and the barrel. That's not returning. What you are doing is rescuing. You are saving a very valued firearm from an untimely demise. It took a few replacement parts to do it, but ultimately you will have saved it from the fire. It's really just a matter of semantics.
My vote would be to go with leaving everything sanitary, no engraving, and with a brushed hard chrome, or NP-3 finish. Why? Because it will be unique. The mods done have all ready made it unique, so why not continue that theme? What pops into your head when you hear the words, "Colt Python?"
I usually think of a 4" - 6" vent-rib barrel and the engraved, "PYTHON" on a blue gun. Yours won't do that. But yours will be the one talked about. You have a visual history of the gun, so any nay-sayers saying it's not a true Python can pound sand.
And you can name it, "Monty."
Good job and am also waiting it's finished status.
RyanThe following statement is true.
The preceding statement was false.Comment
-
OP needs to make a decision on the finish. The finish will require all the surface pits (corrosion) to be blended with the surrounding metal before any Chroming or Bluing process. How much grinding, draw-filing, grit blasting or glass beading can the base metal endure before changing the shape and contour for the Colt? I think bluing would be out of the question because any pits left behind would become distinctly obvious. It might be able to get hard chromed if pre-coatings of acid copper and bright nickel could fill the pits. OP needs to consult with a process metallurgist. OP may have no choice but to succumb to body filler and paint. Follow your heart OP, you obviously have love for this Colt.
Comment
Calguns.net Statistics
Collapse
Topics: 1,870,703
Posts: 25,175,079
Members: 358,862
Active Members: 5,389
Welcome to our newest member, 1776 Arms.
What's Going On
Collapse
There are currently 19640 users online. 158 members and 19482 guests.
Most users ever online was 239,041 at 11:39 PM on 02-14-2026.


Comment