Try Centerfiresystems.com they sell some Uzi parts.
Unconfigured Ad Widget
Collapse
|
|
|
|
|
|
|
|
Problem with Uzi
Collapse
X
-
Call Vector Arms and see if they will put it together for you in working order!! UZI's are not like AR's where you can mix and match without problems.Comment
-
I am posting two pics. I have adjusted the brightness and contrast so that you can see the parts.Post a good photo of your fcg installed in your grip frame. Remove the grip frame from the receiver and take it from the top down.
You should be able to push the sear down and have it hook in place for the photo. It's normal for the sear to pop up like that when the lower is not attached to the receiver.
Take care,
DaveOriginally posted by Alan GuraThe Second Amendment now applies to state and local governments. Our lawsuit is a reminder to state and local bureaucrats that we have a Bill of Rights in this country, not a Bill of NeedssigpicOriginally posted by hoffmang12050[CCW] licenses will be shall issue soon.
-GeneComment
-
Thanks for the photos. You're missing a part. There is a small wedge shaped piece of metal that goes on the sear pin and sits between the sear spring. I can try to get a better description for you this evening.
Take care,
DaveComment
-
I think you are talking about the disconnector stop, shown here, http://files.uzitalk.com/reference/p...emblelower.htm
But I've been told that it is an optional item. That it isn't required for semi-auto operation, and that it worked fine without it, but was added later.Jack
Do you want an AOW or C&R SBS/SBR in CA?
No posts of mine are to be construed as legal advice, which can only be given by a lawyer.Comment
-
That's it. Disconnector stop. Pretty sure you need it, it's been on the various semi auto lowers I've seen.I think you are talking about the disconnector stop, shown here, http://files.uzitalk.com/reference/p...emblelower.htm
But I've been told that it is an optional item. That it isn't required for semi-auto operation, and that it worked fine without it, but was added later.
Take care,
DaveComment
-
If you can, please post this in the gunsmithing section. We have talked a little bit about the UZI.Life is like having a map with precise directions and exact stops, you find out that your directions and stops change as you progress further down your original map.Comment
-
do you have the disconnector in your lower receiver? looks bare between the spring coils of you sear to me/
It's optional on a working gun. It helps keep you from over tightening the fit between the reciver and lower when putting tgether a new weapon/I think you are talking about the disconnector stop, shown here, http://files.uzitalk.com/reference/p...emblelower.htm
But I've been told that it is an optional item. That it isn't required for semi-auto operation, and that it worked fine without it, but was added later.Attached FilesLast edited by pTa; 01-13-2011, 11:02 PM.sigpicComment
-
Tighten the gap between your pistol grip and receiver. You can test this by holding the lower to the receiver with more pressure. Really lean on it.
(are you maglocking or finning the pistol grip?)Last edited by tonelar; 01-14-2011, 12:02 AM.sigpicComment
-
.............the UZI 9mm, phased plasma rifle in the 40 watt range. Just what you see buddy.Comment
Calguns.net Statistics
Collapse
Topics: 1,870,992
Posts: 25,178,282
Members: 358,862
Active Members: 5,382
Welcome to our newest member, 1776 Arms.
What's Going On
Collapse
There are currently 31031 users online. 114 members and 30917 guests.
Most users ever online was 239,041 at 11:39 PM on 02-14-2026.

Comment